Toyota - Pickup :: 1985 - Stalling When Put The Truck In Neutral Or Don't Shift Quickly Enough
Feb 20, 2013
My 1985 Toyota Pickup (manual shift) is stalling out when I put the truck in neutral or don't shift quickly enough. The battery light comes on after stalling followed by the oil light. After stalling, it does start back up and repeats the same problem. If I keep my foot on the gas and the truck in gear, it runs. I'm new to DIY repairs, and bought this truck for the purpose of learning more. I know the basics, am mechanically inclined, have a repair manual, and am a quick learner.
View 4 Replies
Advertisement
I've offered to do a basic compression check on a 22R engine, '85 Toyota pickup, which is apparently low on power, won't go above 50 mph. Yes it could be a multitude of things. Chances are it's several of them.
I have not yet heard it run. I'll consider myself lucky if I hear the uneven cadence of running on three cylinders.
My job Tuesday is to screen it for the most obvious things like a clogged air intake or air filter, choke stuck closed, worn spark plugs, etc, and do a simple compression test. I will again try to persuade the owner to take it to the skilled mechanic I've recommended, which he has resisted thus far, even though he's about to set off on a long trip through desolate terrain.
I already suspect low compression based on what the owner has implied, but also wondering about ignition timing and vacuum advance. This is a carbureted engine, so does that mean that it also has a distributor and needs to have the timing set? I have a timing light, but only vaguely remember the procedure...disconnect vacuum line from carb and plug hose leading to distributor? Any marks on the harmonic balancer to align?
Evidently it has a bogus exhaust system too - no cat - making me wonder if there's a problem there. I'm not going to get too deep into this, but if I can at least spot the problem I want to be able to convince the owner that there's a clear explanation, so he'll get it resolved.
View 19 Replies
I have a 1985 Toyota Tercel that I just got, the thing has been sitting for 2 years and it started before it was left to sit. Now I have done all the usual maintenance on it, replaced the sparks, oil, oil filter, air filter, distributor cap, fuel pump and fuel filter, gave it some gas treatment and filled the tank and some carb cleaner to clean out the gunked up carb. My problem is that it starts but dies right after when it tries to idle. it can shift in to gear and such but it will still die out right after about 10 seconds unless I keep tapping the gas. The more times I start it the longer it stays idle but I wonder what the problem is...
View 4 Replies
I own an 85 toyota pick up. It has a 86 electrical system with a 95 engine. To date, this truck has run like a top until I got in the other day and turning the key nothing happened. That is to say, the starter did not turn or kick out. I had the starter tested and it is fine, I tested the starter relay and the neutral position switch. All the wiring checks out fine except for one That comes off the starter relay in the fuse box under the hood.
This wire seems to be a ground for the coil side of the relay. In my books, it should go to a clutch /start switch that I can't find. When I follow the wire it goes from the fuse box into the right side of the engine compartment into the fender area then runs toward the cab but I do not find its color combination going into the computer. I had this same problem with a 86 truck before and never found the problem.
View 1 Replies
My 94 truck (Toyota 6 cylinder 3VZ engine) is currently idling at ~2000 when I first start the engine. After warming up or driving for a substantial amount of time, this eventually drops to ~1000-1100. I had the throttle body removed and cleaned (twice). This stopped some up-and-down revving which was happening, but not the high idling. This is a relatively recent development, and I've gone to 3 mechanics AND the dealer, all of whom say, 'it's fine'. They say it should run 'a little higher when it's cold'.
I think some of these assessments were based on the simple lack of engine error messages (no codes from the computer = no problem). I admit that I'm no expert, but I've had the truck for a decade; I know what's 'fine' and what's not. The usual idle was ~800 (in agreement with specs) and I've driven this truck in temps down to -30F. It has never idled this high before. Since it gets close to normal RPMs after warming up, I don't want to turn the idle adjustment down. I moved from a very cold, very dry climate at 6000 ft to a very wet, moderately cold climate at sea level - is there some other adjustment I need to make? Or is it normal for this engine to run so differently in these two climates? I'm at the end of my rope since no one thinks it's a problem except me.
View 1 Replies
My ranger has always run pretty good except for a small bit of chattering at startup which quickly went away after it warmed up. Now all of a sudden its much louder and doesnt seem to go away while driving. I read about the oil pickup tube getting blocked and not properly delivering oil and so I performed the superhuman task of dropping the oil pan to check. While I couldnt get the oil pan all the way out, I got it to where I could feel the oil pick up screen and everything seems okay. I have the valve cover off. Are the lifters adjustable? Whats the issue?
View 10 Replies
My Daughter owns a 2000 Camry. It has a very annoying habit of not starting when it is warm (think driving to the gas station, turning the car off to fill it and then it doesn't start again). We have tried new solenoids, a new starter and several other tweaks but nothing seems to fix the problem. Recently she discovered if she jiggles the gear shift lever (it's an automatic) it will start. So, obviously she gear shift lever is not finding Park or Neutral so that it can be in position to start. She has experimented with this concept and it appears to be the only thing that consistently solves the starting issue. What would we have to fix in the gear shift lever, or elsewhere, to fix this problem?
View 5 Replies
This problem has plagued my '85 Tbird Turbo Coupe for about a month. When I put my car in neutral while moving, the RPMs fall significantly below idle and then the engine usually catches itself and after about 5-10 seconds idles normally. If I do this at high speed (say 40 mph +), the RPMs fall to the point where the engine stalls and dies. If I do it at 25-40 mph, it will go down about 200-500 RPMs and then catch itself. If I do it at 15-20 mph, it will be just barely noticeable, and anything slower than that I can't notice it. It will also do this to some extent when I'm stopped if I rev the engine up really high and let it off, but it is far less noticeable. This car has had extensive work done to it in the past 6 months.
Most recently, I had the fuel injectors replaced, throttle body cleaned, IAC valve cleaned, and the vehicle searched for vacuum leaks. (most of that in search of the solution to this problem as well as to improve the general performance of the vehicle. A week before that, I also had a new fuel tank, fuel pump, and fuel filter installed. I've got a very small leak on the back of my muffler, no cat, and no other exhaust leaks I can find. I am getting a lot of black carbon out of the exhaust, but I have been running some fuel system cleaner through it. Also, the car sat for like 8 years before I got it, and the original cat became clogged and really gunked stuff up. I had all of the upper engine gaskets replaced, as much as we could get to cleaned internally, and the cat cut off at that point. Timing is very close to 10btdc. Could be 9.5, but just about right there. I double checked, no vacuum leaks that I could find with a can of carb cleaner. I tried checking for codes, but it's not even throwing me a confirmation code or anything, which is odd. But, my connector was pretty gummed up (I did clean it as good as I could) and just about anything wiring is suspect. I used two engine code readers that had previously been used on the car. Other than this, the car has plenty of power and runs fine down the road.
Here's the master list of what I've replaced in the past 6mo:
FUEL SYSTEM Fuel Pump (twice) Fuel Pressure Regulator Fuel Tank Fuel Injectors
ASSORTED FILTERS Fuel Filter (twice) Air Filter Oil Filter (several times) Oil Filler Cap PCV Valve
HOSES/COOLANT SYSTEM Nearly every Vacuum Hose Every Coolant Hose Heater Core (twice)
SENSORS AND COMPUTER STUFF Engine Control Module (ECM) Vane Air Meter (VAM) Idle Air Control Valve (IAC) Oxygen Sensor
STARTING SYSTEM/ELECTRIC/Misc. Spark Plugs and Wires (Motorcraft) Starter Solenoid Coil Pack Distributor
TFI Module Distributor Cap and Rotor Battery Timing Belt
EEC Relay Ignition Switch Tires Front Brakes Brake Master Cylinder (had previously been damaged) Front tie-bars Every gasket from the head up.
View 11 Replies
So my dads truck is a 87 2.2 throttle body 4cyl and it cuts out and dies while accelerating and I have no clue what is going on we are thinking bad fuel filter or starving for air....
View 1 Replies
Toyota truck rv 1991 sun rader ... Sometimes our little rv gets stuck in park. We rock it back and forth, move the wheel all around, check fuses and fluids, and sometimes after 20-90 minutes it will shift again. Also our speedometer and odometer don't work, not sure if they are related !!
View 1 Replies
While lifting my 2003 Mitsu. Eclipse (manual) to replace a sway bar link, i was also checking on some other things and had the car running. It was in neutral yet the tires were spinning fairly quickly, and I dare say more on the driver side than the passenger side. Obviously this is a tranny issue, so I want to figure out what's going on pretty quickly. A quick note- depressing the clutch stops the power transfer completely.
View 3 Replies
Got a problem that has left me in circles. 85 BMW 325e, manual. Won't start. Previously had some driveability problems, sporadic brief stalling. Using the key in ignition switch, starter spins the engine with no hint of a start.
1. IGN components all test to spec and during start attempt there is spark on all cylinders.
2. Fuel flow and pressure is within spec, both when FP relay is jumped and during start attempt.
3. Speed and reference sensors test good.
4. All inputs to dme have been tested, including power and grounds, and are good.
View 19 Replies
I am fairly new to this stuff but I just got a 85 Ranger 4x4 and its running pretty rough it will be fine then all of a sudden it will bog right out and want to stall so I have to keep my foot planted on the gas and it pops and spudders and eventually runs normal again? Its a 2.8 V6 carb...
View 14 Replies
A little background. I was changing the oil and oil filter and noticed that the battery post was corroded. Disconnected the battery and cleaned the post. After that, I have noticed that most of the time, whether hot or cold, the engine cranks normally, quickly looses rpm to the point of almost stalling then recovers and runs fine after that. No check engine lights on at all. I have since removed the battery connections and waited about 5 minutes and reconnected them, turned on the ac, lights, anything that would put a load on the engine and cranked it hoping that it was just a computer problem. Nope, same issue. Truck runs fine otherwise, just the start up issue. Engine is gas powered 5.4 liter V-8.
View 2 Replies
My standard 2002 accent is undriveable and at the mechanic right now (100,000km). For the past few weeks the car has driven very jerky. While in first and second gears if i accelerate too quickly it just jerks/slips and has very little power.
Yesterday the check engine light came on and i got codes P0300, P0302, P0303...misfire in cylinders 2 and 3. Checked this forum and decided to buy new spark plugs (last replaced plugs and wires 1.5 years ago). Got into the car and could go more than a block because it was jerking and then kept stalling. Replaced the sparkplugs and nothing changed. Had it towed to the mechanic...after a few hours he said he had cleaned the exhaust manifold and it was driving fine. I picked it up and a block away it stalled again.
The mechanic now says 3 of my fuel injectors need to be replaced and the fourth will probably go soon and it will be about $700 to fix. Does this sound right for these codes?
I called hyundai parts and they told me each injector is $236...he also told me he doubted they had to be replaced cause he has never seen an accent have fuel injectors replaced and also they rarely sell these injectors, he said it was probably something electrical.
I have found 4 injectors on ebay for $200 but is this really the problem? The mechanic says it is 100% the problem. But from reading the forum I dont think so.
Also wanted to add that i often noticed the smell of burning plastic. Smoke seems to be coming from spark plug area when i notice the smell but nothing looks burnt/melted.
View 14 Replies
My 1985 BMW 635, standard transmission suddenly developed shifting problem. It will not shift into 1st, 3rd or 5th gear. It will shift into reverse,2nd and 4th gear. The car is not driven on any frequent schedule, infrequently. I can't remember the last time the transmission oil was changed.There has not been any mechanical distress,grinding of gears,etc. you just cant engage those gears. They all are moving the shifter from neutral to a up position. Is it possible that sludge could be blocking the movement of the synchronize r?
View 2 Replies
My 85 300 cid with a C6 trans won't shift out of first. Seems like this happened several years ago and it was a vacuum diaphragm or something like that. Is this user fixable or do I need a transmission shop to look at it?
View 2 Replies
I have a 1996 Chevy pickup with a 5.7 motor. I pulled the plug, oil is draining and I usually lift the hood; but this time I didn't (don't know why). Something came up and we had to leave quickly and we jumped in the truck and got 1/8 mile down the road, I pulled the plug on the oil. Turned around and parked it - the oil filter was still in - so there should of been some oil in there!?!? Do I need to be concerned that I damaged anything?
View 10 Replies
Well I Took my truck (1985 F250 6.9L IDI C6) and went through a little mud bog got some water in the tranny, no biggy i flushed the fluids out a couple times and went to drive it. But now it wont shift from 1st to 2nd but i can manually shift it from 1-2 I replaced the Modulator and that havent made a difference. Is there anything I should look into?
View 14 Replies
My 1970 chevy c10 pickup is a 350 with automatic transmission 2wd. It doesn't get driven frequently and when I do the first time I put it into gear, fwd or reverse, it is slow to engage. Shortly after it has warmed up however, this problem goes away. What this sounds like?
View 6 Replies
I have a 1985 Cadillac Fleetwood Brougham. I bought it from someone who had it sitting for a couple years and the fuel pump needed replaced, no problem. It ran fine for about 2 weeks after getting it fixed, then it started giving me problems. The transmission seemed to be having issues shifting gears at lower speeds, but acted fine once I got up to 55+. The mileage dropped from 16 mpg to 4 mpg. It started stalling out whenever my foot wasn't on the gas, and then finally it quit running altogether.
I had a mechanically inclined family member take a look and he said it seemed to be starving for gas but other than that he had no idea, it tries to start but can't turn over. In the past year I have had the fuel pump, fuel filter, air filter, and fuel injectors replaced but I'm not sure what else to look at. I'm hoping it isn't the transmission, we all know how expensive those are.
View 3 Replies
