Toyota - Sienna :: Brake Pedal Goes To The Floor And Car Does Not Slow Down
Oct 23, 2006
My Sienna 2005 experience intermittent complete brake failure 3 times within 18,000 miles,the brake pedal goes to the floor and it does not slow down, so I coast until I stop. However, when I release the brake pedal and then reapply the brakes, it works fine. A non-Toyota mechanic thinks it's due to malfunction of ABS. The dealership is unable to finds error codes and brakes work fine when the Sienna is in their hands. I scared that the brakes will not work the next time I reapply the brakes.
View 30 Replies
Advertisement
M friend with his 98 gmc. When stopping the breaks are normal until getting slow then the abs motor comes on and the break pedal sinks to the floor. The truck stops but the abs motor runs constant until you release the pedal. This is happening on dry roads. What is there to check before condemning the abs module?
View 4 Replies
My 1987 toyota celica brake pedal is going to the floor when I apply the brakes but not all the time,i checked the pads and shoes they are still good i also bled the brakes, I am thinking it is the master cylinder or maybe the master cylinder needs to be bled.
View 1 Replies
So, until recently I had a 2000 Ford Focus but it was totaled in an accident not long ago and is long gone now. I was given a 1985 Toyota Tercel Wagon with about 194,000 mi by a family member. However, it has always had a problem whereby the brake pedal goes to the floor now and then and especially when it is cold in the morning. So, I took the car to a mechanic (hwy 64 auto, Raleigh, NC) and they replaced the Master Cylinder yesterday and bled the brake lines through the master cylinder.
The mechanic told me that the bleeder valves were too old and corroded to try to bleed them at each wheel and that they might break and then the caliper(s) would then have to replaced. Anyway, long story short, the brakes are WORSE after he changed the master cylinder and bled the lines from the master cylinder. Now EVERY time you first press the brake the pedal goes down then immediately you can "pump" them back up so either air in the lines or still a leak somewhere in the braking system. I do not want to spend anymore money (or at least very little money) on this car as too much has already been spent on other things before I got it and also after I got it.
Did the mechanic screw up or am I looking at a problem you have with some old cars where you start replacing parts in the brake system and then still have the problem or a new problem and then you wind up spending $800 replacing old crappy, worn out parts. What should I do? Did the mechanic screw it up or is it just time to send this old car to the scrap pile and crusher? Remember, I don't want to keep pouring money into this thing. I've already spent some money on it with other stuff lately.
View 19 Replies
We had our Timing belt& water pump replaced 5 months ago, due to maintenance book suggestion for our 2006 Toyota Sienna LE, 119,000 miles on her. Now there is a leak in the R & P.
View 2 Replies
I have a 2002 Toyota Sienna van. My garage failed to check the brake shoes as requested, so I gouged the back brake drums and had to have them replaced. Shortly afterwards, whenever I brake, in the last 2-3 seconds before I stop there is a thumping noise from the right rear wheel. It will thump a few times, maybe 2-5 times, perhaps one thump per wheel rotation. I don't feel any pulsing in the brake pedal, and except for the noise braking seems normal. Could this be due to the shoe adjustment being too loose, so the shoe has room to pulse inside the drum?
View 2 Replies
I have owned a 2006 Toyota Sienna for about a year and half, it has 180,000+ miles on it. Periodically and totally unexpectedly, we'll go over a bump in the road and the van will totally lock up like I have pulled the emergency break up. Which I haven't. The van will still be in drive, the tires will come to a complete stop and we'll have see and smell burning rubber.
To get the car going again, we'll have to put it back into park and then back into drive. Its one of the scariest things I have witness being in a car. Luckily it usually happens between 10 -20 miles per hour and we haven't had an accident because of it. I have taken the van to 3 mechanics including a Toyota dealer and no one has been able to fix it. The only thing that has work for a time has been cleaning the speed senors, Also, it maybe worse when the A/C is on but we aren't sure.
View 14 Replies
I was driving around today and had to hit the brakes really hard for the first time. ABS kicked in and during the ABS 'action' the brake pedal rapidly went to the floor. With each 'pump' the ABS made it felt like the pedal sunk slightly.
This was on dry pavement, a little gravelly / dirty and the car stopped rapidly, but just as I stopped the pedal was VERY close to the floor, and with just a touch more pressure it did in fact hit bottom.
Sounds to me like the ABS pump needs to be bled, is that right? Can I do that myself with a VAGCOM? I hate having the dealer do anything, even if it is their job. How to SAFELY confirm if cars does / does not do this as well?
View 8 Replies
Tonight our 2002 Toyota Sienna (automatic transmission) was in drive, but stopped (foot on brake) during a traffic jam. Traffic picked up and the driver moved his foot from brake to gas. The car went into reverse at a high speed. The brake did not work. The driver quickly changed gears to park.
1. What is (are) the problems resulting in this situation?
2. Has additional damage been done by switching into park?
3. Is it safe to drive to the repair shop?
View 1 Replies
2005 Volvo S60 T5, 90,000 miles. The brake pedal depresses almost to the floor. Dealer service has not had a solution to this problem. All brake components are supposedly nominal. Might pedal position sensor be faulty?
View 1 Replies
My 04 Camry is having brake issues. It has 205k miles. The front pads are great and the back shoes are great. (Drums in back) I've had them adjusted multiple times but my pedal still goes almost to the floor. It's not the master cylinder cause I've already replaced that. The pedal doesn't bleed off either. But I have bled the brake lines and there is no air left in the lines.
View 14 Replies
My mother went out 2 days ago to go run errands, she stepped on the brake pedal and it went to the floor (car still in garage and in park, low mileage car 81,xxx garage kept). I have not been able to duplicate the issue. The fluid has been changed twice since new, no signs of fluid loss, undercarriage inspection revealed nothing. I am thinking maybe a vacuum hose issue.
View 2 Replies
When I go to start and depress the brake pedal it goes all the way to the floor. The brake fluid is at the full mark and my 2011 has only 25k miles. Where should I look since it did not go all the way to the floor when I forst got it with 6K miles.
View 19 Replies
I drive a 1991 F-150 Lariat Extended Cab. Out of the blue, my brakes decided they didn't want to work unless the pedal is about 1/2 - 3/4 of the way down to the floor. As soon as I release past that 1/2 mark, they shut off. While this makes it great for tailgaters, it does not make it great for police officers.
We have already replaced the switch thinking maybe it was that, but alas it was not. I was reading in a couple difference places about the multiswitch? However, the symptoms other people had were similar, but not the same. I never tilt my steering wheel, so I dont know if that's the issue!
View 2 Replies
2013 Prius c Two, bought brand new with 15 miles on it 5 weeks ago. A few times when driving, I noticed the brakes seemed weak, like they weren't stopping the car very well even at low speeds (My driving is mostly in town on residential streets, so I'm rarely going over 35 MPH. Even so, I'd have to really mash the pedal all the way to the floor to get the car to come to a complete stop, otherwise it would keep moving forward. Several times I ended up about 5-10 feet past the line, sticking the front bumper into cross traffic. Luckily no one hit me. I chalked it up to the quirks of a different car than the one I was used to, and figured if it kept happening I'd take it to the dealership.
On Monday, my wife was stopped at a red light. The light turned green and the car in front of her started to move forward. After a few hundred feet, he suddenly slammed on his brakes. She said her brake pedal went all the way to the floor, and the Prius didn't slow down at all. She hit him going about 25-30 MPH and totaled the Prius. She's an excellent driver and I've been with her before when she's had to panic-stop. She's never driven a car without ABS, so she is used to pushing the pedal hard and keeping her foot on it. She wouldn't even know how to "pump" the pedal. She swears the pedal just went all the way to the floor and the car didn't slow down at all.
View 18 Replies
For the past several weeks, my daughter reports that she has to put her foot almost all the way to the floor to get the brakes to work. The brakes do not have an effect until her foot is 1-2 inches from the floor. It usually happens after she has been driving for a while without pressing the brakes. I’ve driven the car numerous times but haven’t been able to replicate the problem. Her commute is approximately 10 miles each way in stop and go traffic. The car is a Volvo xc70 with 200k+ miles. I've had it looked at by a mechanic who didn't find anything but it's continuing to happen. I'm suspicious that it may be a master cylinder problem and concerned about complete brake failure -- should I be?
View 7 Replies
When I press the brake pedal, the car will stop. But if I keep pressing it while the car is stopped, the pedal wants to keep going towards the floor. I have to press hard for it to do this. I have bled the brakes. I've checked the calipers and the hoses for leaks and don't see anything. The master cylinder is topped up and I don't see any fluid underneath it. It doesn't appear to be leaking. The funny thing is, when I turn the engine off and press the pedal, the pedal comes to a stop and doesn't want to move after I pressed on it as hard as I can.
View 2 Replies
I have a 2007 Sonata GLS 4cyl. Anyhow lately my brake pedal is going right to the floor. The brakes seem to work fine, but if I keep constant pressure on the pedal it will slowly go all the way to the floor. My rear rotors and pads have been changed a couple of months ago and I'm pretty sure my front brakes are good. What could be causing this? I also checked underneath the car for leaks and there doesn't seem to be anything leaking underneath.
View 6 Replies
I have been working on my 01 Elantra for 2 days now. My problem is that I have absolutely no brake pedal at all, it just goes right to the floor. and this is only when the car is running, when it is off I give it a quick pump and i have a nice firm pedal. I installed a new master cylinder, bench bled it and all that jazz. I replaced the rear brakes and a wheel cylinder, I have also bled the brakes multiple times, and mutliple ways. bled the master while on the car and all the brakes while the car is off and while it is running. I dont know what else could be wrong with this. I looked at all the lines and there are no wet spots, no hoses are swelling up. everything looks top notch...i just have no brakes why.
View 15 Replies
I have a 99 Blazer 4x4 with ABS. Brake pedal just went to the floor and car stopped eventually ... a bit scary. I've checked all the brake lines and the inside of all wheels and there is no sign of fluid anywhere. All pistons seem to be where they need to be with backing plates nicely visible.
I pumped the brakes quite a few times and same result ... but I'm not pumping fluid on the ground. As expected I've also checked the reservoir and its full. Didn't see any leaks so its full. I'm guessing that the master cylinder has given up the ghost ... truck has 470,000km so things wear out.
View 5 Replies
A friend brought me a car with the issue that the brake pedal sinks to the floor when braking. She said it was never low on fluid so I replaced the master cylinder and bled all of the lines with a friend pumping the pedal. The pedal would still sink to the floor. I tried vacuum bleeding the brakes and found that the front left consistently had large bubbles.
I Teflon taped the fitting on the calliper and the bleed screw which improved the problem but didn't fix it. I then replaced the calliper. The front left calliper still won't bleed and the brake pedal still goes to the floor. When I bleed it the regular way, the fluid comes out of the bleeder like it bled nicely. Neither of the rubber hoses that connect to the calliper have any visible damage. I had a friend pump the brakes while looking at the hoses and their is no bulge or swelling in them. Could the ABS need to be bled?
View 4 Replies
