I have a 79 toyota pick up, that will not run. the engine turns but does not start. It has spark, though not the best should start. The carb is old but there is gas in the engine when i try to start. compression in all the cylinders is fine. A friend thinks maybe the timing chain jumped a tooth. I cant find the bright link on it so im having trouble knowing if that is the problem. What it could be?
View 5 RepliesI've got my sister's 1995 Dodge Neon with the 2.0L SOHC. While driving it recently I heard a horrible squeaking noise then a ZZZZZZzzzzzz sound. I immediately pulled over. The check engine light came on, and I shut the car off. Coolant was all over the place leading me to believe the water pump failed. I had it towed to my house, and now I will have it towed to the shop to get fixed. I would like to have them repair the timing belt and water pump. However, I am afraid that the valves were beaten to a pulp and now I will need a new engine. I was only going 35 mph when it happened. What are the odds that my valves were smashed up, and is there anything I can do to check them before I pay for a timing belt/water pump repair?
View 19 RepliesI brought my 2004 VW Touareg V6(83k miles) to the dealer for a recall on the ignition call and much to my surprise, was presented with a diagnosis of a $6,000 problem! The dealer told me that the computer read some codes which say that the timing chain is stretched and needs to be replaced. They said it will take 4-5 days and should be done asap so it doesn't "go out", because if it does, it's an even more expensive problem. I took the car to another VW repair shop and they asked me if I heard any noised when I start it cold (like pebbles in a bucket). I have not had any problems like that at all, so they said I shouldn't worry until I start getting symptoms. They also said there is no recommended point (like 90,000 miles) when VW recommends the change, so it really shouldn't be a common problem. I want to do the right thing, but I don't want to rush into an expensive repair if it isn't necessary.
View 1 RepliesOK, well i have an old toyota pick up, One of the spark plugs ( the third cylinder) has some oily residue on it, indicating a problem with the piston. How bad could this be? Is it worth it to try and have fixed? I also am rebuilding my carb right now, so i am wondering if i is even worth continuing if the engine is messed up.
View 6 RepliesThe timing belt broke on my aveo, destroying the engine. I replaced the engine with a used one. Now I get the car back on the road and the automatic transmission won't shift from 3rd gear into 4th. Is it possible this problem was caused when the new engine was installed, or the transmission was damaged when the timing belt broke?
View 4 RepliesI drive my pickup (87 Toyota 4-cylinder carburetor 5-speed Xtracab Deluxe) occasionally. When it's sat for a week or more it takes a few tens of seconds to start. I bought a booster battery. The charging light comes on, but it goes out as soon as the engine starts. I'm used to hard-to-start cars charging for a while after a long start. The voltage coming out of the alternator is okay. The battery is new; the density of the electrolyte is right.
View 19 RepliesWhen I turned the key to start my car, I got zero activity from it. No ticking, no lights, nothing. So I tried to do a push start, and the engine wouldn't engage. I took the key out, and suddenly my dome light popped on (though it was dim). I put my key back in and turned it, and dash lights looked normal and at full power, but as soon as I pressed the clutch down and tried to turn the key, everything went dead. I took the key out, put it back in, and turned it, but got nothing.
I pushed my truck up to the top of an incline, and turned the key. All the lights looked normal, so I thought I may be able to push start it. Key was in proper position, clutch was engaged, and gear shift was sitting in first. I got a decent speed, released the clutch... and everything went dead.
I can't decide if it's my starter or my ignition system, though I suppose it could be the wiring, or even something else.
My 94 truck (Toyota 6 cylinder 3VZ engine) is currently idling at ~2000 when I first start the engine. After warming up or driving for a substantial amount of time, this eventually drops to ~1000-1100. I had the throttle body removed and cleaned (twice). This stopped some up-and-down revving which was happening, but not the high idling. This is a relatively recent development, and I've gone to 3 mechanics AND the dealer, all of whom say, 'it's fine'. They say it should run 'a little higher when it's cold'.
I think some of these assessments were based on the simple lack of engine error messages (no codes from the computer = no problem). I admit that I'm no expert, but I've had the truck for a decade; I know what's 'fine' and what's not. The usual idle was ~800 (in agreement with specs) and I've driven this truck in temps down to -30F. It has never idled this high before. Since it gets close to normal RPMs after warming up, I don't want to turn the idle adjustment down. I moved from a very cold, very dry climate at 6000 ft to a very wet, moderately cold climate at sea level - is there some other adjustment I need to make? Or is it normal for this engine to run so differently in these two climates? I'm at the end of my rope since no one thinks it's a problem except me.
I have a 1979 Ford Thunderbird with a V8 5.0 liter engine. Here's the mysterious problem... the engine turns over when I turn the key but stalls when the key is released. Thinking that the alternator died, I replaced it with a new re-manufactured unit and the car's symptoms stayed the same. Also checked the fuses and the fuel filter and found that plenty of fuel is getting to the carburetor. This issue with the car not starting appeared literally overnight after I attempted to install a new radio. Prior to this the car ran reasonably well – always started easily and ran without a problem. Wondering if there is a possibility that I fried some part of the electrical system when I fussed around with all the wiring under the dash. Someone else had attempted the radio installation previously so the wiring there was already a mess of cuts and re-connections and was hard to sort out.
View 7 RepliesMy 1995 Toyota Camry will not start, the engine turns but does not engage. I have had the fuel pump, fuel filter, and a relay switch replaced. After each repair the car runs for twp weeks and then will not start. I have had it towed and the mechanics start the car with no problem and they are unable to diagnose the problem. In a month and a half, I have had the car towed 3 times.
View 4 RepliesI have a 2003 Toyota Tacoma pickup. I bought it used in the spring of 2009. I drove it for a few months without any problems and one day this problem developed. It won't start on the first attempt. Or it will start and then immediately die. It will take two or three tries to get it running.
I took it in to my mechanic and he couldn't find anything wrong. I got a tune-up anyway and it drove like a champ. Until the next day when the problem came back. This persisted for a few weeks more and then went away.
This last summer it started happening again and continued up through October and went away again. I think the problem seems to happen when it's hot in the summer.
The engine turns and air blows out of the throttle body. My fuel pump and TPS is good. What else could it be?
View 6 RepliesI just got my timing belt replaced by my mobile mechanic thats been doing it for years. I saw him do the work and get the timing right. When he was done the car turned on and ran perfect. After about a minute the car just shuts off. Now the car won't start at all. The car turns over but no start. The car ran perfectly before I had this job done.
View 9 RepliesThe timing belts keep slipping on my car. I replaced the belts but it keeps happening. I went to readjust the belts today and noticed the pulley looks off. I know it needs to be replaced but given that it's the bott one under the radiator hose I'm not sure if it's one that I can easily do myself or if it would be better to have a mechanic do it.
147213874510541690085.jpg
1040x1857 841 KB
I have a 2007 Gen II with 133,000 miles and am using Amsoil synthetic oil and an extended life filter, changing oil every 10,000 miles. What is the frequency for changing belts, hoses, and timing belt? Other than a faulty latch on the rear lid, I have experienced ZERO problems with the car and would like to keep it so.
View 6 RepliesI have a 2000 Dodge Caravan SE 3.3L. The timing chain recently broke. So I replaced the timing set, cover, water pump, camshaft sensor, and oil pan. The timing is all aligned. It starts right up, but then stalls. Unplugged the front three spark plugs to see if one of those were the problem, and then it ran better and didn't stall out.
View 3 RepliesI drive a 2005 toyota mini-van. Lately the engine has started sounding strange. it has been sounding like a tiny diesel engine or like a go-kart. There are no lights on on the dash, I have not noticed any changes in fuel consumption, acceleration etc. and the temperature is normal. Is this a timing issue? is my car about to die? what are the repair costs?
View 5 RepliesI have a 2001 jag stype v8 with 180k miles. I bought the timing kit and aligned the camshafts correctly but it still idling rough and sounding like a diesel truck. What still maybe the problem?
View 19 RepliesSo I had oil leaking out of my starter so I ended up pulling it and replacing a gasket behind the flywheel... Now the car didn't run because the timing was off by a lot so I jumped a few teeth on the timing chain. Now I have a bunch of white smoke and the car lacks power. It will stall going reverse out of my driveway unless I rev it high. The engine itself has less then 5k miles on it as it's rebuild so I don't think it's a head gasket if it was running fine before I pulled the flywheel off. The idle sounds fine and feels smooth but puffs white smoke. I used a timing gun and adjusted it, and seems on point but now I'm stumped. What could it be? 1972 Honda n600...
View 19 RepliesI have a 2005 Chrysler Sebring. In December the timing belt failed while I was driving down the road. I had the dealership I purchased the car from replace the timing belt as well as the water pump while they were at it. Ever since I have had and issue with it vibrating at idle. At first it was making a whining noise as well. I took it back and they told me that they had installed the belt too tight. Afterwards I still had an idle issue although the vibration was a little different. I also could distinctly hear the belt hitting the casing a few times.
I took it back again and they stated that the belt had been put on too loose. So now they have adjusted the belt again and it I am no longer having the whining or belt hitting the casing. But I still have an idle issue. It has changed again and is kind of a pulsing vibration. I can feel it in the brake pedal when I am at stops. I seem to hear the pulsing while driving as well but this may be from my new tires as well.
During this whole readjustment process they have not mentioned actually checking the timing. Just the belt tension itself. When I first reported the idle issue after they put the timing belt and water pump on they told me that it could not be related to timing and that it had to be an ignition issue. But I asked a work associate who used to work as a mechanic and he stated that it would be a timing issue.
I am going to contact the dealership and ask them to check the timing belt again. I never had this idle issue before the new timing belt.
So I have multiple issues that all seem to stem from a power steering leak. According to the dealership, the PS pump is leaking fluid onto the serpentine and timing belts causing them to swell. This in turn has something to do with the AC compressor not working but they wouldn't give me details. When I looked at the clutch wheels on the AC compressor, there seems to be a good amount of rust in between the two wheels. I can't say that I trust the dealership because the original owner was bought out by a larger group that is known to just say "replace everything". I usually do most of my own work on my 95 Tacoma, so I'm no stranger to import v6 motors.
View 4 Replies