Toyota - Corolla :: 1994 - Key Won't Go Into Ignition
Feb 21, 2012
My 1994 Toyota Corolla wagon has a problem. I drove to work, all seemed fine. I jumped in it in the afternoon, and my key won't go in the ignition - it gets half way in, and that's it. It feels like the key is bumping into something into the ignition lock cylinder. In the interest of full disclosure, I've sprayed some WD-40 into the lock cylinder, thinking maybe the pins were jammed. If that is the case, it hasn't worked. Zero improvement. This originally happened when it was really cold out, so I've waited and tried it again on a warm (40 degree) day - no change (though my door lock and ignition have been more stubborn in the cold in the past, but only marginally so). So, what are my options? I guess you can't (easily) replace the lock cylinder without the key in the "on" or "acc" position (which I obviously cannot do). I'm not opposed to using a screwdriver as the key, or hot-wiring the car, but don't want to take drastic (or stupid) steps before being sure I don't have other choices..
View 6 Replies
Advertisement
I have a 1994 4 cyl Toyota Camry LE. For the last couple of years, when I parked the car after driving it and removed the key from the ignition, the air conditioning would continue to operate normally and blow cold air through the vents, and all of the other electrics would all operate for about 5 seconds, then shut down normally. Again, this was after driving the car, engine off, with the key removed and the ignition switch in the proper "off" position. I didn't think much of it at the time.
Recently, the problem has advanced to something worse. Now, when I turn off and remove the key, all electrical components remain on indefinitely (ie radio, air conditioning, wipers work, etc... )
I can physically power down each of the individual components using it's respective switch, but there is still accessory power on the vehicle. Basically, with the key removed, the vehicle thinks it is in accessory mode. All the dash lights are illuminated, like right before you start the vehicle. The only way to completely remove all electrical from the vehicle is to physically disconnect the battery.
View 6 Replies
I have a 1994 Toyota Corolla, automatic transmission. I went to start it this afternoon and it made a clicking sound a few times then went completely dead. When I jumped it, the dashboard panels, radio, lights, doors, etc. began to work, but it still would not start. I have replaced the alternator about 1.5 yrs ago and had the battery checked then too (it was fine then). I have had this problem before about a year ago, but it did start when jumped. I didn't leave my lights on or any doors open, so I don't think I drained the battery.
View 2 Replies
After a new distributor, check engine light coming on, getting a code 52, they (Toyota Dealership) replaced knock sensor. Unfortunately it seems to improve a little bit, but same issues happen; engine not running smooth at times. 94 Corolla. In the 223,000 mile club. 1.6
View 7 Replies
Periodically my 1994 Toyota Corolla 5-speed manual will not start. Other times it seems to hesitate before starting. The rest of the time it starts fine.
When it does not start: I turn the key, and hear the fuel pump relay click, and hear the fuel pump on the gas tank energize, but the car does not try to crank. I do not know if the starter solenoid is engaging at this time, as I could not listen for it while in the car. When I did try to listen for it while under the hood with someone else starting the car, it actually started (did not exhibit the issue)
When it hesitates before starting: However, sometimes, when I turn the key I hear the fuel pump relay click and the fuel pump energize, after about 1-1/2 seconds of holding the key, it does start.
When it does start it sounds normal, not like a low battery. The battery is new. I had the charging system checked at Advance Auto and they said the battery was good as was the alternator and starter. Plenty of cranking amps.
I disconnected the main wire on the starter motor and cleaned it with a wire brush. I also cleaned up the battery terminals.
I did find that the switch on the clutch pedal that allows the car to start when pressed has some fluid leaking on it (clutch fluid I think). Could that be causing the intermittent starting issue? If so, can I just clean it with WD-40 or something like that?
View 1 Replies
This car was running fine until my daughter brought it to a reputable tire shop to have new tires put on and an alignment done. The day after this was done, she started having issues with the car not wanting to move when it is in drive. It would eventually take off, but very reluctantly, and once she got going down the road it would be fine. After a couple days like this, it just wouldn't go at all in drive unless someone was pushing it. It goes fine in reverse.
The transmission fluid level had been recently checked, and was fine. Now when this problem cropped up and it was checked, the fluid was gone! We don't notice anything on the ground where it has been parked.
View 4 Replies
I have recently been having a problem with my Toyota Corolla. It starts up fine in the morning, but after a couple of hours of driving with the A/C on and the running lights (which are always on), and the radio, when I shut the car off, it will not start without a jump. With my heavy duty cables it starts instantly with the jump but then I am afraid to turn it off again. It has a genuine Toyota battery that has the dots removed saying it was installed Dec. 2012 although it looks older. After driving for a couple of hours the battery should be fully charged right? Or, does having the A/C and lights on suck up to much juice?
View 1 Replies
My 94 Toyota Corolla has about 190,000 miles on it and lately it has had a hard time shifting between 20-30mph. It finally does reach it and does not have trouble shifting at any other speeds. This only happens in the heat of the afternoon (Never have this problem in the morning). Also, my O/D light has been flashing when this happens, or at least around the time it happens. Could these two problems be linked? I took it to my mechanic in the morning and he checked the transmission fluid and it seemed fine, he also had no problems driving around when he tested the car. He said my transmission is going and that I should make "long term" plans. Is there any hope?
View 1 Replies
I have a 220k 1994 Corolla with I have come across a couple problems recently. It all started about a week ago when I decided to change my rear brake shoes. The old ones turned out to be all cracked and everything but were generally in pretty good shape in terms of wear. Anyways I put the new shoes in (my first brake job) and tightened up the e brake cable and went for a test drive. I walked away extremely satisfied, the e brake worked perfect which was my main reason for changing the shoes in the first place.
Basically the whole thing worked perfectly until 2 days later. I was driving for about 8 miles when my brake pedal suddenly fell through to the floor (or pretty close) at first I even thought I hit the clutch pedal! anyways after pumping the pedal a few times my pedal feel returned about 70% and after another maybe 10 seconds braking power was lost again until I pumped the pedal. So lucky for me my destination was a 1/4 mile away so I parked and checked the fluid level; it was at the max mark, then I check the wheels/drums and they were REALLY hot.
Also the driver's side drum had a faint smell of brake fluid. Anyways about an hour later I went for a short drive and the brakes worked fine so an hour after that I drove the 8 miles home and about 1/8 of a mile from home same thing happened; brake pedal basically goes almost down to the floor until pumped. My thoughts were that the new shoes were constantly rubbing and the old fluid overheated and caused failure so I flushed the system and put new fluid in and adjusted the shoes "in" with the click adjuster bolt. I had a really hard time getting the drums of to begin with. That and I loosened the e brake cable just in case.
So the next morning I drive about 5 miles without using the brakes pulled over to check that the drums were not heating up anymore (they weren't) so I thought I had fixed it. Well 3 days later (last night) I was experiencing the rear brake stickiness again. Basically when I was just moving from a stop where I had used the e brake to secure the car, I could literally feel that the rear brakes were stopping the car pretty aggressively and sure enough after a few more miles my brake pedal fell through so I poured water on the drums and they started to let off lots of steam, even after like 10 bottles!
So I limped to my friends house at 12:00 AM and jacked my car for a look. Again the drums really didn't want to come off and once we did get them off my friends dad inspected them and could find anything wrong with my installation. The conclusion that we came to was that the auto adjustor for the shoes makes the shoes too tight and they rub. So I am thinking maybe this is cause for the fluid to overheat and boil, causing the pedal to fall through. The pedal fell has gotten much worse since I bled the system 3 days ago so that may be an indicator. Did a test this morning for 5 miles and the drums were just below lukewarm.
View 1 Replies
My 1994 Toyota Corolla's speedometer just stopped working while I was driving this morning. Does this mean that there could be something worse going on than just my speedometer?
View 4 Replies
My 1994 Toyota Corolla idles at around 1500 and 2000 RPM just about anytime I drive it.
It is worst when I first start the car, and it gets better the longer I drive, however, it is still well above a normal idling range!!
I add oil regularly and do check the levels on most of my fluids on a weekly basis!
View 4 Replies
have an 2009 Toyota Corolla 62K miles. If the car sits out 8 hours or more in VERY COLD (zero degrees) weather makes a 1-2 second clashing/sparking noise the split second after turning the ignition on but before engine starts. I tried to attach video/audio. The car starts and runs fine. isn't a ticking or knocking or tapping noise assoc. with bad engine. It isn't squealing noise assoc. w/ serpentine belt. I've been waiting for it to get cold enough to leave overnight at Toyota dealer. I keep wondering if it isn't related to the botched oil changed at the Toyota dealer a couple yrs ago when they forgot the oil & I ran car about 30-60 seconds. At the time, they said all was okay and did compression test (Cyl 1=178psi, #2=175 #3=180 #4=178) all within the normal specs 145-189. I got a 2nd opinion at another Toyota dealer at time who removed valve cover and inspected cam caps and scoped cylinder walls and said all was okay and compression good. No mechanical problems- uses no oil, check engine light not on, etc. What noise is and why just when very cold and car sits out long time?
View 18 Replies
I have had this car for sum yrs never had any problem a couple months back while driving it would just shut off. Well come to find out my ign fuse would be blowing. I would replace it and it would start up and run just fine. Since then my daughter owns the car and it happened again and she replaced the fuse and it started up fine but while out of town it just shut off and now even if you replace the fuse it just blows. Just as you turn the key, it blows. So i did sum research and replaced the ignition switch. Tryed to start it and it still blows so im at my wits end. If I knew what every component that fuse ran , i could figure it out by process of elimination. I have the Chilton book but i still can't seem to find what all components that one ign fuse runs. It is a 94 grand am 3.1 v6....
View 7 Replies
I have a 94 ranger with the 2.3l engine there is no spark at the ignition module (the front one both on the drivers side) that controls the plugs on the drivers side of the engine. I swapped with the module for the exhaust side but the problem stays at the same two plus and doesn't move with the module .. What can be the source of this problem? ECU?
View 6 Replies
I have a 1994 F150 XLT 5.0 . The problem i am having is when I turn the ignition on I hear the fuel pump come on [both front and rear tanks] and it should stop when the system is pressurized but it does not,and the truck then fails to start. Intermittantly the pump does stop and the truck starts up.
There is fuel at the rail and there is spark,i have changed the filter ,fuel pressure regulater and the pump relay to no avail.
View 4 Replies
I easily removed the key lock cylinder but when I went to put the new one in I cannot get it to turn all the way back to lock the pin in place. The steering wheel is not in the locked position nor can I get it to lock. I have turned the steering wheel as far left and right as I could go with no success on getting it to lock or on getting the ignition key lock cylinder to turn back securing the actuator pin. The old key lock cylinder won't go back in either. What am I doing wrong?
View 3 Replies
Just had a problem with my 96 corolla (200 000 kms) and I thought I would post how I repaired the above - hopefully could be useful to someone else.
Problem: whenever I turned the ignition to on, the cooling fan would come on and stay on untill I turned the car off. The car was behaving this way regardless of whether it was cold start or hot start.
In my case, the problem was the cooling fan switch (or some say sensor). It should test for continuity when engine cold. When the engine is hot, it should have no continuity. In my case, I had no continuity with the engine cold... so therefore the sensor 'tricked' the fan relay into thinking that the engine was too hot, hence the fan was always on.
Note that on this Corolla, there are two sensors (at least) for the cooling temperature. There's the cooling fan switch sensor and there's the sensor the sends the temperature to your temp gauge. That had me scratch my head a bit.... cause at first, I connected the car to an OBD2 and could see it was reading the temperature ok.... so I had initially ruled out the sensor... but a bit more research and I realized the fan has its own sensor.
How to fix it: The sensor is right underneath the distributor. Here's what I did:
1) empty about 2 litres of rad coolant into a clean container (you don't want coolant to leak when you take the sensor out.)
2) Unplug the sensor.
3) Pull the coolant overflow container out of the way. it's a slide in... just pull it up and out of the way.
4) Use a 17mm deep socket, remove the old sensor, pop the new one right in.
5) Reconnect sensor, put overflow container back on. Pour coolant liquid back in. make sure rad cap is on.
6) You're set. 30 minutes max.
Here's a picture of what the cooling fan switch looks like....
View 6 Replies
I have a 2009 corolla ce i can get the key in to the ignition ...
View 1 Replies
I was installing the footwell lights and now the headlights on buzzer does not work. And when I press the lock/unlock button on the key fob, the corolla actually locks and unlocks the car WHILE the doors are open! Also, the key in ignition buzzer doesn't work as well!
The seatbelt buzzer works though. I don't know what to do and I want those Features back!
What happened is that I was trying to zip tie the led strip on the metal bar under the steering wheel behind the panel with the tire reset switch. I guess the + & - terminals touched the metal thing and there was a little spark! The dome Lights work and so do the foot wells! But the buZZER doesn't!
View 4 Replies
I just recently picked myself up a 13' Corolla CE! Love it but have found some quirks that Im just wondering if this is normal with other 13' owners. Car has roughly 3000km on it so far.
-When I start the car, it almost sounds like my speakers 'pop' once I let off turning my ignition. Its not a extremely loud pop, but loud enough to make one think, "what the heck was that?" Have others had that issue
-Recently, its been a bit colder here (-3 Celsius). I have noticed it takes roughly 5 minutes of continued driving for the engine to warm up to normal operating temperature. Is that normal? Should it warm quicker than that? Its almost like the thermo is stuck slightly open.
View 4 Replies
Is there any way to change the sound the car makes when you have your key in the ignition? I have various audio samples and once of them is a females voice saying "command codes verified". I want to have this sound bite 'chime' when I put the key in the ignition.
View 7 Replies
