V70 - Misfire :: 1998 GLT - Sporadically Runs Rough / Power Loss
Aug 4, 2013
THE FREQUENCY: This is a condition that has become progressively worse over the last six months. Initially it occurred once a week and now it is happening almost every day, lasts longer and is more acute.
THE SYMPTOMS: Initially and randomly, while driving at any speed, the car would begin to hesitate as if it might stall but did not- The hesitation was much like a shudder or power loss. At this time the check engine light would blink and stay on for a couple of days. This whole event would last less than a minute and the car would return to normal until the next one.
Now, six months later, it is occurring almost every day. At startup, at low speeds, at stop lights.... A LOT!
WHAT HAS BEEN DONE SO FAR: After frequent and unsuccessful visits to the Volvo Dealer all the plugs, the wires, the cap, and the rotor have been replaced with no luck.
The dealer says the code indicates a misfire on the #3 cylinder.
View 3 Replies
Advertisement
Ok I've been plagued with this very random misfire/power loss/hesitation problem going on a couple of months. You could drive the truck anywhere from 50-300 miles without having an encounter of this problem. It seems to do it now mostly on contiguous long trips over like 30 miles. It one time threw up a P1131 code which quickly went away on it's own. This is a list of stuff that has been recently changed: plugs, wires, coil packs, air filter, pcv valve, fuel injectors, tps, idle air valve, MAF cleaned, fuel filter, and egr valve.
I sprayed with brake cleaner for vacuum leaks around the intake tonight after driving a continuous 50 mile round trip it messed a few times on the way back. When I sprayed the EGR valve mounting area it idled rough when it was hit with brake clean and idled up. So there's a leak there. Or is it stuck? It will be driving normal and usually when you come to a stop the engine will start missing really bad and then when you take off there's no power at all. You keep your foot on the gas and eventually it will feel like all the power is just turned on.
If it does it while you're driving highway speeds it will feel like you've lost a cylinder but it's not as dramatic as when you come to a stop and it starts missing. I can't be 100% but I don't think the EGR wasn't leaking before I replaced it and it was still doing the same thing. I'm wondering why the Check Engine Light won't pick up an obvious misfire when you can you actually feel it. And why if it was the vacuum leak would it only start doing it after many miles of driving?
View 11 Replies
Replaced the spark plugs and wires a couple months ago. Started skipping yesterday throwing the #4 misfire code so I replaced the coil pack, reset the check engine light but it's since came back on and has a rough idle and loss of power. By the way, it's a 97 F150 4.6L 4x4 with 200,000 miles.
View 4 Replies
What would cause my truck to have a long turnover start, a really rough idle, and a loss of power after idling at a stop light for about a minute?
This problem gets worse as the truck warms up. It feels as if I'm not getting power from all 6 cylinders but this goes away after about 20 feet of acceleration. The truck has never not started. It just has to turn over for about 5 to 10 seconds before it fires up. I changed the spark plugs and wires thinking it was that and then i tried the fuel filter and it wasn't that either.
View 8 Replies
I have a 2005 Hyundai Sonata 4cyl. and have a misfire problem with the 1st cylinder. I've had it pressure checked and there isn't a problem with the cylinder, such as a ring or warping problem. I've replaced the wires, both boots, both ignition coils and the plugs twice. I was told I need to replace the ignition coil again but I wonder if there is something that is making the coil go bad. I've also replace the throttle position sensor and both O2 sensors. I had the front catalytic converter replaced because it was bogging down and very slow. It still runs rough and the check engine light is on. I was told also that I need to replace the engine speed sensor. I bought the car in Oct. of 2004 and only has 68000 miles on it.
View 2 Replies
My pops has a 86 ranger with a 2.9. And what its been doing is, it will start up just fine then u give it a minute and itll start to run very rough like a bad miss fire, then if he revs it up for a bit. It will clear out and then run just fine until he starts it up again and it seems to do it more the colder it gets and it smells very rich. Iv checked the injectors and there fine, what other things could it be ? O2 sensors oorrr
View 5 Replies
I have a 2003 Chevy Malibu, V6, 3.1, auto, 140k miles. Car started out with code 0420 with no noticeable symptoms, but then added code 0303 (miss fire cyl #3) with loud knock (mostly after warmup) and loss of power under load. Now internal loss of coolant (no puddles or external drips). Changed plugs and wires - no change - all plugs looked good with no sign of contamination. Questions - if this is a valve/piston/lifter problem (which would explain the knock, miss-fire and loss of power), why would I get the loss in coolant? If the loss of coolant is fouling plug #3 (which would explain the coolant loss, miss fire and loss of power), could that give me the loud knocking? I don't see how a valve/piston/lifter issue would cause a leak in coolant but I also don't see how a coolant leak into cyl #3 would give me such a loud knock. Do I have two different problems? If it is a leak into cyl #3, is there any way to tell if it is the intake manifold gasket (which leaked before and was replaced five-six years ago and which I could do again if I had to) or a blown head gasket (which I don't think I could fix or afford to get fixed)? Engine will occasionally get hot (but not overheat).
View 7 Replies
I have a 99 F150 Lariat 4x4 with a 5.4, 150,000 mile on it. About 2 weeks ago I blew spark plug out on #2, and a friend who said he has heli-coiled a bunch of these tried to do mine and ruined the head. Anyway, I called a local engine shop and got another PI head, only I used my cam in it. Torqued it as per the book, etc... Mind you that the engine ran perfect before all this.
Got it back together with all new plugs, new exhaust manifold, and 2 new COP's. When I start it-it runs rough for about a min, then straightens back out to run perfect again, and after a few seconds you can hear a solenoid click, then it goes back to missing again. This goes on and on... I went through all the vacuum lines and checked them, checked the egr valve, put on a new IAC, new PVC, cleaned the MAF, and checked everything else with a DVM.
I took it out and drove it.... Runs good for a minute, then it goes back to missing, then back to smooth again. This just keeps going on and on. I noticed when I hear that click, it sounds like a mad rush of air being sucked in, but I cannot locate it. I ordered a new set of COP's to try next. I can understand if it just plain missed all the time, but this it intermittent. Also, the only code I can get is a too lean on bank 1, so I replaced the 90's and the pvc valve. Now no codes but still in and out of missing. It ran perfect before the new head.
View 3 Replies
I'm having a weird issue with my 1998 Ford ZX2. The car is very hard to start when cold and it runs extremely rough, but only through my first acceleration under load. In other words, I can rev the engine a few times while in neutral, and it will run very rough, and once I start driving, it runs really rough through my first acceleration, but then it smooths out and runs fine from then on until I stop it and let it call off for 30 minutes or more. If I restart it within 30 minutes or so, everything is fine, but any longer that that and the problem reappears.
View 3 Replies
My 98 Maxima won't idle without dying, it sputters when you accelerate, and it tries to die while coasting. I've changed two O2 sensors (AutoZone gave me the code for bank 1 sensor 1 & 2) changed spark plugs, tried fuel injector cleaner, oil change, and cleaned MAF sensor & checked the wiring. It;s still spitting out the black exhaust. Although after changing the O2 sensors it quit for about a day or two but started again (I'm guessing the other sensors need to be changed to) But the main problem is once it warms up, it really runs like crap, and is a major gas hog. I'm getting about 12 Mpg.
View 19 Replies
1998 Jeep Cherokee sport ... My mechanic tells me that my #1 fuel injector is always spraying and that that is why the jeep runs rough. This is after he already told me that my injectors were clogged and needed to be replaced (which he did). When the car is idling for a while, the exhaust really begins to smell like gas, so this seems to make some sense to me, unlike his previous diagnosis. But now he is telling me that I need to replace the computer to fix this problem.
View 8 Replies
My F150 with 175,000 miles on gave me a the ol' P0305 code indicating misfiring in cylinder #5. I changed the plugs and wires using Motorcraft wires and Motorcraft AGS34FM plugs.
Now the truck idles fine, does not give a OBD code but runs rough at 2,000-2,500 rpm. Tried it out on the highway and it started "bucking" a bit. Not sure what to try next.
View 2 Replies
I am going along and the power just goes away. Sometimes it is a 50% loss other times it is an 80% loss. I hooked up my scanner and found an IPR code. I replaced the IPR and connector, nothing changed.
As the scanner info shows the Duty Cycle and Pressure track about identically until something goes wonky. When I loose about 50% power the pressure will not get above about 1500 psi but the duty cycle will run up to 60%. Other times when I have a bout an 80% loss the pressure and duty cycle both track low, no more than 1200psi and about 20%.
View 14 Replies
98 5.0 last week i was driving around for a few hours and everything was fine. Did some work in the garage for a few hours and had to run to the hardware store. Started the truck up and she ran like crap. Engine shaking like a misfire. First thought plugs and wires. Well by then it was late and Easter was the next day didn't get to it till Monday. Well after the change still crappy running.
So I changed the fuel filter and cleaned the mass air. No change. Checked for spark on the coil packs all have spark. Checked the PCV all good there. Checked for vac leaks none found. During that I noticed a small hole in the EGR tube I repaired that but still running like crap backfiring out the exhaust, engine shaking badly at times. I also changed out the FPR on the fuel rail. No change of course.
As of today I changed the coil packs. Again no change. Only code it throws is a EGR high flow after I fixed the hole but was having problems before that.
View 10 Replies
2003 F350 6.0L ... 171,000 miles ... 5,100 since oil change 15W-30 at the shop ...
I was driving on the interstate (50 miles of driving) struggling to maintain 70-75 mph at 2,200RPMs. I would accelerate and RPMs would go up to 3,000 but no speed. Before I could pull off speed slowed to 50 before dying. Sat on the side of the road 30 minutes before I could get it started. Had to give it gas. No misfires just quietly started. Couldn't go over 30 mph. Towed it to my destination 135 miles.
Volts on 7Pin FICM read fine.
Checked the fuel fulters. Air Filter. Tank for debris. Nothing.
My coolant reservoir was lose and I noticed a lot of coolant in the driverside front wheel well and down the left side of the undertruck. Reattached after checking FICM. Hope that was all it was cause I couldn't find any leaks.
I had Planned to have the oil changed before the return trip before this all happened. New to Diesel engines but I like a challenge. Where do I go next?
View 3 Replies
Well, coming home from work Friday and my truck turned on the check engine light. I did not notice any loss of power or other driveability issues. When I got home I pulled the DTC's. I got P0264, P0273, P0276, P0279, P0611, and U0306. The first four being low voltages. The Second FICM. And the last cylinder 6 misfire.
I sent a message to Ed at FICM Repair asking if there was anything to check before I pulled the beast. He said no it needed service no matter what at this point. BUT, I needed to test batteries and alternator. So I spent some time today pulling off my FICM.
I went ahead and pulled the EBP sensor and tube off from the exhaust manifold. The manifold end was very clean. BUT, the sensor end had a noticeable restriction. I would guess a 40% restriction. I cleaned the tube and the sensor and put it back on.
Next I moved to the EGR. I pulled it off and it was dirty but not what I would call restricted. The valve moved freely. I cleaned it anyway and blew out the manifold before I reinstalled it.
I have the batteries on a charger right now. Once they each charge for 12 hours each I will let them sit a day or two before I load test them. They are about four years old, AC Delco 60 month 875CCA batteries. I have had problems the last 6-8 months with staring the truck. If she sits for more than 3-4 weeks without being run she turns over slow and won't start. So I have had to jump start her a few times. And before you ask I have done a parasitic check and only have .05amp draw. So maybe the alternator is getting weak.
On that note I pulled the alternator and will get it bench tested this week. While I was there I noticed the top grooved and smooth idler pullies were a little "wobbly" so I yanked them too and will replace. Might as well do the belt while I'm at it. Boy this is going to get expensive real fast.
So, I decided to go ahead and replace the bottom coolant recovery hose and the long hose/pipe heater hose too. Boy it never ends. Oh well. I would rather do it now while I have stuff pulled off and it is easier to get to. Ordered those parts from RockAuto to the tune of 219 dollars. OUCH!!!
I accidentally broke my new engine oil dipstick while I was trying to get to the FICM!!!! CRAP!!!! More money. So......... Is there anything else I might want to look at while I am there?
The truck is 2006 F250 6.0 PSD CC SB 4x4 mid optioned XLT with 108,000+ miles. I have a 4" turbo back exhaust, AFE Cold Air Intake, Blue Spring, Hypertec Power Program 3 on the lowest setting, and an after market intake elbow at the intake manifold and an engine oil bypass filter. Turbo was pulled and de-coked about 18,000 miles back. Otherwise no issues. The 90,000 mile service was done about 10,000 miles ago. She gets regular services.
How about methanol injection? Will that keep the intake clean from the EGR sludge? I'm not thinking about added power, just keeping things cleaner? I plan to do the Atlas 40 when the FICM gets repaired.
View 14 Replies
My truck runs very rough and lacks power when cold, even during the Texas summer. Once it warms-up, everything is fine. It's almost like turning on a light switch. If it's plugged in for a couple/few hours, it's smooth as soon as it starts. I'm assuming it likes the oil once it reaches a specific temperature. What my problem is?
View 14 Replies
After almost an entire year of trouble-free running (with the exception of replacing a ground strap), my 2009 accent decided to start bucking and shuddering again. It only does this when warmed up, runs perfect cold. In the last 16 months, I've replaced the plugs, coils, battery, PCV valve, and ground strap. Car starts with zero hesitation.
Strong battery and starter, consistent output from alternator. After @5 miles, the car stumbles on acceleration, and idles sporadically. While looking at it tonight, I noticed a few exhaust brackets under the car had broken, and the flex section of the intermediate pipe had torn open. Could this presumed exhaust leak be causing the crap running performance?
My "exhausted" brain thought it could cause the O2 sensor to misinform the ECM, resulting in the P0300 code I pulled...
View 3 Replies
My 2001 V70 24T runs smooth when cold as it warms up it runs rough with delayed acceleration reaction ....
View 1 Replies
I have a 1995 GMC that I have owned since new. It has 212,000 miles on it, a 305 TBI, and a manual five speed. It started running bad all at once. It idles rough, at different speeds and never settles down, (between 900 and 1300 rpm. It smells like raw gas, smokes, and has no power to get started from a stop. I checked the vacuum, it is at 19" at all rpms. The MAP sensor reads 0.3VDC when off, 4.12VDC when idling, and 1.5VDC at WOT. It appears to have 12PSI fuel pressure (after a messy test set up!) on the fuel pump side of the fuel filter (filter replaced 10,000 miles ago). The EGR valve appears to cycle OK when I suck on the vacuum line so I assume it works OK. I found a bad TBI flange gasket and replaced it. It runs slightly better but still smells like raw gas and has no power. When I try to accelerate, it immediately has no power, like a big vacuum leak. The idle is close to normal (900rpm = normal). Do I just start replacing parts?
View 9 Replies
I have a 04.5 GLI 1.8t, performance mods include, cone filter on the end of my maf, silicone TIP, Forge splitter, 3in custom tbe and unitronics stage 2
I started noticing this problem on the day I got the car tuned, I hadn't noticed it before hand. I replaced the spark plugs and it worked a little, but it continues to do it.
The problem: When I get on it at WOT under full boost, around 2500 rpms, the car loses all torque, misfires spits and sputters throughout the rpm range until about 5300 rpms then it all of a sudden has torque and pulls great.
I don't have any boost leaks that I know of along with vaccum leaks. There is no flashing cel or misfire code for my coil packs. Can this be a faulty n75 valve? if so what could fix it?
View 24 Replies
