Golf IV / Jetta IV :: 2001 VR6 Hard To Shift And Cannot Get Into Any Gear When Engine Running
Jul 28, 2014
01 jetta vr6 5 speed. Alright so earlier today I pulled out the driveway. (Hard) was in 1st gear around 3 or 4 grand and I stomped it. Got to 6 grand and hit 2nd. Took 2nd to 6 grand and let of around 60 mph. After that I short shifted into 3rd, 4th, then 5th. I noticed going into fith was hard. Had kinda rev match to get it. I stayed in 5th till I got to my destination roughly 4 miles. When I came back out to leave I had a hell of a time getting it into reverse. On my way home it was extremely hard to shift and now when the car is running I cant get it into any gear. This is what I did.
Car shifts fine with car off.
Car will not shift with engine running.
When started in gear with clutch depressed I can still let the clutch out and stall the car.
When starting car while in gear with the clutch NOT DEPRESSED the car jumps forward.
I can figure it out ove tried re adjusting the linkage. Nothing.
View 6 Replies
Advertisement
Background facts:
Tranny swapped from my 4 speed auto to a 1.8t o2j 5spd
13lb. Light flywheel
Powerflex dogbone mounts
Peloquin LSD
The problem: Very hard to get a smooth shift from gear to gear. Trust me, I know how to drive, but I can always feel the car shifting into a different gear if you know what I'm saying. On my friend's bone stock Jetta, I just let the clutch out without gas in between shifts and you don't feel a thing.
On my car, you feel EVERYTHING. People have told me the light flywheel will make the ride more uncomfortable in many ways, especially since the RPMs drop much quicker in between shifts than stock.
View 9 Replies
My buddies Jetta won't shift into high gear. I am going to take a look at it this saturday to find more out.
View 4 Replies
Got a 2001 Jetta 2L automatic 200k miles with gremlins. possibly multiple unrelated problems. First problem that presented is that the transmission will occasionally not shift into 4th gear. I discovered that if I stop the engine, then restart it, it will again return to normal operation, hence the thought that it is electrical. After a year or so of this, second problem pops up: the engine will die while the car is driving, or some times idling at a light. I've also noticed that the interior lights flicker somewhat in intensity when on and the engine is operating, so there could definitely be a grounding issue somewhere. I have heard that the ECU/ECM connectors could become corroded, but haven't yet dug into it to look. Any guesses as to where to begin?
View 2 Replies
Could my brake issue be related to my transmission problem? Neither are constant. Brake problem= sometimes the brake pedal feels hard, like there's no power brakes (I drove a car once. ..looong time ago. .. that had no power brakes or steering) but it will kick in after a short distance. Transmission prob= seemingly unrelated, is a problem shifting from 1st to 2nd gear. This has happened maybe a 1/2 dozen times, the first time and mostly when in heavy commute traffic and when going between 1st and 2nd gear because of the slow commute speed, but also at other times when not in lengthy slow commutes. When it doesn't shift, the odometer doesn't work (shows only dashes) and an engine light comes on (the sprocket/gear looking one). Usually the transmission will eventually shift and the light goes off.
I read that the brake problem might be a vacuum hose problem? Something about a booster? Is this dangerous? or is it like having a car w/ no power brakes? Going to have my transmission looked at this week. Read on another site about dropping valve seats on this year car. If there's a major transmission problem, I'm wondering if it's worth fixing? I changed, timing belt, water pump, front and rears brakes, tires. 143,000 miles.
View 1 Replies
My Santa Fe 2001 model V6 4X4 Automatic shift gears down hard from 3rd in to 2nd. I checked transmission oil and its light brown. Should I drain and refill or not worth it.
View 7 Replies
I have a 2002 Santa Fe V6 2.7 liter, FWD, 215,000+ miles. When it shifts from 2nd to 3rd the whole vehicle jerks. It does not do this on the other gears. I took it by a transmission place for a free scan and they said the transmission is fine.
View 19 Replies
So i was trying to adjust my freinds shift linkage on his o2j and i got a little ahead of myself and forgot to put the shift tower in the home position before making the adjustment. after i realized you can't shift into second ( either that or 2nd and 4th are extremely close together now and feel like the same gear ). I try to get it in home position even with the cables off ( did this for experimentation) and still wouldn't go into home position...meh. still have all the other gears including reverse .
View 4 Replies
I just finished the DG install yesterday. I am having a real problem with the first gear: it is really hard to shift into it (I mean hard!) - and several times I went into 3rd believing it was in 1st, while driving. I know that the DG is notchy and a little stiffer (which I like) but this does not feel right. I have to really push hard (moving slightly toward reverse) to shift into 1st. My wife would never be able to find it or shift into it (not that I let her drive my R that much...).
Note that all the other gears (2,3,4,5,6 and reverse) shift beautifully without any effort with that nice click. But not 1st.
What is it? Adjustment? I did it twice. I made sure that both cables were "all the way in" before tightening the first two bolts (and I made sure that the cables were not moving - a common problem with this install) with the engine lock on and pin in.
View 22 Replies
So last Thursday I started my car up in the blistering cold and it ran fine for about a minute and started to misfire so I shut it off. It hasn't ran since. When that happened the check engine light was blinking because of the misfire. I didn't have a code reader at the time to read it. now that I got a code reader the damn thing isn't throwing any codes. it spits and sputters sometimes. I've had no previous problems with the car. Thinking It might be a weak fuel pump or bad coils and in not sure how to test them.
View 1 Replies
2011 TDi 6 Speed (Sportwagon) with problems shifting into 2nd? Mine is currently in the shop under investigation for a balky shift when cold. The tech says it's not right, but then they find another vehicle in inventory with the same issue...currently waiting on a VW engineer.
View 16 Replies
I have a 2001 Elantra GLS, 160,000 miles. These two codes come up on ny diagnostic tool.
P0422
Main catalyst efficiency below threshold (bank 1)
No symptoms at all
P1529
Customer snapshot request
Symptoms
Car will shift hard into third gear and stay there without shifting at all regardless of speed. Shutting the car off and restarting will sometimes fix, but only temporary. When car runs normal, it runs fine and shifts good. At speeds around 40 it seems to kick back and forth between 3rd and overdrive as if it can't decide where to be. Tried replacing speed sensor, but new sensor did not fix problem.
Fuel Sys 1 CL
Fuel Sys 2 NA
Calc Load 18.4
ECT 201
STFT B1 0.0
LTFT B1 -2.3
MAP 8.6
Eng RPM 3351
Veh Speed 22
EV flashing
O flashing
View 17 Replies
Over the past few weeks, my car (2002 Golf 2.0L) has gotten really hard to shift into 1st and reverse (has crunched once or twice), but only when the car is hot, after driving it for a little while. When this happens, and I try to shift into reverse, the shifter feels really "sticky" and can get kind of stuck in the depressed position near reverse.
I bled the hydraulic system and replaced the slave cylinder, but no dice. I haven't noticed any clutch slipping. Shop wants to replace the whole clutch. Is this the right answer?
View 5 Replies
Passat wagon, 2002, 1.8 T engine, 68,000 miles Auto transmission. When I start engine the two warning lights stay on, and then I shift into gear the engine jolts hard. I have parked it for now to learn more about what the problem may be. What is Anti-Slip Regulation and what does it mean when the indicator light stays on?
View 2 Replies
When it gets hot outside and the car warms up (15 mins or so of highway driving), the stick gets extremely hard to move and it doesn't go back to center when it's out of gear. So I could push it all the way left or right without putting it in a gear, and it would stay there, it wouldn't pop back to the center like it should. It becomes really annoying and difficult to drive because it gets so stiff and hard to move, what could be causing the problem? I've already adjusted the shift linkage and that didn't work.
View 3 Replies
My 03 Gli 24v manual transmission has been acting up lately. First it started to get a little difficult to shift into gears about a week ago. Then tonight i was driving through a parking lot in 2nd, and after i came to a stop i tried to put it back in to first and it would not go into gear. As i was trying to get it into 1st i could tell it was grabbing a little bit and the car was inching forward.
I got it to a parking spot and starting reading about other peoples issues, one i read said they were able to get it to move after pumping the clutch some. After trying that i was able to get it into gear and drive it to my parents. Looked at my brake fluid and its full. Took it for a test drive around the neighborhood and it was shifting fine at first then started getting a little difficult to shift again. I tried taking off in 6th and it stalled. I tried going from 1st around 3k-4k rmps to 6th and it was still driving with very little lugging. My clutch feels and is still stiff, not loose at all. I do have to go all the way to the floor with the clutch before im able to shift
Finally to my questions. Could my clutch be going bad? Could my cables need adjusting? Something I read about a pressure plate maybe?
View 5 Replies
Started noticing an issue with my trans awhile ago, the other day it stopped shifting out of first when cold. It's a 1.8T auto 5 speed tiptronic, it's the Jatco 09A. I know the shifting problem is the solenoids and it doesn't look that hard to swap them out. The trans shop said it looks like there is slippage on gears 2-4 and the fluid is toast. Looking at replacing or rebuilding, shop said 4-5 grand, how easy would it be to swap in a used trans? And what kind of issues would I be looking at?
View 1 Replies
I replaced the old auto trans that was slipping in my 2000 golf with a same year auto trans from a beetle. The beetle had 115k miles and the PO toasted the 1.8t. I replaced the TCM also and when I finished the install I took it out for a drive this afternoon and when I shift it into drive it starts out in 3rd. It will manually shift through the gears but it will not shift from 3rd to 4th. Could I have left something unhooked? Is this a solenoid issue?
View 10 Replies
This truck has been giving me tranny problems for a while now. About a year ago, stopped in traffic in neutral, I attempted to shift into 1st but it wouldn't go into gear, not reverse, not any gear. Eventually after a minute or so of trying it reluctantly went into 1st. About 6 months ago I started the truck after being parked and again it wouldn't get into gear. Shut it off, tried to get it into gear, nothing. Checked the hydraulic fluid reservoir for the clutch and it looked a little low so added a bit and after that it shifted into gear (maybe coincidentally). Now about a month ago, it again wouldn't shift into gear after being started. I checked the reservoir again, looked fine this time. Shut the car off, attempted to shift and this time shifted with ease
Something that I've noticed in the past year is that sometimes now when I shut the engine off it doesn't run down smoothly; kind of slows then clunks to a stop. Didn't used to do that.
View 2 Replies
I just replaced my injectors in my 12v vr6 and now having some problems. Mainly having issues with start up. Having to feather the gas to get it to start and still runs rough for a min or two.
View 3 Replies
When I'm driving, the Jetta will sometimes not shift from 3rd to 4th gear, so I just turn of the car a start it and it seems to work, but eventually does it again. Once it is in 3rd gear it does not downshift and stays in 3rd even when stopped. The trouble code is P0785 which is the shift/timing solenoid. Not sure if I need to get a new part or which solenoid to get. Also I cannot figure out where this solenoid is actually located or what it looks like.
View 1 Replies
