I replaced my pads 3 months ago. Now I have a metal grinding sound (not squeaking). The mechanic says I need new rotors, and he will resurface the pads. I know I can replace the rotors myself; but do I need to resurface the 3 months old pads? If so; how will they resurface them?
View 4 RepliesI performed brake maintenance today with my brother on my 2010 corolla CE, my front rotors were warped and my pads were used ( and also uneven) and I replaced both front rotors and pads.
The install went smoothly, my brother changed a couple of brakes sets and knew what he was doing and showed me up.
Took it for a spin, the brakes work very nicely ( i bought the ceramic wagner bundle ) but theres a slight grinding noise when driving, like the pads are touching and rubbing a bit too much on the rotor, but the driving is unnafected. Also, there's a sqealing noise coming from either side when you turn only.
Braking itself produces no noise whatsoever, only when you turn that it squeals.
Thumping noise in rear passenger side. I removed pads and rotors, inspected and found nothing wrong. I decided to replace the new rotor with same and the thumping is still there, but only with the brakes being used. Nothing felt in the brake pedel and the the van stops fine. So why the thumping noise?
View 4 RepliesOk so we just replaced our front and rear brake pads and had the rotors turned. Our rear brakes are fine but both our front brakes now make a clunking/popping noise when we brake.
View 4 RepliesToday I decided to change my rotors and pads out.. Got everything back together and i believe car is in limp mode.. It wont shift out of 3rd.. Abs light on ,check engine light, traction control and stability control light on.. Also my speedometer doesn't work but my rpm"s do...hooked up scan tool and comes back as wheel speed sensors.. I never touched them or removed them....
View 3 RepliesI commute 180 miles a day, 6 days a week. I noticed metal on metal grinding noise(more noticeable) at high speed above 75mph especially on asphalt road. I'm sure noise is there at low speed but not enough to notice. My car has 50,000 miles. Tires? Electric motor?
View 7 RepliesI have an '02 Taurus. For the last year or so it has intermittently produced a metal on metal grinding noise while failing to start up. I'm told this is due to teeth being missing on the flywheel between the starter and the transmission. It's taken as many as six tries to get the car going. But the car has always started in the end.
My questions are: Is the problem flywheel worth replacing at this point at this price? Is it likely to fail totally any time soon?
Also, might the March '09 replacement starter be implicated?
I have intermittent metal on metal grinding noise. Seems to happen when I am at highway speed. Seems to go away when I put it on 4 wheel drive or slow way down. On one occasion though, the grinding noise did not stop even after putting on 4 wheel drive - had to stop completely before it went away (did not come back after I drove off again). Diagnostics so far....
Unhooked the vacuum lines on passenger side actuator and hooked up vacuum gauge. Vacuum held at 20 psi and drops and raises slightly as the truck is being revved. Takes about 10 seconds for vacuum to drop to zero once truck is stopped. Putting it on 4 wheel drive drops it to zero immediately. Exact same scenario on the passenger side.
This leads me to believe my IWE solenoid is ok. So also my check valves. Next opportunity I get, I will raise one wheel, remove the vacuum line on that wheel and apply vacuum with my pump. Want to see if it will turn my half shaft.
2004 F150 FX4 ....
I have a 2011 Prius with about 32K miles on it. I've been hearing light metal on metal grinding noise for a few days now. So I decided to take it to a stealership and they told me my ceramic pads and brake rotors both need to be replaced for all 4 wheels. I thought Prius brakes don't need to be replaced for 100K miles.
View 7 RepliesMy 2009 Toyota Corolla has started to make a grinding noise when starting. The sound is identical to when you try to start an idling car. What the problem is?
View 7 Replies I have 2009 corolla with 70000 miles on it. I replaced new brake pads. I have some metal grinding noise when i turn right only. I tried looking online and got few similar problem faced by other people. I am not sure if its exactly same issue. No accident damage. Mostly driven on freeway.
1) noise looks similar
2) I do not get noise when i accelerate
3) for car this old is it expected ?
When I start my car (usually a cold start) I hear a TERRIBLE grinding-like noise. Other times it sounds like a shuffling noise. And then other times it's like its over-exerting itself trying to start up. I've taken it to the dealer many times as it's a 2014 Corolla. They have no answers. The claim it's just a characteristic of the car. I call bull. This isn't normal for any car. My car has a CVT transmission by the way. Could it be the starter? Spark plugs? Note: the noise is about 1000x worse in winter. Audio is attached in separate comment.
View 19 RepliesI have a '98 5-Speed Corolla. If I rev the engine when the car is in neutral and warming up I hear an odd grinding noise when I let off the gas and the engine goes down to idle. The noise does not occur if I put my clutch in. Is this something to worry about?
Also, I'm wondering what CV joints sound like when they're failing.
I have an '04 Corolla with 206k with a slight grinding noise from the right front when I make a left turn. Is it the outer CV joint? The noise sounds like the tire is rubbing against a splash guard but it's not.
View 3 RepliesI recently brought my 2005 toyota corolla to my mechanic to give my car a check up as i will be going on a three week road trip soon.Upon assessment, my mechanic told me that my front right wheel bearing was making a strange noise and that i should replace it. I went ahead and had it replaced. after i had it replaced the front right wheel area was still making a grinding noise (louder than before it was replaced). I brought it back and he replaced it again with a new wheel bearing.
Again after the 2nd replacement it continued to make a load crunching, grinding noise when ever i brake the car. So once again, i brought it back. I thought perhaps it was my brake rotor and had him check that. He did just that and said the break was fine. He said it may be because the axl was not sitting true. so i had the axl replaced. well today i picked up the car and drove it approx 5 miles and the same crunching/grinding noise persists!!! I brought it back and it is once again being worked on. I need it fixed and am worried that my car won't hold up for my upcoming 4000mile road trip. I have attached a video clip of the sound to this post.
Our 05 Corolla, 160,000 miles, has started making a grinding sound when we upshift into 3rd, unless we let the rpms fall to below 1000. My husband said the clutch needed adjusting, but the dealer said this clutch is not adjustable. The dealer found nothing wrong and could not get the car to make the noise while in the shop. (It did actually get better for a while but got worse again almost immediately after the visit to the dealer.)
Our other car (a Saturn) has over 250K miles on the original clutch, so I don't think it's our driving. What could be wrong, and is this something that needs to be addressed soon lest we damage something irreparably? Also, this car has, since purchase, been nearly impossible to shift on the coldest mornings. Really, sometimes it is all I can do to get the lever in reverse to back out of the drive in winter (in Kansas). Warming up works, but it seems to take an inordinate amount of time before shifting is"normal."
I was driving my car today, and I stopped at a stop sign. When I went to go, I pushed the gas, and my car revved up, moved forward, then all of a sudden it made a loud grinding noise (Like I was dragging metal sheets), and the gas stopped responding (but the engine was still running). The car still turns on, but whenever the gas is pushed, it doesn't go and makes that awful noise. What could be wrong?
View 2 RepliesMy car has been doing this more. When I turn into a parking spot or my works' parking garage my car front end makes a Metal Grinding noise But it does not make this noise when I am driving - turning corners. Car is a 2007 Toyota Corolla LE (I miss my Beetle). The Toyota service says brakes are fine and they see nothing. I am not the only one that hears it... My son has hard it and I have startled some pedestrians.
View 1 RepliesI have a 2009 Toyota Corolla and it's making a loud grinding metallic noise on the front left side. It does it while I drive the faster I go the louder it gets. When I turn to the left it makes it louder, when I turn right the noise decreases. PG&E have been breaking the roads by where I live and there's a lot of little rocks I drive thru. I'm wondering if that's the problem?? What do I do?
View 4 RepliesI've had a 2006 Passat 4Motion for about 15 Months now and it just went in for it's 20k mile service. The dealer told me that the front pads and rotors were shot, and the rear pads needed to be replaced.
I've read that the front brakes are rather easy to change but my question is: are there any aftermarket pads and/or rotors that last longer than the OEM ones? I just don't think I want to do brakes every 20k miles. Now in regards to the rear brakes, apparently my rotors are okay but my pads need to be replaced. I've read that you need the VW "Vag Com" to do that and I'm new to VW software stuff.
On 8/18/04 VW told me that my 03' Passat (38'000 miles) needed new rotors & pads. I bought the car new. They told me that VW used rear pads that eroded quickly and provided new rotors on the house. I decided not to press my luck and paid for new pads. I look at my pads now through the rims and it seems dangerously thin and the edge of rotors has gouge all the way around. HAS ENOUGH TIME PASSED FOR A LEGIT REPLACEMENT ON THESE PARTS?
View 4 Replies