Toyota - Camry :: 1996 Frequently Keeps Losing Power To The Spark Plugs
Sep 6, 2012
My old 1996 Camry with 2200 cc 4 cylinder engine, frequently keeps losing power to the spark plugs. I have changed the fuel filter and the ignition coil. That did not work. I also noticed that the car was starting when I unplug and replug the primary wire plug to the ignition coil. So I have replaced the primary power plug with a six inch pigtail and a used plug purchased from a salvage yard. This is not working either. The Toyota dealer near my house want to replace the igniter and the Engine Control Module just to be sure that these are not the sources of problem. The dealer did not test these parts. So I refused to replace the parts without a proper test. I would like to test these parts. Is there a test available for the igniter and ECM that could be performed. I have access to a lot of tools. I need a schematic and/or test to test these components.
View 18 Replies
Advertisement
This past Sunday, I replaced the spark plugs on my 2008 Toyota Camry CE, following one of the sticky DIYs. My car has approximately 107,xxx miles.
Last night on my drive home from work my CEL came on. First time seeing a CEL light since my BMW days, . Luckily, I have a OBDII scanner at home and after running the scanner, it gave me the following trouble codes:
- P0101
- P0172
I went ahead cleaned the air filter (I have an Injen SRI installed).
After doing some research on the interwebs, I have concluded that this code has to do with the MAF. Time permitting, I am going to clean the MAF sensor later tonight. In the meantime I reset the CEL, to see if it will come on again.
My only question, which I am unable to find an answer to, is:
Can there be a possibility that the P0101 and P0172 trouble codes be related to me replacing the spark plugs, or is this just a mere coincidence?
View 5 Replies
I am changing my own spark plugs for the first time. I have a spark plug wrench, dielectric grease, anti-seize compound etc.
I have a Haynes manual for my 2002 Toyota Corolla. The book was written before Irridium plugs were used. Should I tighten the spark plugs to the same torque specifications as regular plugs? The book says 158 inch pounds. How do I know I have tightened them to the right amount?
How do I avoid cross threading the spark plugs? What happens if you cross thread the spark plugs (assuming the car seems to be running fine)? Would I need a new engine or expensive repair when it is time to replace the spark plugs again?
View 19 Replies
I've got a 96 Toyota Camry, 4 cyl, that appears to be losing coolant. I do not see any apparent leaks. I've checked compression and all cylinders are 170lbs. Within the past year I've replaced the radiator and hoses, timing belt, water pump, etc. Within the past month I replaced the thermostat and radiator cap. I do see it bubbling in the overflow tank. Also you see vapor with the radiator cap off. I feel sure its probably a head gasket ..
View 2 Replies
I want to change the spark plugs and wires in my 1996 Ford Escort (1.9 Engine).
The problem is trying to remove the No. 1 spark plug boot and spark plug. Both are located behind the alternator and are difficult to get to. I tried a boot puller but could not get easy access to the boot to pull it off the spark plug. The other three boots and spark plugs are readily accessible.
Is it sufficient to place the dielectric compound just inside the opening of the boot before placing it back on the spark plug, or should it be placed on the metal clip that is ~2-3 inches down inside the boot?
View 2 Replies
I'm trying to turn the crankshaft by hand to verify my timing belt alignment, but meeting some resistance. is this because I have the spark plugs in? do i have to take them out to turn the crank? also, that little groove in the belt guide doesn't seem to line up with anything or get held by the rib on the crankshaft. does that matter, or have i got it installed wrong?
View 1 Replies
'03 Solara 4 cyl, 135K repl. Fuel pump, 45# press ok, NO scan tool code(s), turns over fine, no spark 2 plug. Started/ran fine before fuel pump change.
View 10 Replies
OK, well i have an old toyota pick up, One of the spark plugs ( the third cylinder) has some oily residue on it, indicating a problem with the piston. How bad could this be? Is it worth it to try and have fixed? I also am rebuilding my carb right now, so i am wondering if i is even worth continuing if the engine is messed up.
View 6 Replies
I have a 2008 Camry, 2.4L, and used the spark plugs change DIY sticky and it seemed to go painlessly. However, after the new spark plugs, the car seems to idle rough. It has 95k miles, and I did the following in the same tune-up:
1. Changed Oil
2. Replaced Air Filter
3. Changed Spark Plugs
4. Cleaned Battery Terminals
5. Cleaned MAF Sensor
6. Cleaned plugs connecting to ignition coils
I used OEM Toyota plugs, and even called the dealer to see if the gap needed to be set. And they affirmed me that the gap is preset on these plugs.
View 2 Replies
I have a 2006 Toyota camry v6 1mz-fe engine. My buddy changed the all 6 spark plugs using Toyota oem denso.
The car drive weird after that. When I am on the stop light, the car is shaking ( coming from the engine area ).
When I am driving 60 mph, it shakes .
View 14 Replies
Two of my plugs locking clips broke today on the wire harness side where the coil over plugs into the harness today while changing spark plugs. They will plug back up, but they won't lock together like they are suppose to. How critical is this? It is my wife's car will she break down? I drove the car maybe twelve miles, and everything seemed fine.
View 8 Replies
I recently replaced the spark plugs on my 2002 Camry SE V6 (Gen 5). Let me just say that it was INCREDIBLY DIFFICULT to reach the rear 3 plugs as they sit underneath the intake manifold, way to the rear of the engine compartment. To reach those, I had to unplug some wires reaching on top of the engine, then loosen the intake manifold.
Along the way I broke a tiny air valve that sits underneath intake manifold, and replaced it right away, before starting the car.
When everything was put back together, the car started wonderfully, only to notice the engine light come on. I had the codes checked at the dealer and they indicated a malfunctioning Catalytic Converter and A/F Sensor and some other emissions stuff. Later that day, the VCS/TRAC OFF light came on as well. The service guy at the dealer said those typically come on together with the Check Engine light, which sounds like something he pulled out of somewhere!
The car drives well, no hesitation, no weird behavior, but has no traction control, naturally. While loosening the manifold I had to use a little force to flex it out of place. My guess is that it I may have yanked something out place: may be a wire issue, or a sensor.
View 13 Replies
I have an 09 camry se 4cyl with 165k. I believe the service interval on the plugs is 100k. However, 75% of my miles are from highway driving. Plainly put, the car still drives like brand spankin new and get gets 30mpg hwy. This tells me the plugs are doing their job just fine. What concerns would you have if any?
View 14 Replies
I have a 97 Camry that looked like it had a small oil leak coming from the head gasket. It needed oil added every few days or so, so I changed the head gasket and now it overheats!
I changed the T-Stat, no luck. I took the radiator out and flushed it. It seemed to flow great too. I had the garden hose on full blast going in the top and it was coming out of the bottom just as fast with no back pressure out the top. So I think the radiator is good.
I'm pretty sure the fan was kicking on at the correct time but just to be sure I hard wired it so it's always on if the key is no, still over heating. Compression test shows 200, 209, 209, 211. That's pretty good right?
Just to be sure that the exhaust was not leaking through the new head gasket and heating up the coolant I did a liquid block test. Where you suck air out of the radiator cap and then it goes through a chemical which will change color if it contains exhaust gases. Not only did the liquid not change color, it was very hard to get any air out of the radiator, indicating that the system is tightly sealed correct?
The car is not loosing any coolant. I changed the coolant gauge sensor as well, still shows overheating.
Before I changed the sensor out I bought a thermometer and put it in the radiator. I was able to leave the cap off even after it started to get hot. The coolant did start to rise a little but I just bled it off from the drain plug at the bottom as it got higher, making sure to leave it full and not get any air. And the temp stayed below 200. This made me think that it was not overheating and thus the new sensor. This was not the case though. I realized that the coolant coming from the engine was very hot and then going into the radiator where it could cool down via my always running fan and then go past my thermometer.
The heater works great and even cool the engine down. This means that the heater core is not blocked and that the water pump works correct?
So after all of this I decided that there must be something blocking a coolant port. SOOO I took it all apart again only to find no blockages. I can see very well down into the block and fairly well through the cooling ports on the head and everything looks fine.
I also checked out the water pump and that looks great. Still in great shape and the bearing is not worn at all.
There was only ONE thing that was wrong on the engine (that I found) and that was the throttle body gasket. It was put on the wrong way so as not to fully block that air passage that I believe is pulled from the block into the throttle body. this could cause overheating?
View 12 Replies
I have a 1992 Toyota Camry. It had been burning gas, losing powere, white smoke smoking excessively through the tailpipe, and idling extremely rough, sometimes to the point of dying. It ran ok at highway speeds, but terrible everywhere else. We figured that it was getting moisture into the engine. We essentially did an upper engine overhaul, replacing gaskets and parts as necessary. It ran fine after this, and then three weeks later, started having the same symptoms. I found gas in the oil, changed oil, which turned it to run smoother, but still smoked and died at idle. I found out the clutch fan barely blows. I can't afford to get an actual mechanic involved, but I don't know where to look next.
View 5 Replies
I've been having frequent problems with my car.
Here's the information about it:
200,000 miliage
engine light is on when key is in ignition, but goes off when car starts up
Four cylinder engine
Here's the problem:
Car stalls intermittently
when it is about to stall, when i slow down, car putters a bit, and RPM gauge shakes wildly
when coming to a complete stop, car shuts off completely, and when trying to start back up, engine chokes.
Temporary solution:
I put the car in neutral and floor the gas pedal, then the car works again.
View 1 Replies
Motor seems to burn out spark plugs every month. I was using non volvo sparks. I took car to Volvo dealers and repairers who gave car a diagnostic check but nothing showed up. They told me to use Original Volvo Spark Plugs which I did. The Car went great with no problems for about 3 months thinking problem was fixed. Low and behold the same problem came back.
I changed spark plugs again (original Volvo) and car only ran for 10 ks and then ran very very rough with no power. Motor felt like it was running on a few cylinders. It seem this problem happens mostly in hot weather. Motor also heats up but when cooled down runs well again. I intend to buy new rotor Bosch and Distributer cap and if needed coil.
View 2 Replies
My 2004 honda accord will not start, there is no power to the spark plugs or to the coils.
View 3 Replies
I recently was given a 96 Toyota Celica 1.8L Auto 7AFE and I have been trying to troubleshoot some problems.
It started a year ago when my brother drove it to work and then after work it would not start back up. It sat for a while and now its mine. Problem is I was not getting any spark at all a while back when we tested it. I thought maybe the distributor. The other day it happened to just randomly start after a year of not starting. It made a small pop in the cylinder then boom ran just great until it warmed up and proceeded to shut down, would not restart. Checked the spark and it was very weak (yellow) and just seemed to be a slow spark, not firing as fast as I would think. Today I put a new distributor with a new cap and rotor in and boom she fires up immediately. Let it warm up fully shut it down, restarts fine, shut it down again and now it will not restart. Last time I tested fuel was fine, seems as if I am getting an intermittent spark and usually starts when it cools off.
Not sure what to do now, where to look. The wires seem ok with no corrosion but I have only worked on the 2.2L and I am lost!
View 4 Replies
I just replaced spark plugs and now it is running rough and reduced engine power light is on. did not mix up wires or coil packs. did one at a time.
View 13 Replies
I have a 1987 Ford Ranger 2.3L, it's the truck I learned to drive in (stick at 13yo) and the 1st car I crashed too... So now this baby is almost 30 years old and recently had a minor restoration...
Engine was pulled out and all gaskets were changed, spark plugs, wire... All that stuff... It has been running pretty good, however last week a water line broke on the Left side near the spark plugs (if you are looking at the truck)
Since then It has absolutely Zero power. The slightest hill and even when pedal to the floor will lose power. Yesterday went from the start of a hill at 60mph in 4th to 20mph in 2nd because it didn't have the guts to go 1/3 mile uphill... I checked everything I could, and my brother took it to the exhaust guy who made a small hole on the Catalytic Converter and said it was good, but he could tell it was running too rich...
I replaced some of the vacuum lines last night, I found a lose one on the fuel pressure regulator (I think that's what it is, Its towards the engine firewall on top).
Idles beautifully, drives great, no rough shifting, pinging or knocking, no misfires. So that's what has me stumped... Runs great but just no power... Also before water line broke it was running fine with power...
1987 Ford Ranger
2.3L FI
5sp manual, Rwd
View 11 Replies
