I have 2009 tacoma pickup w/10k After starting fine and driving a few mins. and turning off it will not restart for aleast 10=15 mins. All the instr. lights come on like normal.....but it will not crank nothing? no starter noise ...nothing I contacted my dealer The service guy said (never heard that before)....
View 3 RepliesI have a 2003 Toyota Tacoma pickup. I bought it used in the spring of 2009. I drove it for a few months without any problems and one day this problem developed. It won't start on the first attempt. Or it will start and then immediately die. It will take two or three tries to get it running.
I took it in to my mechanic and he couldn't find anything wrong. I got a tune-up anyway and it drove like a champ. Until the next day when the problem came back. This persisted for a few weeks more and then went away.
This last summer it started happening again and continued up through October and went away again. I think the problem seems to happen when it's hot in the summer.
Truck has many issues, among them loose steering. I took it in for a checkup, and it needs a new steering gear. How difficult are they to replace?
View 1 RepliesI have a 2011 Toyota tacoma with 35k miles. Yesterday while driving at about 70-75mph on the freeway with no warning the vehicle shut down and the engine light came on. It made a clunk about the the time it shut off, it wasn't very loud but I could feel it. I'n not sure if that noise was just the vehicle powering down or transmission kicking from the change in torque? I pulled off the freeway, there were no fluids leaking, serpentine belt was in place. The truck will turn over but not start. The check engine light flashes rapidly.
View 1 RepliesI have a 1988 Toyota (4 cylinder) Pickup truck, with a very intermittent starting problem, that is driving me crazy. It has had the starting problem for over a year now. Normally is starts easily, within one second with the starter motor, no gas needed, and it starts smoothly.
When it has the problem, I turn key, and I only hear a click, and the dash lights are lit, but no starter motor sound.
Early on I would call for a tow truck, but it usually started when they arrived.
I got angry one time and turned the on and off rapidly, nothing. Meditated for about 10min to calm down. Nope, still angry, so turned the key rapidly again, and the starter motor engaged, but the engine didn't start.
So I did that again and gave it some gas, then a lot of gas. The engine was running very rough, like all cylinders were not firing, then it spews out a huge cloud of blue smoke, and the engine evens out. That's my usual pattern now: turn the key like crazy wait a few minutes or even an hour, and keep trying.
It is usually fine for 2 to 7 days with no problems. But a couple of times it has had the problem twice in the same day. The problem seems to happen most when the engine is cold, or after a short trip. A few times, it has had the problem even after a long trip, when the engine was still hot.
What has been replaced in the last year? In this order: starter motor, battery, hot lead to fuse box, battery terminal clamps and wires, fuel pump, mass air flow (don't know what that is), catalytic converter, and master relay. (OK the master relay probably isn't related because rain water leaked in and dripped on the fuse box in the cab.) (Also it has 133,080 miles, and a rebuilt engine put in 4 years ago.)
After the mass air flow and catalytic converter change, the truck has started with no problems for 3 months. Now the problem is back! Same symptoms.
When they last worked on the truck they did a tune-up and they said the starting problem could have been caused by the starter motor not being lined up properly so it would "jam". That would explain why the starter motor wouldn't go, but it doesn't explain the miss-firing when it does finally start going.
I also notice that after they do some work on the truck, it starts fine for about 2 weeks with no problem. So maybe something is getting wiggled into a happy position when they work on it?
If this is an "electrical" problem, what can be done to find this very intermittent problem? Also, just before the the problem started happening again, I noticed there would sometimes be about a 1/2 sec to 1 sec delay from when I turned the key, to when the starter motor would go.
Attached is an audio file of what it sounds like.
1) starting normal,
2) turning key and only clicks,
3) the rough start after many tries.
I have a a 1995 GMC Sonoma 5-speed 4 cylinder pickup. When I drive this truck for any amount of time and turn it off for a few minutes (0 minutes - 1 hourish) the truck runs really rough for the first minute and almost dies. Then it will start running normally again after I've putted down the road a block or two. A couple of times this truck has died completely after running rough and won't start again for almost an hour afterwards.
View 1 RepliesTwo wheel drive, small engine with two spark plugs per cylinder...clutch with five speed transmission. Over two hundred thousand miles on it. Drove it thirty miles on a rainy evening. Shut it off for about one hour and when I tried to restart, it just went click. Got towed thirty miles home. Replaced starter with brand new one and also new battery. Still nothing but click-click. Does start from clutch engagement when rolling. The trouble seems to be somewhere between the starter and the battery. What to do?
View 3 Replies I have 2009 corolla with 70000 miles on it. I replaced new brake pads. I have some metal grinding noise when i turn right only. I tried looking online and got few similar problem faced by other people. I am not sure if its exactly same issue. No accident damage. Mostly driven on freeway.
1) noise looks similar
2) I do not get noise when i accelerate
3) for car this old is it expected ?
I have a 2009 Toyota Camry with approx 124K miles on it (my daily commute isn't that great...). Lately I've noticed some vibrations or rubbing when I'm turning:
There is a constant rubbing/grinding noise when turning. It is more obvious when I turn right. It is definitely coming from the front tires. It does not sound like metal at all. Just like a rubbing noise, that causes a slight vibration up front.
When I'm driving straight, at a certain speed, I notice the vibration/rubbing sound, but it eventually blends in with the sound of the road. The ride isn't bumpy at all, so I don't think it's related to the struts. When I pull out of a parking place, turning left, it just feels "loose", if that makes any sense.
From what I've been reading, it seems to lean towards a bad wheel bearing, or CV issues. What the problem could be?
I've offered to do a basic compression check on a 22R engine, '85 Toyota pickup, which is apparently low on power, won't go above 50 mph. Yes it could be a multitude of things. Chances are it's several of them.
I have not yet heard it run. I'll consider myself lucky if I hear the uneven cadence of running on three cylinders.
My job Tuesday is to screen it for the most obvious things like a clogged air intake or air filter, choke stuck closed, worn spark plugs, etc, and do a simple compression test. I will again try to persuade the owner to take it to the skilled mechanic I've recommended, which he has resisted thus far, even though he's about to set off on a long trip through desolate terrain.
I already suspect low compression based on what the owner has implied, but also wondering about ignition timing and vacuum advance. This is a carbureted engine, so does that mean that it also has a distributor and needs to have the timing set? I have a timing light, but only vaguely remember the procedure...disconnect vacuum line from carb and plug hose leading to distributor? Any marks on the harmonic balancer to align?
Evidently it has a bogus exhaust system too - no cat - making me wonder if there's a problem there. I'm not going to get too deep into this, but if I can at least spot the problem I want to be able to convince the owner that there's a clear explanation, so he'll get it resolved.
have an 2009 Toyota Corolla 62K miles. If the car sits out 8 hours or more in VERY COLD (zero degrees) weather makes a 1-2 second clashing/sparking noise the split second after turning the ignition on but before engine starts. I tried to attach video/audio. The car starts and runs fine. isn't a ticking or knocking or tapping noise assoc. with bad engine. It isn't squealing noise assoc. w/ serpentine belt. I've been waiting for it to get cold enough to leave overnight at Toyota dealer. I keep wondering if it isn't related to the botched oil changed at the Toyota dealer a couple yrs ago when they forgot the oil & I ran car about 30-60 seconds. At the time, they said all was okay and did compression test (Cyl 1=178psi, #2=175 #3=180 #4=178) all within the normal specs 145-189. I got a 2nd opinion at another Toyota dealer at time who removed valve cover and inspected cam caps and scoped cylinder walls and said all was okay and compression good. No mechanical problems- uses no oil, check engine light not on, etc. What noise is and why just when very cold and car sits out long time?
View 18 RepliesI have a 91 Toyota pickup. Few weeks ago setting in drive through truck quit when I turned on a/c. This happened coup,e times then next time I drove it ran fine. Then it stopped two days in row after driving 20 min. Truck would crank but shut down immediately. Waited few minutes and cranked and drove home no problems. Now truck will only run few min. Before stopping and if I turn on fan or lights the truck stops. Swapped battery from another vehicle but did not fix. Alternator seems to be charging fine, checked with meter output 14.5 volts charging. Checked for codes and no codes.
View 2 RepliesMy 1992 Toyota pickup (138,000 mi) started popping out of first gear today. How big of a problem is this and what needs to be done??
View 4 Replies'91 Toyota 2wd Pickup, 22R-E Engine. 1 yr. ago out of the blue it would start and idle, but if I give it any gas it would die. Shop had trouble figuring it out, then replaced Mass Airflow Sensor; problem re-occurred after once after this repair, but could not be reproduced at shop. 1 yr. later, driving along and engine quits without any warning. Very hard to start, but restarts once, drives about one more block, dies. Unable to restart; engine will crank and catch, but after about 1 second dies. Tried unplugging Mass Airflow Sensor; no change. Left sitting overnight, next morning it starts right up. Problem seems similar to a year ago, though this time it wouldn't start and idle, it would just start and immediately die. In every instance it was rainy/slushy and cold.
View 8 RepliesI have a 1986 Toyota pickup. It's small 2 wheel drive with a stick shift. 6 weeks ago, it started lugging very slightly on hills after I had first started the car (only in the first 5 minutes of driving). Then that stopped, and now it loses power on hills so that I have to keep shifting down and going slower until I'm chugging uphill in 2nd gear at 30 mph. It only happens on long hills with a sustained uphill; smaller ones it keeps speed and power fine.
View 2 RepliesI recently had a new engine and radiator installed in my 1993 toyota pickup. I checked the coolant and oil every day since the install, then drove it 250 miles or so without checking the coolant, and found that all the coolant was gone from the reserve tank, and there was a sludge at the bottom. I don't see any leaks, and the thermometer indicator was normal.
I don't understand where the coolant could have gone, given that it's a totally new motor and new radiator, new hoses. I'm worried about the competence of my mechanic, not noticing a dirty coolant reservoir and maybe messing something else up.
When adjusting valves on a 1986 22RE Toyota engine, the manual says to adjust intake to .008 and exhaust to .011 when the engine is "hot". I was doing some research and it seems to be a somewhat common practice to adjust valves on these engines to .007 intake and .011 exhaust when the engine is cold. The explanation being that the clearances will open up some when the engine warms up or gets to "hot". I always thought the clearances would get tighter as the engine warmed up but my "knowledge" is based on traditional pushrod engines and this is an overhead cam engine. If adjusted cold, will the clearances get smaller or larger when the engine is hot? And is it ok to adjust the valves cold? And how hot is correct amount of hot if I adjust them according to the manual?
View 11 RepliesI drive my pickup (87 Toyota 4-cylinder carburetor 5-speed Xtracab Deluxe) occasionally. When it's sat for a week or more it takes a few tens of seconds to start. I bought a booster battery. The charging light comes on, but it goes out as soon as the engine starts. I'm used to hard-to-start cars charging for a while after a long start. The voltage coming out of the alternator is okay. The battery is new; the density of the electrolyte is right.
View 19 RepliesI have a 1990 Toyota pickup. I've been told to always put the brake on when I park. The brake is a hand lever under the dash that I pull out and then to release, I push a button, pull a little and then push. Yesterday I got into the truck and went to release the brake and it was stuck. I had my foot on the brake, and it was in 1st which isn't out of the norm for how I start the truck. I did notice that the handle seemed loose. I eventually got it back in after starting the truck again and putting it into first and trying to pull forward with the brake on. I'm concerned that if I use it again it will stick again and not go back in! What has happened!?
View 5 RepliesThe temperature gauge on the dashboard is jumping around after the car warms up. It rapidly goes from cold to normal in an unpredictable pattern. It never goes over the middle. I have had both the engine and the radiator replaced in the past year!
View 3 RepliesWhen I turned the key to start my car, I got zero activity from it. No ticking, no lights, nothing. So I tried to do a push start, and the engine wouldn't engage. I took the key out, and suddenly my dome light popped on (though it was dim). I put my key back in and turned it, and dash lights looked normal and at full power, but as soon as I pressed the clutch down and tried to turn the key, everything went dead. I took the key out, put it back in, and turned it, but got nothing.
I pushed my truck up to the top of an incline, and turned the key. All the lights looked normal, so I thought I may be able to push start it. Key was in proper position, clutch was engaged, and gear shift was sitting in first. I got a decent speed, released the clutch... and everything went dead.
I can't decide if it's my starter or my ignition system, though I suppose it could be the wiring, or even something else.