Toyota - Camry :: Brake Pedal Is Softer Than Before So Have To Push Harder To Get Car Stopped
Jan 21, 2015
I have a Camry at 120K now. Front brake pads was placed at 85K and was told by the maintenance person at that time that brake rotors couldn't be resurfaced since they were close to the minimum thickness.
Braking seems still fine these days. I don't hear any high-pitched noise or feel obvious vibration/pulsation when the brake is applied. The brake pads are still within a good range of thickness as the last check was made a couple of months ago.
But the brake pedal is softer than before so that now I have push harder to get car stopped. It that a warning sign which indicates it is time to replace the brakes rotors and pads?
View 1 Replies
Advertisement
I normally drive my 2010 Prius. But I have been driving my wife's 2012 Camry XLE the last couple of days. (My Prius was clean and hers was not.
Well twice in the last two days I started her car and put it in drive to find it was accelerating uncontrollably! The harder I pushed on the brake the harder it accelerated.
After taking my foot off of the brake I discovered that my size 13 EEE shoe was on both the brake AND the accelerator.
Now knowing this, the same thing happened the second day! Luckily They both happened in parking lots and NO damage was incurred!
This has never happened in my 10 Prius or my 08 Prius. maybe the pedals are not as close or the Prius's low end power was not noticeable.
It would be ironic if all the BS over the floor mats came down to big feet or improperly placed pedals. My feet have been the same size for 50 years and many cars and NEVER had this occur before.
View 14 Replies
Recently the brake pedal on my 2002 Prius has been a little harder to push for the first mm of travel it almost "sticks" requiring slightly more effort once it moves past that point it is normal no fading or extra effort required this problem has now progressed to the point where the pedal is kind of crunchy for the first 5mm of travel and occasionally will not return right away causing the brakes to drag a little but again pressure required to stop is exactly the same no fading etc
I am thinking since I live on 2 miles of dusty washboard dirt road and some grit has worked its way into the bushing .
View 19 Replies
2000 Chevrolet Silverado 1500... When slowing down for stop, when almost stopped, sometimes the brake pedal pushes back momentarily, makes a bit of a (errrr) noise, and for two or three seconds during the push back the brakes do not work. Mechanic has cleaned ABS wheel sensors. All brake pads are good. The truck computer shows all systems okay. All brake lines are new or one year old.
View 2 Replies
I just changed all my flex lines to stainless steel and my pads and rotors were replaced. I had some issues with calipers dragging. I used a power bleeder to bleed the brakes all the way around. Now my pedal feels really weird. If I push the pedal fast it brakes hard then it goes to the floor. If i just push it soft, it will just slowly go to the floor without braking at all.
View 3 Replies
Three days ago while stopped at a light the car creeped forward forcing me to press harder on the brake to keep vehicle from moving.
Next day drove for 100+ miles with some stop and go traffic no problems. Third day drove 50 miles and upon arriving at home brakes felt spongy and nearly hit the floor the dash illuminated "Check Brake System".
My Camry has 5437 miles on it.
The dealer just called and said they need to replace a "brake booster". They said there is a TSB that addresses this issue in a VIN range.
Image here : YouTube [URL].....
I'm glad I was only stopping to pull into my drive way and not the freaking stop and go freeway traffic on the way to work in the morning.
View 3 Replies
80km on my accent, the brake pedal was getting softer and brake fluid was a bit low as normal due to brake pads were worn up over time. Brake pads were never changed. I thought changing the pads would change the softness of the brake pedal. I changed the brake pads, left and right, the brake fluid in the reservoir went up as normal but I drove around but the softness of the brake pedal did not change. I still had a little less than half size on the old pads. I need to press the pedal a bit much to feel the brakes. I am wondering maybe the brake pedal was always like that when I bought the car.
View 4 Replies
I have a 2010 toyota camry that needs a parking brake adjustment. the car still stops with the transmission even if the parking brake pedal is pressed down. I changes the pads in the back and it seems to be a little better, but it's not as good as other Camry's I've been in. Where to look as far as the adjustments go? and possibly how if it's not the usual method.
View 4 Replies
We have a 2005 Toyota Camry, had it since 30K miles/2008, now has 94K miles. Since we have owned it, the brake pedal feel has not been great, kind of mushy. It is the way this generation Camry's are. It gets driven mostly on fwy, so not much brake use. At 92K miles I changed the front pads and rotors, pads still had 30% left on them. The rotors were somewhat warped. Brake fluid has been gravity flushed every 2 years since 2008, last one in 2012.
Now, the problem is when wife drives it, twice at a lengthy red light, she has noted that the brake pedal "almost" sinks. It did not go to the floor, but the level went lower. The car did not move during this events. With the newer ABS brake systems, on all my three cars, after a full stop, I can push the pedal down further, almost close to the floor. The Camry is the same way, just with a baseline of mushy pedals. My wife only drives one of the other ones (Dodge Caravan,)and has not complained about that one.
The brake fluid level is solid/steady, no leaks at the wheels either.
Now looking at whats involved, seems I can change the master cylinder myself. The question is do I need to? I don't mind paying a mechanic to do a diagnostic too, just not sure what they are going to do. I believe, just as a defensive measure, they will go ahead and change the MC (which then I might as well do it myself). I could also continue to drive it, but don't want to be stupid here.
View 10 Replies
I have a 99 Toyota Camry and recently the breaklight has been coming on and off sporadically. I assumed I had done some damage to my E-break, as the other week I tried to back out with it on (cut me some slack, I just moved to PA after having only really driven in FL lol). I wasn't worried about it since I didn't notice any issues with my breaks, however the last few days I randomly have to press the pedal down almost to the floor to come to a full stop. There doesn't seem to be any consistency to this, sometimes it happens when the light is on but usually not. It does it both when I am stopped (causing me to move forward slightly till I depress it farther), sometimes when I am stopping normally, both when I'm going straight and right after turning, ect.
I checked my break fluid level and it is at the minimum line so I doubt that is the issue. I did some research and saw many saying that it was likely just air in the lines and that the system needed to be bled. But some also mentioned replacing the master cylinder so I wanted to see what response I might get on here (I don't know very much about cars myself).
View 19 Replies
When I press on the brake pedal, at about halfway point, I feel a clacking sensation instead of a smooth downward motion. When I let my foot off the pedal, I feel the sensation again. There also seems to be a small knocking sound when I feel that clacking.
In terms of braking, there's no issue. It's just a minor annoyance that's been bugging me for a while. Camry 2012.....
View 6 Replies
The clutch on my 2003 Toyota Tacoma has been acting funny for a while. I have to pull the pedal back up with the top of my foot about half the time, otherwise it acts like the clutch isn't all the way disengaged when I push the pedal to the floor. The master and slave cylinders have both been replaced as well as the clutch pedal mechanism itself (thought it might be the spring). I adjusted the push rod a little bit and it seems to have worked slightly but it's definitely still a problem.
View 3 Replies
I have the limited with the push start. In order to start the car, you have to push the brake in so far and then push the push button. Lately the brake pedal is really hard to push down after its been sitting for an extended period. Once its started, all is fine. Its almost like I've pumped it a few times first, but its not the case.
View 11 Replies
I drove my 2005 Prius 2 hours and parked it for 5 hours. No problems on the trip down. I got back in it and it started up just fine. I was sitting in the parking lot with my foot on the brake (hadn't moved yet) and the following occurred:
The brake pedal seemed to push back on my foot
The red exclamation point illuminated
The yellow exclamation point illuminated
The ABS light illuminated
The VSC light illuminated
The red parking brake light illuminated (not shown)
All of these lights point to the skid ECU. It seems like my skid ECU is toast or something called the ABS & BA & TRAC & VSC Actuator is an issue (never heard of it but I see it connected to the skid ECU). I did a visual check of what I could and everything seemed in order. I pulled a bunch of fuses and I didn't notice any that were blown. (I didn't pull them all but will tomorrow)
After not finding anything, I drove back home. As expected, I had no regen but the bigger problem was that I had no power assist on the brakes. A few times I actually did skid and the car brakes really bad without regen or power assist. If it was raining or snowing I could definitely see a hazardous situation.
I'm kind of at a loss here. Tomorrow I'll pull the kick panel down and see if the skid ECU is getting power but I can't think of anything else that would cause this situation.
View 19 Replies
I have a 2010 Prius Hybrid and lately, on an intermittent basis, I will press the brake pedal and push the start button and the dashboard lights up as normal but when I go to put it in gear nothing happens. The last time it happened the fan was running and I couldn't turn it off. It's like the car is all set to go but all the interior controls don't function. I then shut it off and restart it and everything works.
View 1 Replies
Last night I jumped into my Treg to move it into my garage. When I pushed the brake pedal to move the gear selector out of park, I heard a whooshing sound. Like the sound of a bellows-type foot pump I use to inflate my dinghy. I could also feel a slight amount of movement in the transmission lock button on the top left side of the shifter when doing this.
Now I'm noticing this noise whenever I apply the brakes. It doesn't appear to affect braking performance, but does have me wondering. I'll have the dealer check this out when I take the Treg in for the recent recall (got my notice yesterday).
View 14 Replies
I've been noticing severe power loss lately . I know the 12 camry i4 has a bit of lag when acceleration but it's a bit worse now . I do have weapon r header , injen intake and magna flow muffler. I've cleaned the intake filter but sometimes the car feels as though it doesn't want to go then it does. I have to push the pedal down hard . I also have res delete.
View 9 Replies
Recently my clutch started acting strange, the pedal felt softer and eventually after I pressed it in it stayed on the floor. After pumping it, everything went back to normal. Next day, still same thing, no pressure in the clutch pedal. I checked the brake fluid and it's full. There is also no sign of any leak. Took the car to the mechanic, he recommended changing the master cylinder. I changed it but still nothing. I tried bleeding the slave but every time I bleed it, it has air in it. So I'm stuck and don't know what should I do next. I think it might be my slave cylinder but I don't have a place or tools to do it myself. I'm pretty sure the entire tranny needs to be pulled out to remove the cylinder. I also read that most people change the clutch when they replace the slave.
View 10 Replies
We just got our 2012 Camry XLE about 1 month ago. Today, the smart key push start didn't work; the brake pedal seemed like it was seized, but the green (key) light did manage to come on, indicating it knew the key was there. When I pressed the start, all of the dash lights were flickering, but the car wouldn't start. Was towed to the dealer, who ran a diagnostic that indicated the battery had failed (the options for the diagnostic are pass, charge, and fail). They installed a new battery and it seems fine.
One of the doors wasn't completely closed overnight - would this have caused the battery to be done? I could see if it caused the battery to drain, requiring a boost / charge.
View 14 Replies
My question is this...when my foot makes contact with the brake pedal there is about a quarter or half inch of "space" where I can push the pedal forward before you can feel whatever the pedal pushes against make contact and begin applying braking.
This dead space area will always activate the brake lighting but until you reach that next part under the dash somewhere no braking occurs.
I am quite used to driving my 2010 and this doesn't occur....can not remember if the 99 has always done that and i just realized it or if this is a new issue.
Brakes and stops great with and without load. No issues otherwise. Pedal pops out quickly and normally when taking your foot off.
View 1 Replies
I have a 2001 F-350 Diesel 4x4 crew cab 8ft bed dually 7.3 diesel 6 speed. The issue is that the parking brake pedal is extremely hard to push. One day it pushed down and ratcheted into a locked position as normal and the next day I couldn't push it more than an inch down. I have rear disc brakes with internal drums in the rotors for the parking brake assembly. I replaced the shoes and hardware (which were fine) and I still have the same issue. I removed the front single cable from where it splits into the two rear ones and the foot pedal depresses smoothly and with the touch of a finger with no load on it. What else is it? The only other thing is one of the rear cables unless I am missing something?
View 5 Replies
