Subaru - Forester :: 1999 - Getting Error Code P0325 Now Running On Two Cylinders?
Jun 22, 2013
I took my car to my previous shop for a P0325, Knock Sensor Circuit Malfunction. They wanted nearly $500 to fix it. My new shop said that I just needed some engine treatment and the code went away for a week and a half, but it came back yesterday, and my engine ran a little rough.
I heard what sounded like a very rough engine and it was my car. The technician came in saying that I was only running on two cylinders, but that sounds like far worse of a problem than I had been experiencing. They say that I need a $266.80 valve adjustment, which is all labor, but the total is $300 more than that:
Engine Light diagnostic: $44.99 Shop Fee: 35.00 Tune up package Remove and replace spark plugs: 60.03 Additional access time - remove: 64.20 and replace spark plugs: NGK Spark Plugx4: 9.96 Adjust Valve Clearance: 266.80 Pepguard Limited Extended Labor: 58.65 Warranty BWD Custom fit ignition set: 36.39
Parts: 46.35 Labor: 436.02 Other: 93.65 Tax: 6.55 Total: 582.57
Of course, my roommate, who is upset that I am not continually pouring fluids into leaky power steering and AC systems butted in and said the entire thing is preposterous. Problems with cylinder firing are invariably the result of bad spark plugs andor wires.
Well, they say that I need to replace those, which cost $46.35, the least expensive entry in the entire estimate. They just want to charge $124.23 to replace them.
Why don't I replace them myself and see if that fixes my problems?
They say that if the valve clearance adjustment does not fix the problem then I need new cylinders and valves.
Regretfully, I have a "service plan:""Engine: All internally lubricated parts contained within the engine block, cylinder head(s) or rotary engine housing(s); oil pump; timing belt or chain, timing gears and timing tensioners; water pump; engine block, cylinder barrels, engine head(s), rotor housing(s) if damaged by the failure of an internally lubricated part. Dipstick and tube; harmonic balancer; oil pan; timing chain cover."
I cannot imagine that it would cover a valve clearance adjustment and they would only cover cylinders and valves "if damaged by the failure of an internally lubricated part."
So, ride my bike eight miles tomorrow, replace the spark plugs and wires, and hope that it is enough?
View 19 Replies
Advertisement
I am getting error code po457 Evaporative emissions error, I am told the canister purge valve could be bad.
View 4 Replies
Got a 98 Subaru Forester with 130,000mi. Good car so far. Just got a good deal on a scanner and it reports 1 code - PO0400. I see it mean EGR flow error. What is the most probable cause or a troubleshoot process to narrow it down? My repair manuals on the car are kind of lacking and I can't even find the blasted EGR valve! I thought I found it but I think it's the knock sensor.
View 14 Replies
I have an '04 Subaru Forester which sputters and stalls after fill up. It sends error codes for cylinders 1, 3, & 4 misfiring...I only have a 4 cylinder car - This only started Friday - a few days later and I'm really getting desperate. I screw my gas cap on, we check the connections...and we've read all kinds of random solutions that spread across the board.
View 18 Replies
Recently, my car had started having cooling issues. It was running hot, into the danger zone, and it would not blow hot air. I took action and replaced the thermostat myself, drained the coolant, and bled out any air bubbles, filled it up with coolant and the problems still persisted.
View 14 Replies
So i got a 98 passat sedan used and was told it read a p0411 code. The person at autozone told him it was a cam sensor. The sensor was replaced. I know now from the manual that codes reads for sec. Air injection system , incorrect flow. It could be the vacuum lines. Now lets say it is the vacuum lines. Their is a misfire on cylinders 1-3.
View 4 Replies
will it hurt my 98' forester to drive it when one cylinder has no compression? They tell me it needs a valve job for 2,500. They already put a mass air flow sensor in, and replaced plugs and wires. Still got the miss, but I need the vehicle.
View 2 Replies
I have a 2003 Subaru Forester, bought it this past January. Got 163,000 miles on it, and we've driven it mostly around town. Over the last month, it has developed an intermittent problem with stalling and rough "putt-putt" running, and will only keep running if the gas pedal gets pumped. This seems to happen about every other time we turn it on, but without a pattern. It can be running fine, and then switch mode, as it were, to running rough and tending to stall. I've gotten ignition codes (check engine light came on and I had my guy check it out on the computer) twice. My mechanic (a long-term Subaru mechanic) has checked out the injectors, and replaced the head gasket, but the problem has not changed. I'm thinking that this may be an electronics issue or possibly something in the gas tank/line.
View 1 Replies
1998 Forester, 233,000 miles.. Two years ago it started running hot after 15 minutes of either driving or idling. Coolant seemed to vanish into thin air. The Subaru Dealership said that I either had a bad head gasket or a cracked cylinder wall. They said if the head gasket was bad then need to replace the head gaskets. They said if the cylinder wall was cracked, then we would need a new engine.
View 4 Replies
I have an 06 subaru forester with a little over 130k miles on it. The AC has now become intermittent and when running doesn't blow super cold air. I had it recharged but that didn't fix the problem. What happens is that it will run fine for like 15-20 minutes or if not hot. The clutch will start by attaching very firmly but then suddenly for no reason will disengage. It is not slipping the belt at all. I dont think that it is a matter of too much air gap because when it grabs it does so very firmly. Also when they were charging it i noticed that the for a moment it was kicking on and off rapidly and then he did something that looked as though he might have released some and it stayed more constant?
View 1 Replies
I am getting P0355 error code and potential misfire codes on all cylinders. Engine light and VSC stays on now. Idle is unstable and power is a little jerky at times. I bought a Denso direct ignition coil to replace, however, Cyl 5 looks difficult to access.
View 3 Replies
I purchased a 2001 Subaru Forester about 4 years ago. Within 48 hours of buying it from a dealer, the check engine light came on showing the PO420 code. The car was running fine without any problems and it was suggested to us by 2 independent mechanics that Subaru is notorious for throwing this code, so we didn't investigate it any farther besides doing a fuel system clean/flush that was offered to us by the dealer.
Lately, the car has started sort of shuddering during acceleration so we figure it's time to look into this more, but just trying to figure out where to start. From what I understand, this model has 2 catalytic converters and 2-3 O2 sensors. I've been reading as much as I can on the topic and watching videos trying to figure out our options and whether we should try replacing the O2 sensors first or just go for replacing the whole shebang. I know we cannot afford the pricey repair of it all right now so the car will have to sit for quite some time before we can do that; however, if we can figure out how to do it ourselves, we could get it done much sooner.
My questions are:What is the likelihood that this could still be an O2 sensor issue considering the shuddering when accelerating?
What other signs do I look for besides rattling in the cats to know they might be bad?
View 9 Replies
I have a 2002 Subaru Forester L with 178,000 miles on it. I just had the valves adjusted. I have replaced the coil pack, #2 injector, plugs, wires, and throttle position sensor. I have also cleaned the idle air controller. The car only shows sign of a miss when it idles. It gets great gas mileage otherwise. I am at a loss on what to do next as the car doesn't have a MAF sensor, I can't do anything with it.
View 19 Replies
The check engine light on my 2006 Subaru Forester with 92,000 miles came on recently. A scan revealed the engine was running lean. After three more trips the mechanic determined the rear O2 sensor was bad and replaced it. This was the only part replaced. Now the computer is sending code P2097; Post Catalyst Fuel Trim System Too Rich Bank 1. I have read it could be anything from the catalytic converter needs replacing to "resetting the adaptation values."
View 2 Replies
I have a 2006 Subaru Forester with 95,000 miles on it. Earlier today the CEL (solid) and cruise (flashing) came on while I was driving. I believe it may have occurred as I was accelerating up hill. I filled up yesterday, so I tightened the gas cap when I stopped. On my way home, I stopped by my mechanic and they read the code; P0420 Catalyst Efficiency Below Threshold Bank was the code that was read. They reset the code for me but told me that the catalytic converter is what needs to be replaced.
My question: Could the light coming on be incidental (i.e., is it possible that it was a "blip" and my catalytic converter is okay?)? My mechanic said he thinks it is, and that my car should last me quite a bit longer. I am asking because I've put in a bit of money into the car of late and I'm wondering if I should just jump ship. I should say that the majority of the repairs are maintenance (e.g., brakes, tires).
View 8 Replies
My 2000 Forester has 96,000 miles on it. A few months ago, the CEL came on. At first it would turn off every couple of days but would eventually pop back on. I first thought it was tied to putting gas in the car, now I think it was just a coincidence.
Over the past two months, I have replaced the catalytic converter with a aftermarket piece (done by a mom and pop muffler shop) and replaced the front o2 sensor three times. The first two times, I used Bosch sensors from an auto parts store and had the code cleared. After about 50 miles the CEL came back on. Just yesterday, I picked my car up from the dealership where they installed a Subaru fron o2. After about 30 miles, the light is back on again. Code is P0133 - heated oxygen sensor, bank 1 sensor 1, circuit slow response.
Now, the dealership is suggesting I need to replace the catalytic converter with a Subaru converter before they can source the issue.
View 19 Replies
At a bit over 43K miles the check engine light came on with a blinking cruise light. Dealer has confirmed that both secondary injection pumps have failed for reasons unknown. I think this is part of the pollution control system.
View 3 Replies
2002 Subaru Forester I took my car to the Auto Zone to read a check engine code. It came back as being a "knock sensor". Besides that I needed a battery, and when the guy was putting it in he said my engine was moving too much and that I probably needed motor mounts.
I was looking at a discussion back in 2010 and the Subaru specialist told the person needing motor mounts is rare for a Subaru, is that true? I'm taking it to a mechanic, what should I expect? how many motor mounts does a subaru have?
View 7 Replies
What is the possible, or most likely, cause of a Knock Sensor No 1 Circuit Malfunction reading??
View 1 Replies
The head gaskets are less than 2 years old, radiator only almost 3 years old, I've constantly had oil leak issue. Now the problem is my temperature gauge rises after driving for 20-30 minutes when I'm going at a lower speed or in stop and go traffic. Both fans are working, no leaks, new thermostat, and new radiator cap.
View 2 Replies
My Keyless remote control is "DEAD" however my system is somehow engaged. In order to start my 99 Subaru Forester I need to reach under my dashand hold in the emergency override button. Car starts fine every time. Is it difficult to unwire this keyless system? I'm not going to keep this car much longer. Will probably replace car before end of 2013. Easy fix or keep driving as is? Any possible problems if I keep starting car with button release?
View 2 Replies
