Toyota - Camry :: 2002 - Misfiring / Shaking When In Idle Or Going Slowly
Feb 9, 2012
Took this car for scheduled maintenance, tuneup on 12/19. AFTER the tuneup, it started shaking when in idle or going slowly. Took it back 1/5, they confirmed it was misfiring, checked a computer code, replaced one of the coils. The misfiring went away but returned, worse than ever, last week (early Feb).
I read somewhere that replacing coils for misfiring can be just treating the symptom, not the cause. What should I do now?
View 13 Replies
Advertisement
In my 4 runner when I slowly accelerate between 30 and 40 mph just as I can hear the car about to shift gear the car begins to shake when I than accelerate the shaking stops. Brought it to a shop and they changed a spark plug and coil they say was mis firing, but I pick the car up and the problem is still there. Their diagnostic shows no problems, yet the shaking is still there when slowly accelerating between 30-40, no check engine light has ever come on. While it shakes if I shift the car from D to 4 the shaking stops, and if I speed hard through 30- 40 it doesn't shake, just when I slowly accelerate.
View 5 Replies
My car has had random misfiring when at idle and has been shaking really bad but once I accelerate and get up to speed the vibrations and misfiring stop but the check engine light flashes for a few minutes. I have changed spark plugs, all 6 ignition coils the intake manifold gasket and both camshaft position sensors. My car has 180K the codes that are showing up are 300,301,303 and 0016. I really love the car and have had no prior issues the car before this ran like a champ.
View 2 Replies
My 99 Explorer XLT V6 SOHC has been misfiring lately. In idle the RPM needle fluctuates a bit and the vehicle vibrates and shakes. At night when the lights are on I notice them dim a bit as the engine struggles in idle. It doesn't stall very often at all. Accelerating I notice way less power and the engine studders. That's when the engine light comes on flashing. Then remains on solid afterward. I brought it to a mechanic friend who read the code and it was cylinder two misfire as well as the O2 censor.
I replaced the plugs and leads and censor. Noticed the plug in cylinder two had little to no gaping. Thought I had fixed the problem. The vehicle ran perfectly. Three or four days later driving on the hwy same problem came back. Thinking it must be the coil pack I got one for a good price and replaced it. Again, the truck ran great for four days and now the problem has returned. Same thing, shaking studdering and flashing engine light. I have verified the locations of the wires and plugs a few times so i believe they are all properly installed.
View 1 Replies
My 99 Explorer XLT V6 SOHC has been misfiring lately. In idle the RPM needle fluctuates a bit and the vehicle vibrates and shakes. At night when the lights are on I notice them dim a bit as the engine struggles in idle. It doesnt stall very often at all. Accelerating I notice way less power and the engine studders. Thats when the engine light comes on flashing. Then remains on solid afterwards.
I brought it to a mechanic friend who read the code and it was cylinder two misfire as well as O2 censor. I replaced the plugs and leads and censor. Noticed the plug in cylinder two had little to no gapping. Thought I had fixed the problem. Vehicle ran perfect. Three or four days later driving on the hwy same problem came back. Thinking it must be the coil pack I got one for a good price and replaced it.
Again, the truck ran great for four days and now the problem has returned. Same thing, shaking studdering and flashing engine light. I have verified the locations of the wires and plugs a few times so i believe they are all properly installed.
View 7 Replies
Our 2002 Camry is in very good condition with ~75k miles. The other day we went to start the car up and it wouldn't turn over. The car would turn a couple of times and then start clicking. We jumped the car and I hopped in to take it to our local mechanic. I instantly noticed during the entire trip to the mechanic that the idle was very slow and chugging. Like it wanted to die anytime I was stopped.
I got to the mechanic and pulled in the lot. The car died. However, I was able to start it up again with no issues. A day later I get a call from the mechanic telling me that they had no issues starting the car whatsoever. They said the battery was a little weak so they replaced it (it was the original battery). I was also told that I might consider changing the spark plugs in the near future. Otherwise they said the car was running great.
After getting the car home I am once again noticing the low/chugging idle. It doesn't seem anywhere near as bad as before, but it is there sometimes.
View 6 Replies
2002 Toyota Camry
2.4 V4
My car has developed a rough idle when stopped and when accelerating. When I got the CEL, I had the codes read at Advance Auto.
The codes are P0301, P0302, P0303, P1349.
View 1 Replies
I just recently purchased a used taurus and was experiencing rough idling and misfiring during operation. I replaced the EGR valve, the egr sensor, coil pack, spark plugs, iac valve, as well as check for vacuum leaks near all the hoses. I am a novice when it comes to this, but I was able to change those without issue. The misfiring was fixed during driving, but I still have rough idling. The needle seems to stay in check pretty well and the check engine light isn't on, but the car kinda hesitates and it causes the car to rock when idling. You can also feel the stuttering and rocking when cruising at very low speeds (5-15mph). I've already plugged in a decent amount of money into parts and am running out of patience when it comes to fixing what is a "potential" problem, and it winds up not fixing much.
View 5 Replies
I recently picked up a 2wd 2002 F-150 with a 4.2l V6 that has just over 300k miles. The CEL is on and I'm getting P1131, P1151, P0316, P0305 and an occasional P0301. It has a very distinct misfire from around 1,000 rpm and smooths out between 1,500 & 2,000 rpm, the idle rpm occasionally bounces (sometimes enough to stall), and the idle is sometimes rough.
I have replaced the plugs, wires, fuelfilter, and replaced a leaking PCV hose. As I have changed things the symptoms have improved some but they are still there. While capturing some livedata it kept going out of CL and into OL Fault. When it would the idle quality was crap and the miss was much more significant. I would have to put it into D hold the brake and run the RPM's up to just over 1k to get it back into CL.
After I got done with the data stream at idle, I set the parking brake held the foot brake and put the truck in D then ran the rpm's up to around 1,200 & held it there. The truck stayed in CL but it would cycle between misfiring for 5 - 10 seconds then clear up and run smooth for 20 ' 30 seconds, every time it cycled there was an audible click that could be heard. Also, the AC was off the whole time.
Live DataStream @ Idle: CL
CalculatedLoad Value - 12.9- 14.1%
EngineCoolant Temp - 103degrees C
Short TermFuel Trim B1 - 32.8%
Long TermFuel Trim B1 - 0.0%
Short TermFuel Trim B2 - 32.8%
Long TermFuel Trim B2 - 0.0%
Engine RPM - 816 . 846
[Code] .....
View 14 Replies
I bought my 2012 Camry, with 12,000 miles from the Dealership in December of 2013. The car was sold as CPO, car was purchased on Dec 30... just 6 weeks ago and I have had numerous issues with the car Misfiring. When I arrived at the dealer, the CHECK ENGINE and TIRE TRACTION lights are one and the car is running very rough as acknowledged by the service techs. For the 2nd time now, I am told they are not able to recreate the problem, so they are not able to fix it.
This is my 4th Toyota and I have NEVER had this many problems with a Toyota. Did I get a lemon? Service tech says he can't fix it unless he knows exactly what's wrong. I am asking him to check the spark plugs, check the ignition coil...and his response is that they can't just go on a wild goose chase, they need to know what they are looking for. Does this sound reasonable?
View 17 Replies
My 2000 Toyota Camry V6 died while driving the other day. At the shop they were able to start it but said it was misfiring but it didn't cut off when they were driving it. They recommended a tune-up to replace spark plugs and "wires" but admitted they weren't sure what the problem was. I haven't had a tune-up in awhile, actually not sure when the last time I had one was (if ever!). Would this cause it to die while driving?
Should I invest in a tune-up even if it doesn't fix the problem?The battery is about 3 months old. The master and slave cylinder were recently replaced (about 6 months ago), timing belt and water pump and hoses were replaced a couple of years ago.I have high miles, about 260,000 and love this car and have needed very little work and has been a very reliable car. Would love to continue driving it!!
View 4 Replies
My mom wants to sell her 2002 Ford Explorer w/ 4.0 as enough kids have moved out that the vehicle is no longer needed. It has 162 000 mostly trouble free miles on it. However, for me to sell it for her, I need to get it running well first. The background:
Just recently it fried the alternator. No big deal, got a reman for my dad and he put it in. But now it has this sort of "shudder" at idle and low rpm, and also when accelerating slowly low in the revs. I don't know if it was there before or not because only my siblings drove it, and their not exactly observant. I am positive it is a misfire.
So far I have done the obvious. I have pulled all the plugs, they are nice and tan, re-gapped them (although they were only .002 out of spec at the most). I noticed that one plug wire was broken on the inside, where it connects to the plug. Thinking I solved the problem, I bought a new set of wires and put them on. No such luck however, as the problem continues unchanged. On the new wires, I have verified tons of spark making it through. In an effort to isolate the bad cylinder, thinking maybe it was actually a plug, I started pulling wires off the coil with it running. I could barely notice a change in the engine with any of them, and a couple seemed to have no change at all (again, I may just not have been able to detect it because I could barely make out the other changes).
Next, thinking maybe it was fuel related, I put a stethoscope on some of the injectors and they sounded the same, but I can not get at the back passenger and 2 back driver ones. How else can I test these?
I even went so far as to unplug IAC, engine died immediately so its not that. I also took off the EGR valve and cleaned it, and pushed the plunger up and down lots and it moves freely. I tried pulling off the vaccuum line from the EGR with the engine running and there was no change, but that doesn't really mean anything does it?
So I put it all back together and thats how it sits for the night. On a related note, the CEL is on, but it is on more often than not on that thing, and my dad has taken it to a dealer three times to have codes read and nothing ever shows up. The mechanics keep saying that it has something to do with the fuel cap and pressure or something.
View 9 Replies
My car makes a weird noise/feel when I stop at lights or when we are going very slowly-- its like some motor inside is spinning weirdly-- off kilter-like. This only happens when in drive or reverse; when in neutral and I rev the engine, it doesn't happen. This used to happen only when I drove for long times (3 hours maybe)--and I often could "fix" this by just letting the car rest for half and hour. Now it is happening just after 40 mins of driving. My car is a 99 Toyota V6 Camry.
View 19 Replies
I have an 02 ranger xlt 3.0, it started having a rough idle, codes say cylinder #2&3 misfiring, changed plugs, wires, coil pack, didn't work, still same code, checked injectors on right side, all 3 had ohm reading of 15.8-16.5, the injectors were clicking like they are supposed to, sprayed carb cleaner around the intake ports, didn't change the idle at all,what else can I check or do? with out tearing the engine apart, unless of course I have to, the truck has been very good to me, it's got 205,000 miles on it, I need it to last at least another year...
View 4 Replies
My exhaust system was replaced on my 2005 Corolla in August. After driving it for just a few days, there was a shaking when the car idled. The mechanic replaced two engine mounts and the idle was much worse! He said it was ok to drive, so I started on my planned trip across the country. In Denver I took it to a mechanic at the Toyota dealer and they adjusted the throttle. It was better for a while, maybe a week and 1,000 miles. Now it is worse than ever! Having gotten two totally different causes from mechanics, I am not sure what to do next.
Also just before the exhaust sytem went, I had the 60,000 mile service done and had the car totally checked out by both Toyota, and an independent mechanic who specilizes in Japanese cars. After a car wash in California, the maintence required light came on.
What is going on?
View 8 Replies
I had a problem with my steering wheel shaking at various speeds. Eventually I found a bad inner tie rod and replaced it. The shaking is gone, but whenever I get over 70 mph there is still a very small vibration. I had all 4 wheels aligned after changing the tie rod. Tires are brand new, less than a week old. The mechanic checked my ball joints while doing the alignment and said they were good. Could my struts be causing the vibration? They need replaced, not sure if the previous owner ever replaced them and the car has 225,000 miles.
View 3 Replies
I have been searching and it seems I am not the only one who has a rough idle with the I4. It is very rough even without the A/C on. I can see the dash shaking, I can feel it in the steering wheel, brake pedal, seat, and arm rest.
The dealership cleaned my throttle body and MAP sensor (They forgot to put one of the screws back in the MAP). This is the third time they have cleaned them. When they returned it to me I told them to keep it until it is fixed. So they took it back in and decided that it might be the motor mounts so they went ahead and replaced them aside from the dogbone or whatever it's called.
When they returned the vehicle it was still having the same issue, they told me that its just the nature of the beast and to live with it. Well my neighbor has the exact same car, and yes it does have a SLIGHT vibration in gear but nothing like mine. I can't stand this car I really wish I would have bought something else.
I currently have 70,000 miles and for the last three oil changes I have been running Full Synthetic in hopes it would work but it has made no difference.
Just a note I have had multiple problems with this particular dealer lying to me. They even ripped up my passenger seat and would not fix it they said it was pre existing. I am over the seat I don't care anymore but I am tired of the rough idle. I plan on taking into another dealer but I am hesitant because they told me if there is no real problem I will have to pay in full for the diagnostic.
View 14 Replies
I disconnected the battery yesterday and once I connected it back the car felt like it was gonna turn off and ever since when I'm in a stop it starts shaking. Is their anyway to fix the idle time ....
View 7 Replies
I've been having frequent problems with my car.
Here's the information about it:
200,000 miliage
engine light is on when key is in ignition, but goes off when car starts up
Four cylinder engine
Here's the problem:
Car stalls intermittently
when it is about to stall, when i slow down, car putters a bit, and RPM gauge shakes wildly
when coming to a complete stop, car shuts off completely, and when trying to start back up, engine chokes.
Temporary solution:
I put the car in neutral and floor the gas pedal, then the car works again.
View 1 Replies
Two cars, a Toyota Camry and a Corolla, are shaking when driving them, esp. around 35-45 mph when accelerating. This started right after a historic snow storm in Virginia that brought 24" of snow and temperatures in the teens and a bit lower. Nothing appears to be wrong with any of the tires. The shaking feels like the car as a whole; it does not really come through the steering wheel. We`ve only driven each car once since the storm.
I`m thinking this may be from all the moisture and cold. Does this sound reasonable? Do you think it might work its way out, or do we have serious problems with two different cars on our hands?
View 13 Replies
1989 Camry, 2.0L A/T- 97K mi.- This car has developed a violent shaking condition when traveling at highway speed. It only occurs after the car has been driven for at least 1/2 hour. It does not appear to be related to an individual wheel or axle, and happens only when the accelerator pedal is depressed and the car is in gear and moving at 50+ MPH. Steering is not affected, nor does turning the steering wheel increase or decrease the shaking. The shaking stops when the accelerator is released. The engine runs smoothly, with no misfire or vibration.
View 3 Replies
