Toyota - Corolla - Fuel-economy :: 2005 - P0171 Check Engine Code / System Too Lean
Mar 29, 2014
I have an 05 Toyota corolla, and have the check engine light on, I scanned it at autozone and error code is P0171 - System Too Lean (Bank 1). Which shows following possible causes: Faulty MAF, O2, fuel injectors blockage etc. On recommendation from the guy in autozone, I added fuel additive to clean the fuel line/ injectors. The check engine light went away for 9 months. But it is back on again. Tried putting in fuel additive again but the light remains on.
View 5 Replies
Advertisement
We have a 2003 Passat 1.8t. Had the Check engine Light come on. Went down to AutoZone and hookeded up the OBDII reader. Came up with P0171, Fuel System for Bank 1 was too lean. Probable causes:
1. Fuel Pressure of MAF (If Bank 1 & Bank 2 set codes together)
2. O2 Sensor
3. Ignition Misfire
4. Fuel Injector Problem
Car has 60K - has always run well. Wife says she thinks it's running a bit sluggish. I rarely drive the car, but I think she's right. Car is not missing or running rough.
I cleared the code & started the engine; Check Engine Light is off; then looked at the codes and I find a P0171 (Pending). She tells me that the light has been on before & then gone away. So I guess it clears itself, but eventually comes back.
View 10 Replies
My wifes 2007 Santa Fe Limited 3.3 has had a check engine light going on a year now. Car has about 122k on it now. Scanned codes about 6 months ago and had a fuel system lean code. Did some reading and ended up replacing the purge valve. The CEL stayed off til the end of the drive cycle and came right back. I have noticed when you fill the car up there is a real strong smell of gas but the car always starts right up. It now has a P0171 Fuel system too lean (b1) and P2187 Fuel system too lean at idle. Where to start. Don't have much background with hyundai. Also the ESC off light comes on randomly and goes off. Doesn't happen real frequently though.
View 4 Replies
I just bought a 99 f150 and the check engine light came on with code p0171,system too lean bank 1. It runs and drives fine but has a strong smell of gas when I shut it off.
View 4 Replies
I have had 06 passat with a 2.0 turbo. It been a great car. check engine light has come on with a few codes.
P0171 lean air fuel mixture. P2015, p2008, p0507, p2015, p2008.
View 4 Replies
2000... I have a code P0171 bank 1 too lean. My question is does this exclude anything that will effect both banks? If it was MAF sensor or fuel filter would it set code and say banks 1 and 2 running too lean? In which MAF sensor ohms out correctly. I cannot view fuel trim files. I have looked for a vacuum leak with no luck. I got some cigars to try to smoke it to see if there is any vacuum leaks. Trying to narrowing what i need to checks.
View 19 Replies
I have a 2006 Chevy Trailblazer LS/LT 4.2 liter 2wd. I have been trying to get it smoged, but can't clear the code. P0171 - Lean Bank 1.
I've been having a parts throwing contest with it, but it has been winning and my wallet is losing.
I have changed the air filter, cleaned the MAF sensor, changed both O2 sensors, changed the secondary air valve and relay. I've done the carb cleaner spray test around the intake and vacuum lines, with no spikes in RPM.
Most recent try was a couple bottles of Techron concentrate with premium chevron gas.(still waiting to see if the code hits again)
Next steps are checking the intake bolts(to see if they are torqued) and intake gaskets, check for exhaust leaks at the exhaust manifold, and checking the MAP sensor.
Freeze frame data from the most recent hit on the code is below.
***Fuel system 1 - CL***Fuel system 2 - NA***Calc Load(%) - 30.2***ECT(deg c) - 48***STFT B1(%) - 3.9***LTFT B1(%) - 22.7***MAP(kPa) - 33***Eng RPM - 809***Veh speed(km/h) - 0***Spark Adv (deg) - 10.5***IAT(deg c) - 20***MAF (G/s) - 5.82***TPS(%) - 15.3***Air status - NA.
View 7 Replies
I have a 2001 Passat 1.8T that has the pesky MIL light on with a DTC code P0171 lean system. I have sent it to the mechanic many times to no avail. What the mechanic did was replacement of the MAF, O2 sensors, checked intake manifold leak as well as exhaust manifold leak. His last attempt was to check for clogged injectors and fuel filter and they were in good condition. He says the ECM is bad. I was able to retrieve freeze frame data as well as live data which shows that the computer is compensating what it thought was lean by having very positive LTFT of 22.6. I don't believe the ECM is bad but cannot be sure. There is one more thing that was not checked by the mechanic is the EGR valve. Could that be the cause of my woes - the lean system?
View 14 Replies
I have an 07 passat with a 2.0 4 cyl turbo and I have an error code of P0171 system too lean (bank1) but engine seems to run just fine, what this code means, am wondering if it is something I can fix or if it needs to go to the shop??
View 2 Replies
I have a P0171 code (lean bank 1 sensor 1) on my 2002 toyota camry 4 cylinder. I don't have any other codes except for an unrelated P1780 neutral safety switch code. It has had both codes for over a year.
I have replaced the fuel filter, the upstream o2 sensor, and the PCV valve. I also cleaned the MAF sensor. The mechanic performed a smoke test and found no vacuum leaks. Did a fuel pressure test and it's normal. Mechanic thought it would be fuel pressure because the car starts a bit slow when cold, but nope. The car runs great and still gets great gas mileage. I've never experienced a misfire in my 12 years of owning the car. I am asking because I am at a loss as to what it could be.
View 9 Replies
This is the infamous error code many Accent owners might have experienced it. The code refers to "Too lean intake system". People try to replace all kinds of parts like ECM, MAF, O2 Sensor, TPS, Fuel Pump, Fuel Filter, etc. according to my research. I just bought a 2001 Accent and the P2188 light came on. I wrote an email to Hyundai Corp. Asking what would be the most likely part that will cause the (P2188) check engine light to come on.
View 3 Replies
My 2007 Outback has had an off-idle stumble since I bought it a year ago. Otherwise runs well and uses less gas than the 2000 Forester it replaced. I've had a smoke test done, cleaned the throttle body, replaced front oxy sensor, and used a variety of gas treatments. I don't trust the local Subaru dealer to work on my car and my local garage has run out of ideas, but suggested MAF sensor may work. Some days it runs better than others. Occasionally I'll see a check engine light P0171 (lean) or P0420 (cat) but it will go weeks between setting those.
View 9 Replies
I picked up a really cheap Hyundai Elantra 2005 that the kid that owned it really beat up on. Right now I am trying to sort out the issues so that it can become my daily driver for the next few years.
Second issue, The check engine light is on and it is popping up a P0171 generic engine running too lean code. The car looses power sometimes and I can smell gas in the car. I have a friend that is going to be loaning me his MAC code reader so that I can see if it is one of the O2 sensors and if so which one tomorrow.
View 16 Replies
I have a 99 f150 with the 4.2l v6 with a 5 speed 173000 miles. I picked it up not to long ago. When I first got it it had both the P0171 & P0174 lean on bank 1&2 it was also siting for a while. I replaced the fuel filter which was filled with black fuel, also changed the PCV valve, cleaned the MAF sensor, and changed the oil. I cleared the code, drove it for a little bit and the light came back on after 20 miles.
I then proceeded to replace the upper and lower intake manifold gaskets. Upon doing that i noticed that i was missing one of the linkages for the IMRC. I went to the junkyard and pulled off another linkage rod off the same motor. ordered new plastic clips, put the IMRC on cleaned everything up and began putting it back together. I also cleaned the Injectors while i had them out as well and put in new spark plugs and wires.
Put everything back together. code was cleared since the battery was disconnected. drove it and then the engine light came back on again. this time it was only the p0174. so i then both the upstream and downstream O2 sensors on bank 2, reset the code and it came back on again. I'm lost.
View 2 Replies
I've been chasing this P0171 code for over a year now. STFT is normal plus minus 5 but LTFT won't go below 21.1%. At highway speeds the lowest the LTFT will go is 10-15% then goes back up to 21.1% at idle.
Things I've done:-
- New the air intake gasket to the Orange one
- Cleaned the MAF sensor
- New PCV
- Smoke test reveal nothing (vacuum is at 21-24 in-Hg) (did not smoke test the exhaust yet)
- Changed to used fuel pump. Funny thing here is that now when I shift the car to park the STFT steady increases to 25%. The old fuel pump never done this. But the car feels like it has more power now.
- New gas cap
- Cleaned TB
- Cleaned fuel injectors and flow tested
- New A/F sensor and downstream O2 sensor
All parts were either genuine Toyota parts or OEM Denso. My next course of action is to buy a new Denso fuel pump or replace the ignition coil pack.
View 12 Replies
i have a 2005 camry 4 cyl. and i have a couple of code: second o2 sensor, system too lean, misfire cyl. 1 2 3 and 4. when i run the car it is incredible how much gas it take.
I first replace the second o2 sensor and i cleaned the maf sensor, air filter, iac and trhotle body but the codes came again.
View 2 Replies
1988 F250 351 5.8
I've worked for months on this truck and I now have it in the shop. The truck shows a 41 code and has a lean miss at idle that get worse during acceleration and cruise. The injectors were refurbished 6 months ago and the ECM was replaced 3 months ago. All sensors are new and within specs. Fuel pressure is good and there are no vacuum leaks.
The mechanic has verified that the condition is not electrical related. The O2 sensor will react if carb cleaner is sprayed into the throttle but other wise shows constantly lean. He's now checking all pins at the computer for any off condition. He is suspicious of the refurbished injectors. I'm wondering if the computer somehow went out again. Which way to go or what/how next to test?
View 9 Replies
About two weeks ago, while driving on a hot, humid summer night, the check engine light in my 1998 Toyota Corolla came on. The following day, I took it into my mechanic, who plugged it in and came up with the code P0441 (Purge flow fault). He told me it was likely related to the fuel vapor canister, though I see this can also have to do with vacuum lines for the purge valve and canister or a bad purge valve itself. My gas cap was, and had been, tight, so it wasn't something as simple as that.
Reluctant to deal with this immediately, I went back to driving it, and lo and behold - the light went off after several days! Unfortunately, the light came BACK ON after several more. And most recently (a few days after coming on again), the light has now gone off!
Both times the light has gone off, the weather has been rather wet, but otherwise, there doesn't seem to be a clear pattern. What this on again off again pattern might say about the problem?
View 10 Replies
I have a 2003 Toyota Corolla, mileage app. 106,000. Check engine light first came on when driving to destination 40+ miles away (most of my driving is shorter, around-town trips). My mechanic said code is P0420 and so they reset it and said if it comes on again that I need a new cat converter. It did not come on until about 6 weeks later when I was on a longer trip again (had driven about 40-50 miles). Can you tell me if the P0420 code absolutely means that a new cat. conv. is needed or if it could possibly be a sensor or something else hopefully less costly than a new cc?
View 3 Replies
I am having a difficult time trying to fix my CEL issue, The vagcom scan says P0171 & P0174 Lean banks 1 and 2. I don't believe both O2's went out I have Checked and cleaned the MAF Sensor did a quick vacuum leak inspection and all seems good. I have a GIAC ST 1 and an AFE intake with noise pipe delete. I can reset it but it returns after a day or so.
View 1 Replies
I recently had some work done on my 2001 1.8t Passat. All new vacuum hoses & camshaft tensioner replaced by VW dealer. Check engine light is coming on and an independent shop near read out a code: Bank 1 mixture adaptation(multi): System too lean.
What does this mean??? And could this relate to these parts being replaced??? Work was done approx 2000 miles ago.
View 1 Replies
