Toyota - Camry :: 2002 - Hard To Start / Starter Would Crank Just Fine But Engine Would Not Fire
Jul 1, 2013
Camry 2002 LE (4 cyl Auto), 140K mi
This morning, for the first time I can recall, the car would not start right away. Had been sitting in the garage for 2+ days. Starter would crank just fine, but engine would not fire. No lites were left on overnite. Finally (after about 6+ attempts), engine started -- runs fine now.
Took it to TOY dealer. Their diagnosis: weak battery, alternator low output.Happy, had recently (6 mos) replaced battery after 4 years of use, so got a new battery N/C.TOY ran a charging system check and it shows "Alternator Condition: OK" (midway between shitty and great I recall).
Funny, but my first thought when it would not start was the fuel system (fuel pump) or dirty ignitors. I did ask my regular mechanic for an opinion, and he thinks it might indeed be the fuel pump -- perhaps a clogged filter.
View 2 Replies
Advertisement
I recently caught up on some maintenance with my truck, changed the turbo pedestal seals, replaced both batteries, brakes, e-brake cable etc and installed new 10k hid headlights. its a single cab 250 with a 7.3 and zf6 4x4 with 133k. a couple days ago I turned on the headlights and the truck died, restarted no problem and would die the next 5 times I tried to turn them on, then it worked fine. yesterday I got in my truck to leave for work and got no wait to start light, no glow plug chatter, no fuel pump running. turns over just fine but no fire.
I got a ride to work and tried it when I got home, fired right up. I pulled the pCM, checked it out, no weird smells and my TS chip wasn't corroded or anything like that, worked fine. drove to 711 to get a 6 pack and it did the headlight thing again. I removed the HIDs because this all started after I installed them and reinstalled my silvanias and it didn't die when I turned them on. this morning went to leave for work, same no start condition. I disconnected both batteries for 30 seconds to reset anything and same problem. I was about ready to light it on fire this morning.
View 1 Replies
My girlfriend has a 2003 f150 4.6lt pick up its a great truck most of the time. Problem is when the temp gets in the neg double digits it becomes very hard to start it cranks fine but doesnt want to fire. When it does fire it might stall a few times before it stays running. The last cold snap we had I replaced the battery and in the summer the starter got changed. I have heard that this model of truck are known for hard cold starts. I am just wondering if this is true and any other thing besides block heater. It is strange that my 89 gm pickup will start no matter what temp and I'm having problems with the newer truck.
View 1 Replies
Replaced battery. It seems to crank fine and I can definitely hear the pump kick in for a couple seconds at first, but just will not start. It sat for several days in cold weather. Based on what I have read here I am thinking it is the fuel pressure, and that I need to get the tool to check that. There is about 1/4 tank fuel now, it seems that once before when it sat for several days around 1/4 tank it started and ran rough, then ran fine after I filled the tank. Could it be as simple as filling the tank?
View 14 Replies
My 2001 Accent GS (1.6L DOHC) wouldn't restart after a short 2 mile trip to a local store. The engine cranks fine but doesn't fire.
It has had a CEL issue for awhile and after it wouldn't start I checked the codes and got:
303
335
722
I replaced the Crank Position Sensor and Fuel Filter but it still just turns over.
I hear the fuel pump run when I turn the key on and I broke the fuel line and it is Pressurized, so I doubt it is a fuel issue.
The 722 code indicates the output speed sensor has an issue. Need to know definitively if that sensor is completely shot could this prevent the ECU from firing the engine?
I have had this car since it was brand new and I'd like to keep it going a little longer.
View 5 Replies
2002 Jetta GLS 1.8T (engine stock except diverter valve) 171k miles
It's done this a couple times now. Both while raining out/high humidity. Prior to this, I could hear the pump "growling". Sounded like maybe starting to go. You could hear it prime when opening the door or turning the key forward but would stay sounding like that even when the car was started. Without the radio, you can hear the pump running.
1st time- The car will crank without issue but never start. I let it sit a few minutes, turned key, heard it prime,tried again, started right up like there wasn't an issue and I couldn't hear the pump this time while the car was running.
2nd time-The car will crank without issue but never start. I let it sit for an hour, opened door (couldn't hear prime), checked fuse 28 (good). Figured wth, let's try anyways. Turned key, couldn't hear prime, started right up. WTF. cold idle normal (1000-1200rpm), light revs to 3000 ish normal. Turned off car, let sit for a minute. Turned key, heard prime, car started without issue and I couldn't hear the pump again while the car was running.
My dad is thinking to replace the pump right away. Is there anything else to try? The relay is working... at least sorta. With the somewhat intermittent issue, where to start? Either way, relay or pump, I will be replacing fuel filter.
View 3 Replies
'99 Yukon. Starter spins engine fine but engine won't start. Spray a quick shot of starter fluid or drip some gas on the air filter and it starts fine. After sitting idle for a half hour or so the situation returns. Car will run highway speeds (70-80mph) fine and will handle stop and go in town. Local mechanic wants to replace the fuel pump, which was replaced a couple of years (30,000 miles) ago. This seems an expensive first step with no diagnostics done.
View 4 Replies
I have a 97 chev c/k. 305 vortec 5 spd manual with starting problem. If I turn key to crank it will crank with normal starter sounds but not fire. If I crank for less than 2 sec and release key it starts. Found this when cycling fuel pump to build pressure. Has spark when cranking but not starting. Runs great once started. Truck has 58k (low) miles, all orig.
View 8 Replies
Car was fine, then wouldn't start one day, after driving fine a couple of minutes before. Did this a few times previously, just tried a few times then it started again. There is no cranking when I turn the key, just a click. Lights work fine, stereo etc, no dip in power when turn key. I assumed it was starter motor so took it out and tested it - fine. Also tested battery - fine. Looked at a spark plug, fine, oil level fine. Don't see a reason the engine should have seized, as it was driving just fine, then wouldn't start suddenly, but I haven't tried manually turning the crank. I then looked at the switch on the clutch pedal that gets pressed when you push the clutch in, and allows it to start. Looked ok, but pulled the wires and bypassed it with a cable. Still nothing. Can the starter test ok but still be bad? Toyota Corolla 2003 80,000 miles ...
View 19 Replies
I replaced my starter with a new one from car quest yesterday, it was starting to turn the engine over slow. I checked the batteries, they were fine, so went for a new starter. After installing, the new starter turned fast and fine, started the truck ok, but I noticed a fast clicking sound from under the dash. Ran it home and tried to start it up this morning, turns over fast, the clicking sound is still coming from under the dash, but the engine won't fire. Just turns over. When it's turning over the check engine (and all the other dash) lights flash.
View 3 Replies
Any explantion for how a "bad" starter motor can crank the engine, but use too many amps in the selenoid circuit?
I had this problem when I installed a rebuilt starter motor in an early 1990's Toyota Corolla recently. It was one of those offshore rebuild starter motors. When I installed it, and turned the key to start, nothing. ARRG .. I have to take it back, and it takes me about 2 hours to install it, and another 1 hour to remove it! It's not like changing a lightbulb!
Anyway, first off, before removing it, I checked the voltage (that comes in the smaller cable from the ignition switch,not the one in the thick cable direct from the battery) right at the starter selenoid, and it was only 8.6 volts. At first I thought it was a weak battery, but the battery voltage was 11.8 volts under the same load at the battery. And the voltage at the ignition switch was 11.6 volts. It was loosing 3 volts in the wiring path from the ignition switch to the starter motor! Then I noticed the wiring harness was getting warm that held that wire. Oh Oh.
For the life of me I couldn't figure out what was wrong. Unwilling to throw in the towel and remove the unit, I decided to completely bypass the ignition switch and the entire wiring harness, so I wired it up with my own switch I bough at Radio Shack and my own 16 AWG (the wire in the harness is 18 AWG) wires clipped direct from the battery to the starter selenoid. This is all from the front of the car. I just wanted to see if I could get it to turn and crank the engine. It worked, it cranked ok and everything, but the second time I tested it with this experimental configuration, it melted my 10 Amp Radio Shack switch! The switch was supposed to be able to handle 10 amps! Remember, this is the selenoid circuit, not the main power circuit from the battery.
So I then DID throw in the towel, and took it out, took the starter motor back to the auto parts place. ( I had a little dust-up with the parts place manager; he at first refused to refund my money. He wanted me to take another rebuilt one, but I'd lost trust in their rebuilt units and I just wanted my $$ back. We compromised on a voucher for future purchases.) Anyway, the parts place tested the problem starter motor I had returned to them, and they said it tested "bad". So the one they sold me was indeed no good. (Why they didn't test it before they sold it to me is another question.)
But here's the mystery: If the rebuilt starter motor tested "bad", and it indeed was "bad", how could it have cranked the engine with the experimental heavy guage wiring ? Any explantion for how a "bad" starter motor can crank the engine, but use way too many amps in the selenoid circuit?
View 14 Replies
I just picked up an 02 Supercrew. It came with a “Ford” remote starter. I imagine it was a dealer install for the previous owner. Anyways when I try to use the remote starter, it will crank the engine over but not fire. If I manually start the truck it fires up immediately. How come the remote start wont fire?
View 7 Replies
My wife has a 2002 Thunderbird. Sometimes it won’t start when you turn the key. I don’t mean it doesn’t crank or cranks slowly, nothing happens. You can hear relays clicking but obviously no power is getting to the starter - the lights don’t dim when this happens. We’ve had the starter motor replaced. My mechanic is baffled. Sometimes this happens hourly, sometimes it will go weeks without happening – it’s been doing this for at least a year. To get it started, you just need to sit there and keep turning the key 10 to 40 times. It will eventually start. She just informed me that sometimes she shuts off the car in something other than Park, them moves to Park. Can this mess up the xmission lever position lockout to cause this? How can it just start by turning the key, only, multiple times? Remember, you can hear relays clicking when the key is turned.
View 19 Replies
A cold engine crank will turnover and start normally. But stop to run and errand or grab lunch...and the warm 302 2 barrel engine will turn over very sluggishly, lke the battery is dying. If you wait until the engine is cool, an easy start is assured but that takes hours! A local repair shop has rebuilt the carb, the battery & cables are new, and the starter works fine when engine is cold. My local repair shop is out of suggestions. It seems to work a little to hold the gas pedal down on the floor for a warm engine start....but engine still turns over sluggishly when trying to start when warm. Now If I drive it.....I just drive it around town a bit then back home ...unless I stay several hours somewhere while the engine cools....but that's not fun. It is a convertible, fun to drive...and this problem needs to be solved.
View 14 Replies
1997 Toyota Camry V6. The car won't start, the engine won't crank. I've checked for 12v constant at the starter and that's good. Next I checked for a 12v trigger at the starter. That wasn't present at the starter.
I went to the starter relay. Pulled the starter relay and tested it by applying 12v across two terminals and checked for continuity across the other two. It checked fine.
So I checked for constant 12v into the starter relay, that's present. Checked for 12v trigger into starter relay, that was present also. Next I jumped 12v through starter relay terminal into the starter and the starter cranked the engine. Next I checked for ground into the starter relay, I didn't have continuity.
So I'm guessing it's either a bad ground wire coming into the fuse box or maybe even a bad fuse box? Is my thinking correct? Or is there something else that it could be? Maybe a main fuse or something, IDK, this is the first time I've encountered a problem like this.
What wire is the ground source for the starter relay? I found a wiring diagram from Chiltons (which I've attached to this post for reference) but I'm not really sure which wire is the ground for the starter relay. I don't have the car or relay in front of me to look at the terminal numbers.
View 12 Replies
I have an 02 f150 5.4 4x4, drowned it a while back, thought i had hydro lock, crank can be turned by hand though as far as i can with a wrench, so internals seem to be fine, no bent or broken rods that i could tell, ripped everything apart cleaned it up put it back together, new fuses, new ignition relay, new starter, alternator and battery as well, turned the key to on and got all my electronic stuff back up, turned to start and it all goes dark, which i assume is because at that point its sending power to the starter, but the starter didn't turn or crank the engine...
So question being when i put my new starter on is it possible that i might have crossed a wire or something that would cause it to not crank? and due to the fact that I had water in it, and had hydro locked it, all my plugs are out, now I know that spark is needed for the engine to run, but shouldn't be needed just for the crank to turn right? question being is that once i fix the wires on my starter, I am looking for initial crank before start up, so do i need to put a plug or two back in and hook them up to make it crank? or will it crank without them? and yes I did replace all my fluids as well.
View 8 Replies
My 1987 Toyota 4Runner 22RE has a weird cold starting issue. When the temperature is in the low 30s F or below I have to use the gas pedal when I first start it (for only a few seconds) in order to make the starter disengage. If I don't push the gas pedal it chugs at around 250 RPM and the starter remains engaged. If I kick in a little more gas (up to about 1,500 RPM) the starter will immediately disengage and then it runs just fine at around 800 - 900 RPM.
When it's warm out (40 F or higher) it starts up and runs perfectly without any of the aforementioned happening.
Maybe related is the following: when the weather is warmer out this SOMETIMES happens: the engine idles too high (1,100+, sometimes up to 1,700). If I "kick" the gas pedal this usually knocks the idle back down but not to 750 - 800 where is should be.
I have thought about replacing the (I think it's called) idle air control valve (the big metal thing with the flappy gate inside) that sits atop the air intake above the driver's side headlight I want to replace this only if it's going to fix it.
View 1 Replies
I need to know the Fire order for the 2011 toyota camry se 2.5 L engine. so I can find which oxygen sensor I need to change. I m getting a P0137 code and it said is the bank 1 sensor 2. I think that is the one after the catalytic converter but need to find out for sure.
View 1 Replies
2002 F450 7.3 Turbo
Ok first problem : Starter Motor fuse kept blowing and I spent weeks trying to figure it out. No luck. so wired up a push button just to get the truck started, its a work truck so it was needed asap.
2nd problem : he truck stopped starting completely. Wont start in Park or neutral and after a NEW STARTER (because I thought the solenoid on the starter was bad I replaced it) Everything work correctly for one start with the key. After the second time trying to start it blew the starter fuse again. So I tried the straight wiring to starter. still nothing. I was wondering if there are any shims or anything at the transmission housing to correctly position the starter. I am thinking that maybe the gear is stuck or gets stuck sometimes. when I straight wire the starter it does nothing but the wire gets hot so I know its pulling.
View 3 Replies
Okay so I have a 2004 Dodge Ram Hemi, the truck was running fine all this weekend and was fine this morning. Went out at lunch and used the automatic starter button while walking to it and wouldn't start. It turn over and wants to start you can hear it trying to catch but it won't catch unless you put some starter fluid in. Just changed all 16 spark plugs, all 8 coil packs, wires and 2 valve springs about 2 weeks ago have been running fine since and now this. What it could be?
View 15 Replies
The battery is about 6-month old and my mechanic replaced the starter last week as the car had a hard time to start. Since then it has no problem except once in a cold day (about 35 degrees) it took 10 minutes to get started. Every time I switched the key, no sound came from the starter or the engine, just like what happened with the old starter. But this only happened once. I didn't have trouble in other occasions with the new battery and the new starter. What could be the problem?
View 1 Replies
