Toyota - Corolla :: 2000 Struggles Up Hills Or Speeding Up On Highway - Bad Cylinder
Apr 26, 2014
My 2000 Corolla has been a dog from the day I bought it, a few years ago. It struggles up hills or speeding up on the highway. I took it to a local garage and was told that one of the cylinders was fouling a spark plug with oil. The owner said the cylinder would need to be machined to correct the problem. The total cost of repairs would be about $1800. My question is, would I be better off purchasing a rehabbed cylinder and having him put it in? Is this even possible? BTW, the car only has 132k miles on it, which is not a lot for a Corolla.
View 16 Replies
Advertisement
95 corolla 277k miles. 4 hours into a long trip went over a huge bump and the shocks seemed to "bottom out". Like they compressed as much as they could. Pulled over half hour later for a break.
After that drove rest of way home. Car started shuddering and slowing down going up a hill. Had to floor it just to get it to be 60 mph. Hill wasn't that steep. Seemed to do ok on flat parts.
Was a little low on gas so pulled over to fill up. Noticed car idled very roughly felt like it was going to stall while pulling into gas station.
Gas cap was a little loose. Didn't hear the whoosh of the vacuum you usually hear when undoing the gas cap either.
After that it seemed to be a little better going up hills. I drove it home, and a day later drove it and it seemed to go up hills ok.
It still idles very weirdly, roughly and like it's about to stall. While driving it sounds ok.
I was thinking fuel pump but now i'm not sure. It might be related to the gas cap, maybe the bump loosened it.
View 9 Replies
So my wife's 2005 escape has been slowly losing power over the past 6 months or so. I regularly change the oil, tried new spark plugs, new air filter and still it's lazy. I know it's not a race machine but it struggles on hills.
This winter it was having problems starting unless the accelerator was pushed to the floor. After a cleaning of the Idle control valve all was well again. It has roughly 72,000 miles on it and uses .5-1qt of oil between changes.
View 2 Replies
I'm a new 2007 Prius owner, and I know that the Prius is no sports car, but this acceleration is very slow. When I'm speeding up to get on the highway, it really sounds like the gasoline engine is working hard to get up to that speed. I've had cars in the past where the emergency brake gets stuck, can that be a probable cause, or is this type of slow, strenuous acceleration normal for the little Prius?
View 11 Replies
I have a 2013 elantra with 42,200 kms. Recently I've been hearing a creaking nose while driving. Sounds like it is coming from the front driver side. Sound gets worse turning and speeding up on the highway on ramps. At highway speed the sound gets faster and almost sounds like a tapping noise.
At first I thought it was a strut but the strut feels stiff when pushing down on corner of car and I can't make the noise without driving. Sounds like maybe a ball joint to me?
I'm booking an appointment with the dealer tomorrow. I'm assuming that if problem is ball joint that it would be covered under warranty and not considered a wear and tear item as there's only 42k on the car.
View 1 Replies
Recently my car, after I put fuel into my car, my car won't start unless I apply the gas and then shift it into gear. I thought that perhaps replacing my spark plugs would fix this problem since it is about time for a tune up on my 2010 Hyundai Accent. About a week after changing the spark plugs I now have an error code that states that Cylinder 2 and 4 are misfiring and it is causing my car to shake while it is idling or speeding up. Also it is much slower than before to get it started from a stopped position.
View 11 Replies
I have a 2005 Toyota Corolla XRS with a manual transmission which has developed a shudder. When this shudder started, it only occurred when accelerating at highway speeds, or maintaining highway speeds. Now it happens at lower speeds if I give it gas without downshifting, but at reasonable RPM, 3000-5000. I cannot feel the shudder in the steering wheel, but the whole car shakes, and it definitely feels like it is coming from the front end. I have had the tires balanced and rotated. I also have replaced the IACV and MAF due to a CEL. These were replaced after the shudder started. For a few days after the replacement, the CEL returned, but now I am no longer getting it.
There are no visibly obvious issues with the suspension or the drive shafts or CV joints, and the motor mounts likewise look okay. I am not getting a CEL of any kind, and I replaced my plugs 6 months ago, but I pulled them anyway, and they are not fouled. I don’t think the issue is in my suspension, steering, or wheels because I cannot feel it in the steering wheel. I don’t think my half shafts are warped because the shudder happens at varying speeds, and the instant I let off of the gas, it stops. Though this doesn’t rule them out completely, there is no clicking from the CV joints. When I brake, the car slows smoothly, so the rotors are fine. I have run injector cleaner a couple of times, and octane boost once. These both seemed to solve the issue, but did not make it stop, and it has gotten worse lately. My wife did put low-octane gas in the car once, but it was weeks ago.
View 19 Replies
The car's engine just stopped while driving on highway, then would not turn over, nothing.Took for repair, said battery had bad cell or something, still under warranty, replaced.Fixed a few other things that were overdue, spark plugs, wires.
Okay. Next day, took the car on a few city driving short trips. While going across town on hot 85 degree day w/ ac on, it died again. Don't remember any lights coming on, didn't last time either. I think the AC died first then car died. Wouldn't make a peep. Right in middle of heavy traffic. When police came couldn't even steer. There might have been a slight weird noise which I thought was the ac making trouble right before it stopped, can't describe it really.
Had it hauled to shop again. It runs fine for them so far. They are still working on it.What in heck could it be? All belts were replaced a few years ago, car has always run well, never any major repairs just maintenance. It has about 133,000 miles on it. It has a clutch.
View 10 Replies
I have a 2000 f150 5.4 liter engine. I traveled about a month ago and while on the highway it started "bouncing/shuttering" really bad. I pulled off and while still in drive but completely stopped it was still bouncing but when in park it stopped. I took in into the Ford dealership and they said that cylinder 5 was misfiring and it was losing pressure fast. Then it stopped acting up completely and they couldn't find anything wrong with it.
Well about a week ago it started bouncing again on city roads (no highway). The check engine light came on and Orielys said it was a cylinder 5 misfire. Also, under the oil cap and in the tube where you would put the oil in has a yellow thick substance on it. I know that it is water in the oil. Also, there is a black "gunk" not far from where you would put the oil in. Could these problems be connected?
View 2 Replies
I have a 1999 Toyota Corolla. 4 cylinders.
I was on the road about 2 hours from home when my check engine light came on flashing. It stopped flashing so I kept driving. Three more hours of driving at highway speeds and it only came back on once. I then took it into autozone and the code reader told me I had a Cylinder 3 Misfire. The guy told me to change my spark plugs and I would be fine. It was time for a spark plug change anyhow so I drove home and did it. After I changed the spark plugs the car did not start at all. It would cough and sputter and try to start but not actually start. Changed the spark plug wires and then the car stopped even coughing and sputtering. It just didn't start.
I then noticed that my fuel line that feeds directly into the engine was rotten right next to the engine and if I pushed it in I could get the car to try to start. (Try and fail, but at least try.) The fuel line is a molded piece of rubber that flares at each end. It was one of the flares that was rotten and didn't seem to be sealing anymore. The hose is 7 mm inner diameter in the middle and about half an inch on the ends. I took some 3/8 in fuel line and used it to cover over one of the flares. The car tries to start now but wont. 3 of the four cylinders crank. I don't understand how I could break my car on such a simple repair job.
View 4 Replies
I have a 2000 Toyota Camry CE (2.2L/V4) w/ 130,000 miles on it. Just recently I have been experiencing a stalling issue after driving on the highway for 19 miles (or 20 minutes) at a speed greater than 65 mph. As soon as I exit and take my foot off the gas the car will stall as if I just turned the key in the off position. After I pull over, turn the key in the off position and wait a minute or two, the car start right up as if nothing happening. The idle seems to be ?normal?. The engine light does not come on when this happens.
If I feel the car may stall when still on the highway after slowing down, I can shift the car into neutral and hold the idle speed high enough to continue driving. However the car will eventually stall. But again and I restart it and be on my merry way without incident. I have try switching to high octane gas, but that did not work. If I disconnect the battery for a few hours the computer reboots itself and it will take a few more trips at high speeds for this issue to occur again. I have put in a fuel injector cleaner and cleaned the butterfly value (air intake). I own an Auto Xray code scanner; however it is not showing any error codes. What this issue may be?
View 1 Replies
My 2002 Accent sometimes struggles to start. It is generally a great reliable car and has a great service history. About 8 months ago I notice that two or three times it wouldnt start on first or second turn of the key. I got a service and the problem disappeared until recently again. Every so often (once a week or so) it will struggle to start and I will have to wait a few seconds before trying again, where it does fire up.
This is not a battery problem as I put a new battery in it 2 days ago. The fuel pump noise when turning the key also comes on. Could this simply be that the Spark Plugs ned changing? It has driven 5,000 miles since it's last service.
By the way, when I say struggles to start, it will turn over absolutely normally, but it will not ignite and actually start the engine, or "fire" up.
View 6 Replies
2000 toyota corolla feels like it has no brakesI had the brake master cylinder replaced a few months ago - so that's not itThe mechanic also replaced the shoes - so that's not itAfter I told him it still feels like the is low etc. he adjusted them or something - so that's not itIt still feels the sameWhat should I do?
View 7 Replies
I have a 2000 Corolla with 51k miles that I bought a couple of months ago.
Things I replaced:- both front ball joints- both front CV axles (half shaft)...previous left front one was leaking- all struts (complete struts that included coil, strut, mount)- all sway bar end links- 4 new tires (only put 200 miles on them)- balance and alignment - Firestone checked for bent rims - none found- Made sure all 4 PSI levels are 30
Before the new tires, there was a vibration at 60-70mph, after the new tires, there is a vibration at 40-50..seems to go away at 60-70mph. When braking, the steering wheel shimmied (turn left/right short distances rapidly)...replacing the ball joints fixed that....the mechanic also tightened the front control arms..that could've fixed it too.
When going very slowly over a flat road, I can feel the front left tire "hop" very slightly. By hop, I mean that it is not round like (seems like a high spot). I jacked all 4 wheels and checked for any amount of play - none.
Could this be an out of balance (even though I put 4 new tires) or control arm issue? Maybe the control arm bushings are gone and it allows vertical movement during load?
When turning the steering wheel left, it also makes a "pop" sound which is definitely coming from the strut mount area...might be related.
View 7 Replies
My 2000 Corolla CE does not have ABS, I've heard the correct way to brake is to pump the brakes. Should I press the brake slowly and then depress fully and then press again OR should I press the brake, depress half way, and press again? How fast should I pulsate it? My commute involves a lot of braking and I don't want the rotors to become warped.
View 10 Replies
I have a 2000 Toyota corolla with about 170,000 miles and it is using about one quart of oil every 500 miles. The last couple places I took it to said the compression was bad in the number 4 cylinder. Another place said it was a leaking head gasket. Which is most likely, and is it worth getting it repaired given its age and mileage?
View 13 Replies
I have a 2000 toyota corolla, with 1.8 16 valve. 105,000 miles, manual trans.. Just bought this veh. says misfire cylinder 4. So here is what I have done.
I started trouble shooting. swapping coils from cylinder 4 to other cylinders to see if the code follows after clearing it. No, stayed at 4..
So I moved on to the fuel injector. I did the same thing to see if it followed.. no stayed at cylinder 4. I changed the plugs, stilll misfire..
I did a compression check, I have 170 on 1,2,3, and on cylinder 4 I have 0. Yep, none...
I have some black smoke when the car is under load, as in acceleration, shaking and constant miss. lack of power... Trying to determine whether it is the rings or valves or what.. I took valve cover off and checked for broken spring, and they all seem ok. No oil in my coolant or vise versa.
View 2 Replies
I drove my car to the store today without any problems. When I started it back up again, I noticed a clicking sound. At first I thought that maybe I had turned on the turn signal or the emergency blinkers, but neither was on. I turned off the car and restarted it. The clicking restarted when I turned the car back on. I tried turning off my headlights, and the clicking got louder. I turned them back on and it got quieter.
At that point I decided to just drive home. The clicking stopped and restarted several times during my trip. I checked the oil, and it's fine. What could be making the noise?
View 3 Replies
Car is a 2000 Corolla with 62k miles. My rear brake light (driver side) went out (pretty sure it is the bulb). 2 months ago the blinker relay went out and I replaced it.
Do most mechanics have the bulb on hand?
View 5 Replies
I own a 2000 Toyota Carolla, in reasonably good shape (95,000 miles) with no rust on the body (it was a Texas car until last year). This problem happened in Texas, on the unusual times that it froze, and in Michigan, obviously very often. The car freezes: the doors edges, locks, latches, wipers, wiper fluid, windows, and trunk freeze solid. I've tried using the lock de-icers, hand sanitizer, WD-40, hairdryers, special fluid for the wipers etc. all to no avail. I live in an apartment complex so I do not have a heated garage at my disposal. This is a very annoying problem, which often means I cannot use my car, even though the rest of it works perfectly. I've searched the Internet for more answers, but find none. Clearly, there is moisture inside the car that freezes up in cold weather... but I can't imagine how or why. I've never spilled anything in there, and it's had a long, hot summer of drying out if there had been something there. But on the first freeze of the year, viola: no frigging way can I get into my beloved little auto.
View 11 Replies
I inherited my Mother's 2000 Corolla CE with low mileage. I know that since the car was knew, she had the dealer check on why the horn did not blow every time she pressed it. I do not have those repair papers, so I do not know what they did to the car. Again, after each of 3 visits to the dealer, the horn would work for a few months. Finally, she gave up. Arizona does not test the horn, anyway. So, now, I am having the problem. (Also in my V90 Volvo post). Two cars with no horns.. Short of pulling out the air bag and the wires? Bad ground somewhere?
View 3 Replies
