Toyota - Camry :: Replacing Lower Control Arms?
Mar 21, 2013
I have been told by a couple of mechanics that the bushings on the lower control arms on my 95 Camry are worn. They recommend replacement of the lower control arms and ball joints.Is this a repair I can do myself? I have reasonable mechanical competency. I figure that I will have to rent a tool at the auto parts store for the ball joint, remove a few nuts and bolts, and bring the car in for an alignment once I get the parts installed.Now my wife is adamantly against me doing this myself. She thinks that I am going to mess this up, the parts will fail at high speeds, and I will die in a fiery crash. She apparently has more confidence in the repair shop grease monkey than her engineer husband. So is she right? Is this a repair which is best left to the shop?
View 7 Replies
Advertisement
I am going to start on the control arms on my 04 V6 Solara this afternoon since the bushings are beyond gone.I have done control arms on my 98 corolla but i didnt have to deal with the stupid motor mounts being in the way.I have done a search and it seems(if i have this right)that i need to
1.Remove Dog Bone
2.Loosen right and left side motor mounts but dont remove the bolts.
3.Jack up the engine just enough to get a wrench on the hidden bolts on each side.
Am i missing anything?I already have the Mevotech control arms with new ball joints already attached.I plan on renting a ball joint removal tool from autozone.
View 2 Replies
Had after market front struts installed by a non-dealer shop on 2006 Toyota Sienna. Dealer service dept diagnosed two months later that the struts were one inch too long and caused damage to the lower control arms. A director for training for the other shop (one of 80 + shops) completely discredits the dealer shop's theory about the relationship between the size of the struts and the damage to the control arms, while admitting the error with the struts. Both sounded credible as I have very limited mechanical background.
View 19 Replies
Replacing lower control arms? I've read a couple places that you don't need a spring compressor. Anything else to look out for? 2000 F150 4.6L 2WD 288,000 miles....
View 3 Replies
My daughter has a 1999 Passat 4cyl.... In the last year I've had 2 lower control arms at the front ball joints just break away. Lucky it has been when she was either stopping or at very slow speed.
On inspection this looks like a very unsafe design flaw. The aluminum control arm is strong except for the light metal around the ball joint it's self. If one of these let go at speed it could be fatal!!
What causes the break other than normal wear and is there any signs before one lets go?
View 3 Replies
I changed the Passenger side with no problem , the driver side bolt is hitting the transmission oil pan. I am thinking of loosening the mounts and try to jack the pan up to get that 1 clearance or worst case drain the transmission take the pan off remove the bolt and put in fluid in. If I drop the the transmission pan is there a filter in there? also how much transmission fluid does it hold.
[IMG] ....
View 2 Replies
I have an 03 Camry LE I4 with about just under 100k miles. Recently, under semi hard braking at highway speeds, the steering wheel will shake quite a bit to the point that I don't feel safe braking hard. I initially thought the brake rotors were warped, but those were replaced less than 2 years ago somewhere around 80k miles. I've taken it to many shops and here are the verdicts they've given me:
1. Rear drums are warped which is the problem (I don't think so...)
2. Control arm bushings need replacement (coming from shop who did brake work before)
3. Ball joints need to be replaced
4. All rotors should be resurfaced
What should I do?
View 9 Replies
I have Bluewater adjustable control arms, they have been on the car for about 22 months, and for the last few weeks they have been squeaking and creaking like a bastard, over any imperfection in the road.
We had the car up on the lift, and twisted the control arms, and it's definitely coming from there. I'm not the best mechanic in the world, pretty far from it, so is there a way to remedy this without replacing them? It sounds like I'm fornicating in a 1986 Caprice every time I hit a bump.
View 18 Replies
Dealer told me needed new control arms as the bearings are wearing out. Was quoted a little over $3k. Doesn't really bother me bc it only makes a clicking noise when I apply brakes hard but concerned about safety issue. Surprised a car like this would need new control arms with only 70k miles on it.
View 14 Replies
I need to replace both the struts and the control arm but I don't have a socket to fit, what is the correct size socket I need ....
View 9 Replies
Last week the coil went out. The housing had several cracks, and the heavy oil had filled the distributor cap. So the coil, rotor, and distributor cap were replaced. About 4 days later, all my engine would do was make a grating sound when I turned the key. My boyfriend said that it sounded like my starter had gone. It wouldn't start with hitting it or anything. So, he and I, while trying to save some money because we're both on disability, replaced the starter. Now, when I turn the key, nothing happens! We're pretty sure the battery is dead. We have it on a trickle charge right now. But a funny thing happened, all of a sudden the open door alarm started going off! The door had been open for several minutes when it started. So we think that it may be a short. The starter relay, when you look at it, has a spot of corrosion on the indicator. Tomorrow we're going to try cleaning them.
1993 Toyota Camry DX with 170,000 miles ....
View 4 Replies
I'm halfway through replacing the ball joints on my '03 F-150 4WD. When I pressed the new lower ball joint in, it's snap ring groove is ~1/8" above the top of the lower control arm surface. These are Moog 8695T joints. I've taken them in and compared with another new joint at the parts store and they seem to be correct. This implies that the control arms are not correct- they're too thin where the joint presses in. The old joints sat the way they should, with the snap ring flat against the arm. The old joints are definitely different than the 8695T's- they are shorter from the shoulder of the joint to the snap ring groove. I'm guessing that now I'll have to replace the lower control arms, as well.
View 11 Replies
I have a camry 2000 automatic transmission with 150 K on it. For last few months I am having this sporadic issue with it having difficulty to change the gear from lower to higher gear(from the first to second, i guess). It goes like this, when i start speeding up the car, its having difficulty to move to higher gear, it just revs up to like 5 - 6 K rpm and with a jerk it shifts the gear. And at the same time check engine light goes on. And during the time this check engine light is on, it does this same thing a couple of times or so.
Then after some time the check engine light goes away and the car runs just fine without any issues for some tine and then the same thing happens again and after some time the issue and the check engine light goes away and the car runs just fine again. this keeps happening every few weeks. So I took the car to the mechanic (check engine light has gone away at this time, who told the code was showing some "speed sensor" issue and they replaced this. After that the car ran just fine for a couple of months. But its starting to do the same thing again.
View 4 Replies
This past Sunday, I replaced the spark plugs on my 2008 Toyota Camry CE, following one of the sticky DIYs. My car has approximately 107,xxx miles.
Last night on my drive home from work my CEL came on. First time seeing a CEL light since my BMW days, . Luckily, I have a OBDII scanner at home and after running the scanner, it gave me the following trouble codes:
- P0101
- P0172
I went ahead cleaned the air filter (I have an Injen SRI installed).
After doing some research on the interwebs, I have concluded that this code has to do with the MAF. Time permitting, I am going to clean the MAF sensor later tonight. In the meantime I reset the CEL, to see if it will come on again.
My only question, which I am unable to find an answer to, is:
Can there be a possibility that the P0101 and P0172 trouble codes be related to me replacing the spark plugs, or is this just a mere coincidence?
View 5 Replies
Own a 2000 Camry XLE 6-cyl. Both valve cover gaskets are leaking. Rear one leaks onto the manifold and causes stench. Have been quoted $350. to replace because the job is complicated. Have any of you done this on your own, and if so, would you recommend it or go to a qualified mechanic?
View 9 Replies
So my strut mounts are shot and I wanted to add adjustable rear control arms to eliminate tire wear. So thinking of going with Bilstein HD's with the stock springs. Oh and BTW want to keep stock ride height since it is my daily. The only option I would consider for springs would be the euro version of the stock springs.
View 4 Replies
Ive had my Camry since around September of last year. It had between 100-110k miles at the time of purchase.
In the last 3 months, Ive started to notice that sometimes when I am on the road & switch on the cruise control, the setting appears to have trouble engaging. On some occasions the cruise control does not even switch on at all when I hit the "set" button, while at other times I can feel the setting turn on and off intermittently, while I feel the engine respond accordingly with more or less gas with each time it goes on and off.I can also see the cruise control light on my dashboard begin to flash on and off each time this happens.
This does not happen every time I drive, but I must say Ive never seen anything like this before in any other car Ive ever had, and I find whats happening here to be both very strange as well as very annoying.
View 4 Replies
Some fool with a tow hook must have backed into my rear bumper this morning because the black plastic spoiler is pushed in pretty bad on the left corner (to the left of the exhaust). Before I have it replaced, I want to have a go at banging it back in place, but the dent is at the crease and I can't do it in situ. Is there a DIY about removing the spoiler (the lower black plastic half of the cover)? Or if not, one for dropping the whole bumper? There seem to be a bunch on the GTi and Passat but none for Tiggy.
View 4 Replies
I recently bought a 2007 toyota Camry le v6 with less than 38,000 miles it currently has 39,300 miles and my check engine light is on along with the VSC and a skid control light (car with squiggle lines behind it) we have a had lots of rain here where I live and I had to drive through a couple deep water puddles. I looked up online and it said The engine light may turn on if the VSC and skid control lights are on. Could this be that the sensors maybe got wet? I don't think anything should be wrong with this car considering it's a toyota with less than 40k miles
View 14 Replies
The check engine light on my 99 Camry went on at about 180,000 miles. My mechanic checked the code and turned up an EVAPORATIVE EMISSION CONTROL SYSTEM INCORRECT PURGE FLOW He said this could be any number of things,including the need for a gas cannister or some type of valve. What does this mean? How do you determine exactly what the cause of the problem is? What are the likely fixes? Will Toyota be able to better determine the cause than my personal mechanic? What are the best options?
View 5 Replies
Had I to break into my gas cap, replacing the module? is it ok to buy a used one? My door locks quit working too. the same module right?
View 1 Replies
