At idle (like at a stop sign or sitting in the drive way) my '92 Toyota revs up and dies down (kind of a "brrrrvvvvvv-buh... brrrrvvvvvvvv-buh") We have been fixing it up and got ahold of another Toyota that has a decent motor but the body, frame, and everything else is shot. We are pulling a starter out of it and was wondering if the part that causes the gallop could be replaced too.
View 4 RepliesI recently bought this cavalier about a week ago its and 88 automatic trans with 1.8 4 cylinder I thing not that it matters much. I noticed the exhaust had a smaller pipe from the manifold and the rest was strung with a bit bigger pipe and was attempted to crimp the pipes togather it was loud so I crimped thhe pipes better and used exhaust glue to patch the holes it runs better now to a point. but when I start the car it revs up a fair im guessing 3 grand since I have no rpm gauge but then it dies down to a low idle to the point were the car shakes a little bit.
with the exhaust fixed I can get it up to 20 kilometres an hour with my foot off the gas when I turn fully it wants to lurch ahead/backwards. when I took it out for a highway drive today I came to a stop sign so I slowed and stoped and the car stalled out. started no problem. but I also tried later putting it in neutral and it doesn't stall as I role to a stop it doesn't shake in neutral. I would like to have this fixed but I need some pointers as of were to look. im not sure if this means anything but when I got the car it had a bad enough radiator fluid leak at the hose meeting the heating car on the engine side of the fire wall I repaired that and no longer leaks.
I have an 87 ranger that has started having problems over the last week or so. I had a similar problem a year or so ago. I put a new fuel pressure regulator on and it fixed it. So it started acting up again so I got another regulator and it didn't work at all. It won't idle at all without dying. The motor revs up then cuts out completely and dies. It's like I'm repeatedly pressing the gas pedal when I do get it to idle but I'm not touching it at all. It runs fairly well on the road until I let off the gas then it goes to shaking and jumping up and down till I get back on the gas.
A guy told me to unplug a little cigarette pack shaped plastic box and see if it changed anything. I think he called it a map sensor? But that didn't do anything. I was thinking maybe the fuel filter was clogged up but I don't really know. It is fuel injected 2.9 4x4 regular cab. About 110000 miles. Not sure if filter has ever been changed. It doesn't smoke or smell like gas so I'm thinking it's starving for fuel.
I've got an issue with my 92 2.3 ranger.... sitting at idle for 30 or so seconds it starts to chug and sometimes dies.... I can hit the throttle and its fine for another 30 or so seconds.... while cruising on the freeway after about 30 minutes it starts to cut out badly... let out of throttle for a few seconds and it clears up and drives fine...
Here's the part that has me confused... pulled codes yesterday using a innova scan tool...
koeo were 4, 10, and 538...
koer were 111, 10, 157, 158, 181, 327, 328, and 334....
How does it give me a 111 pass code and then still come up with all the other codes? I am thinking my ecu may be screwed.....
I have a gorgeous, mint 4x4 1992 Toyota pickup...that runs terribly. Sometimes, it won't start. When it does start, it often idles very, very low. (Idler tension cable was adjusted up but it didn't work.) When I drive it, the idle goes up and down between very low and 4000 RPM. Sometimes, it stalls out all together, regardless of what I do to the clutch, brake, or acceleration. In an engine diagnosis, Knock Sensor came up, but there's a new one, and the cable harness is fully gone through. It's got a new engine with 67,000 miles on it, a new fuel pump, and just about every part has been replaced. It's been to about 10 mechanics, all of whom can't figure it out.
View 11 RepliesIt's a 1992 Celica, GTS 2.2L for reference.
After driving down the highway I noticed my temp fluctuated from half way to full and bounced around until I arrived at the closest Canadian Tire/Station. I looked under the hood and noticed the stain on the coolant container wasn't the actual level of coolant. I then topped off the coolant and parked the car for about a week. When I tried to start her up, I was faced with a weak and poor idle. Almost as if the car is struggling to run. I have had times in the recent years in the summer months were I felt I had to pump the pedal on really hot days to kickstart her so she would run. Was this a warning sign? Other than this problem I face, the car runs smooth. I did a good tune up 2 years back, replacing the ignition coil, plugs, etc..
The idle goes from 0 - 500RPM in neutral and when I apply gas it struggles to gain power. The car is parked, I don't dare to take her around the block. It stutters and seems like she is struggling to get fuel. I say that because, when the key is turned to the on position I do not hear the fuel pump underneath the back seat activate. I did try jumping the terminals, something like B+ and FP.... The pump turned on and I heard fuel but when I started the car, I still had the same problem. I would need to pump gas or she would stall out. I do not know where the fuel line is to try and check the pressure or even where the relay is located.
Could it be the Fuel Pump?
Could it be the Fuel Pump Relay?
Something Else?
My guess is the Fuel Pump, but if you could take a few mins and replay that would be great. I have had my Celica for about 7 years and I would like to keep her going!
I just bought a 92 Toyota Celica for something to play around with. It's got just over 200,000 miles and everything seems to run alright except there is a really rough vibration at idle. The vibration is so bad that it's almost visible. You can still feel the vibration in drive but it isn't nearly as bad.
Any clue at what could be causing the vibration? I'll try to get a sound clip or video uploaded ....
Alright so I got a 92 toyota Celica 2.2 5SFE recently and guy before did a head gasket.. well i started to work on the car. fix things here and there. well one issue I cam across was low compression.. 170 170 30 90.. so i was like ok the guy didnt do it right.. took it apart. found out valves were stuck open. So i ordered a remmaned cylinder head to put in and new head gasket set etc.. replaced all gaskets that came with it..
Also put in remanned fuel injectors due to one leaking so i just replaced em all. New plugs, wires, cap, rotor, timing belt, followed the oem manual word for word to install and remove and timing is right. But I got it all back together and ran great. until my tps went out(replacing that soon). Compression is now 180 across the board.
Now I got a knocking issue, Its quite apparent at idle/ low rpm.. solid sound, goes away at higher rpms, gets plenty of oil to cylinder head, started bout 150 miles after finishing. Im not sure where to start.
Since having my engine replaced with a newer used engine block my idle speed when I first start it up or when it is cold is around 2000rpm which lasts for about 2-3 minutes until it begins to fall to the normal range of 1200-1400 and finally to 850 or 900rpm when warm. how can I fix this or is it okay to idle at 2000rpm for a couple of minutes? is it hurting anything?
View 3 RepliesI drive a 2004 Toyota Matrix SRX, It has a 6 speed manual gearbox. Sometimes when I am driving and i push the clutch whether to decelerate or when I'm sitting at a stop light the car dies. It seems like when the engine is slowing down it sometimes doesn't catch itself to idle and just dies.
View 8 RepliesI replaced my engine that had 155,000 miles with a newer used one with about 30,000 miles. since the swap my gas mileage is down by one third or more. Everything else seems fine except that my cold start idle is up to 2000rpm's until it drops to normal within 3 minutes.
View 2 RepliesThis is my first experience with auto tranny trouble so I'm a bit out of my depth. It started a few days ago. When you put it in gear and step on the gas, the engine revs, but no forward movement. If you keep giving it gas and rev it up, it will eventually grab and off you go. This happened around town after I took it to work last week when I went out for lunch.
When I drove it home, it slipped in and out several times in town, then by the time I got out of town (maybe 5 minutes driving) it evened out and didn't slip the rest of the way home (a 45 min drive). My assumption is that once it warmed up a bit that stopped the slipping. I checked the transmission fluid when I got back from lunch, and it was a little high. I drove it again today a week later and same thing only I didn't drive it long enough for it to warm up and stop slipping like it did the other day.
Other details: The truck is a 4x4, extended cab, v6 Ford Ranger with about 175k miles on it. I've had it about 1 1/2 years and its performed great up till now.
Got 99 Grand with a issue. It'll run fine then you come to a stop light and it'll die. try to start it and it'll rev to 2000 rpm then drop to almost nothing then rev again then die. It may do this once or 2-3 times. If you keep your foot on brake and give it gas you can keep it running put it still revs. Once at highway speeds it runs normal. When you get home or wherever and shut it off for awhile it'll start and run normal. Had it in shop twice. No codes. Replaced pvc valve and hose, fuel filter. They said start replacing stuff till it stops. I don't go there anymore. Another shop said unless it does it for them they wouldn't know where to start. Of coarse every time it does it, by the time I get it to shop it runs fine. I can do brakes, axle shafts, bearings but electronic fuel injection stuff still baffles me.
View 4 RepliesI have a 1998 gmc sierra 2500 truck when i start it it runs just fine but after i have driven it awhile when i go to stop as soon as i come to a stop the engine revs up and down and it dies it will not do it if i am in neutral or the engine is cold, what could be causing that....
View 7 RepliesI just picked up my new 2014 Chevrolet Camaro with the V6 and 6 speed manual transmission. If I just punch the gas pedal when in neutral, the engine almost dies for just a second but then rev's up normally. It seems like a burst of gas chocks out the engine. I have tried the same thing in other Camaro's and the engine rev's up normally as soon as you punch the gas pedal.
View 13 RepliesI have a 2005 Camry and it was stalling while driving occasionally. It had gotten worse, so I cleaned the throttle body as was suggested. Now, when I try to start it, the engine revs really high then goes back down and dies. This is without putting any pressure on the accelerator. What to do next?
View 1 RepliesCar basics: 1992 Chevrolet S104 cylinder2.5 L
Have in the last 4 months replaced :
(1)fuel filter
(2)fuel pump and spark plugs
(3)EGR Valve
(4) Vacuum lines (possible vacuum leak)
Problem: Car will turn off while driving, sometimes after a service engine light comes on. Usually at 40-65 mph, car will shut off with electricity still working. When I attempt to start the car afterward it will turn over, but will not catch. Have had to be towed twice, other times, we waiting we it out, came back later and it started up just fine.
Attempts to solve: Various points I've brought it into a AAA shop, and they were unable to figure it out without the check engine light on (pre-1996). I finally did get the codes read, and they were for the EGR Valve, and the MAP sensor. EGR replaced, test on MAP sensor showed no problems afterwards. codes were cleared.
Yesterday: Last night the car turned off randomly on me again, and had to get towed home, today it took a few tries, but then the car started up just fine. Took it to the shop, they reattached a loose wire from the spark plugs, and are asking me to replace the (1)wiring, (2) coils, and (3) rotor head but without the check engine light on this morning, they are not 100% sure where the problem exists. The car sometimes runs fine, but since I am going to be working pretty far from home, I need reliable transportation. Everything else is in great shape on my little pickup, but this has been racking my head for a bit.
So I have a 95 Legacy sedan, FWD. It's been a kind of problematic car, and the engine was replaced about 5 years ago (I assume with an old unit, but I'm not sure though because though I was in the family I wasn't driving it then). But, it's held up and has continued to be at least roadworthy. But recently, it's developed an issue where the engine will just randomly die while I'm on the road. All/most of the dash indicator lights come on, but if I shift it into neutral and turn the key, it'll come right back up. Occasionally it'll die again almost immediately, but usually it'll be fine for at least a while. And anecdotally, It seems to happen more frequently at lower revs such as idling at a red light (though will occasionally happen while I'm moving), and when the engine is cold - generally once I've driven around for a while, it's not a problem anymore.
View 3 RepliesI am repairing a 1992 Celica GT w/2.2 litre I4. Just replaced the TPS. Now, it will only idle. Any caressing of the accelerator, and the engine dies. Will idle smooth as glass for abt 5-10 minutes, then begin idling rough, and then die. Will not allow me to restart immediately after it dies. Must wait 10-15 minutes before restarting. When the vehicle is placed in gear, it will continue to run, but the moment the accel. is pressed, the engine dies.
I think part of it may be vacuum-related.
1992 Escort GT 1.8 liter ... It's been a problem for a while, where I'll just be driving (or at a stoplight) and the engine dies. It doesn't sputter or give any signs (that I know of) before it goes. Usually if I let it sit for a while, generally under an hour, it'll start right up again and run for a few days and then happen again. The engine light will sometimes come on, but only after I get it started up again, and it never stays on for long. The other day, it died on my way to work and didn't start up again for a few days, but the engine light was on, and gave a code 23. I think this means I should get the throttle sensor fixed.
View 1 RepliesI have just inherited my recently deceased father's 1992 Ranger with the 2.3 liter engine. He was a Ford Mechanic but got to ill to worry about fixing the Ranger. So, let me begin, the engine dies randomly, (at idle or in gear driving doesn't matter what gear or speed), turning key to off and then to on will allow vehicle to restart every time. No "Check Engine" light has ever lit, I do have an "Antilock" light that comes and goes. The engine codes I keep getting are: 10, 218 and 222.
Code 10 is a computer check code,
Code 218 is "Loss of Ignition Diagnostic Monitor (IDM) signal/left side, and
Code 222 is "Distributorless Ignition System - Loss of right side ignition diagnostic monitor (IDM) signal.
These codes were from my Innova reader. I have read where other similar problems were fixed with a new Crankshaft Position Sensor, replaced mine, no change. Another symptom I just noticed is my temp gauge stays near the cool end when it should be higher.