Stalling - Electrical-wiring - Hyundai - Sonata :: Stalled Suddenly When Idling
Jan 26, 2012
Weeks ago, I was waiting for someone with my car idling and suddenly it just stalled. The battery power was still on but the engine died. When I restart it, it starts up but then dies after a few seconds. After trying 3-4 times it no longer starts. I had it towed to the repair shop and by the time they went to look at it, it started up just fine. A few days later I was driving (like 1 min from my house) and the car engine died, again the battery was still working. Power steering was gone. I coasted off the road and tried to start it--again it would start up and then die and then after a few tries it no longer starts. I had it brought to the repair shop. Again, it started fine for them but they changed out the battery just to see. I also had fuel cleaner put in the gas tank.
Just to be safe, I brought it to a dealer since my normal mechanic couldn't find anything. At the dealership they ran codes and didn't find any. They said that sometime the lines to the cams or crank get corroded but that mine looked fine. Since it wasn't doing it for them, they didn't have any other recommendations. Everything has been fine for the last few weeks and then I went to start my car last night. It started fine even though it's really cold and hasn't been driven in a few days. While I was scraping the car, I could hear the engine turn off. When I re-started it the same pattern happened--restarted the first few times and then died and then wouldn't even start. I don't even know what to do at this point since it only seems to happen close or at home and not for repair places.
View 3 Replies
Advertisement
When I started the car the check engine light came on. Since there had been a lot of rain recently, I thought that perhaps it was an electrical malfunction since the performance of the car did not seem to be affected. I was only a few miles from home and going at a constant speed on the highway. When I slowed down to get off at my exit I noticed that the car wasn't getting up to gear with the same power as it had been. By the time I had to slow down for five or six stop signs, the car was having a lot of trouble getting up to speed, and at the stop sign before my drive way, it stalled and wouldn't start (although it always sounds like it's just about to turn over). The mechanic is suggesting an engine flush and tune up, but both seem a little excessive, especially the engine flush.
2005 Hyundai Sonata (manual transmission)....
View 11 Replies
I have an 01' f150 that everything is going out on. I've replaced the GEM module thinking that's what it was to no avail. First thing to go was all four windows which have currently been stuck halfway down for 2 weeks. It's stalling out during idle like it isn't getting enough fuel to it. Brake and engine light on dash are staying on. Radio, interior lights won't come on. Will not come out of park once in. I have to do the old forward, back, middle key trick to get it out of park into neutral so I can start it and go. I've also checked all fuses and relays under dash and under Hood.
View 3 Replies
On my daily commute in stop-and-go traffic, on a bridge, headed downhill, suddenly neither the accelerator nor the brake pedal would engage in my 2008 Elantra. Cars in front of me had sped up, then ground to a halt, and I was coasting downhill toward them, at a pace too fast for the handbrake to stop me. I couldn't downshift either (the car has automatic transmission, but shifting to low lets the engine slow you down). With nothing else to try, I shut off the ignition and then turned it on and, amazingly, all was back to normal. The dealer didn't find any trouble codes in the computer so they say the car must be OK to drive. But I don't feel safe driving the car. This might have happened and what I can do to fix it?
View 16 Replies
I just bought an 07 Hyundai Entourage (Kia Sedona clone) a little over a month ago. We had our first storm last week and my wife tried to use the washer fluid on the rear and it didn't work (it was below freezing). I looked at it and the front didn't work either (no noise from pump motor either). So I found out it has a pump for the front and one for the rear but they are on the same fuse. Checked the fuse and it was blown.
I thought maybe it was due to the fluid in the car freezing (no anti freeze fluid probably). Put the new fuse in, tried the front for about 5 seconds and it worked. Tried the rear for 5, it worked. Tried the front again, nothing. Tried the rear again nothing. Pulled the fuse again accept it wasn't blown. Put a couple of different fuses in. Nothing. I did this while it was above freezing...? could both pumps have burnt up at the same time? Is there any other fusible link between the motor and switch?
View 4 Replies
My Honda has a strange problem that is vexing my mechanic. While I am driving, the engine spits and sputters and sometimes dies. I try to restart and it starts right up but runs rough. Sometimes it takes a while to start back up. If I wait a few minutes, it will start again and drive fine for a while. Then it will do it again. After it is warm or when it is cold at the start, it won't do it.My mechanic cannot get it to do it long enough to diagnose. The computer is not throwing any codes. I believe it is electrical because when it does this, the speedometer goes crazy bouncing up and down. Electrical problem also may explain why the computer is not throwing any codes. I need to narrow it down because my mechanic is reluctant to start trying things as I don't have a lot of money to throw at this.
View 4 Replies
Yet again my honda is doing some new. My mid dash lights don't come on at all anymore (even when i start the car), my power drive and winter drive buttons don't work, I can't stop/start on a hill, I have to get 2rpms going to get anywhere, and my battery volts are over 12 when driving.
View 1 Replies
1997 Ford Expedition 4x4
When I push the switch for the drivers window I can hear the relay in the fuse block make a click but window doesn't move. If I push the switch for any other window (on the drivers door or any other door) no click at the relay and no window movement. I've swapped the relay with other relays in the fuse block but nothing changed.
I've tested the driver side window motor by running 12 volts directly and the motor works fine. When I press the PDL switch I hear a buzzing sound coming from the passenger floor area behind the glove box but the locks do not go up or down. I started the truck and when I put it in gear I can hear the PW relay in the fuse block clicking repeatedly. Put the truck in Park & the clicking stops.
I was told (on another forum) that the problem is most likely my GEM module. Bought a used 1 on eBay and installed it today but nothing changed.
View 7 Replies
I have a 1996 F250 460CI that was running great for years and all of a sudden it shut off for a few seconds when I was on the expressway. It was like turning the ignition key off and turning it back on. It did it several times and eventually just died and would not start. I put a new coil on and it worked fine for about 150 miles and now it started doing the same thing again. The check engine light was on for a few seconds but not all the time so I am not sure if diagnostic equipment will show any error messages. Mileage on my truck is 92k. Does this sound like a distributor pickup issue?
View 6 Replies
I installed LED tail lights a few months ago, now all of a sudden the passenger side does not light for brakes or turn signals. The lights came with resistors that I put in when installing and the adhesive wore out and they were dangling in the truck frame. The wires connecting the resistors to the light were damaged. I taped the exposed wires and secured them a with a heavier tape, but taping did not work. I also tried switching the resistor packs with the driver side to see if it was them that have an open winding, but they are still operable.
I narrowed it down to wiring between the trailer hook up and passenger light assembly in the electrical circuit. I plugged an LED light bar into the trailer connection and the same problem occurred (running lights come on, but no turn signal or brake light). Where could there be a short? Or is this circuit fused somewhere that the running lights come on but a separate fused circuit triggers the higher voltage for LEDs.
View 9 Replies
SO, my Buick has given the code for bad TPS, and it was replaced a little over a year ago...and now after the same symptoms, replaced again.. However, this time, right after replacing, it gave the code again, and still stalls out /doesn't want to stay running especially when put in gear. My regular mechanic also recently just put on a new catalytic converter and a new fuel pump and fuel filter. I'm at a loss, and desperately need my car back.
A little back history...about 3 years ago a 'friend' was to work on my car to install the thermostat and power washed the engine...which shortly after started having all kinds of electrical issues. Right after that, my mechanic had to install a coil, spark plugs, new ignition panel and the 1st tps.
View 8 Replies
1998 Jeep Cherokee sport ... My mechanic tells me that my #1 fuel injector is always spraying and that that is why the jeep runs rough. This is after he already told me that my injectors were clogged and needed to be replaced (which he did). When the car is idling for a while, the exhaust really begins to smell like gas, so this seems to make some sense to me, unlike his previous diagnosis. But now he is telling me that I need to replace the computer to fix this problem.
View 8 Replies
My wifes 2011 Hyundai Sonata would not start yesterday at the clinic. I purchased a new battery went there today to replace the battery. Before I started the work I tried starting the car. When I turned the key to the on position the radio came on and the dashboard lit up like normal. As soon as I turned the key to start the car the battery went completely dead. The starter did not engage and the electrical went out.
I replaced the battery. When I turned the key to the on position nothing turned on. Not the radio or any of the dashboard lights. I tried starting the car and there was not response, exactly like a dead battery. I purchased a new battery and they tested it right in front of me before giving it to me so I feel like I can rule out the battery.
I double checked that he connections were tight. I tried jiggling the shifter, pushing the brake pedal, jigging the steering wheel around, jiggling the key in the ignition. The positive battery terminal connector has a fuse, it appears to be intact. I also checked the fuse panel in the engine compartment. All of the large fuses are intact (I only looked at the 3 or 4 of the large ones that were visible from the top). I didn't check the smaller fuses, I wasn't sure which ones to check.
A little background : For a couple days in a row my wife was noticing that the car was struggling to start (she didn't mention this to me right away). I noticed that when we were driving it the head lights had a very subtle flicker. When were idling at a stoplight it appeared as if the lights were dimming and getting brighter rapidly. I noticed it from the reflection of a license plate and dismissed it as maybe just the wind causing the license plate on the car ahead of us to wobble. It was subtle and not very pronounced. Yesterday my wife went to the clinic and when she was leaving the car would not start. Someone tried with jumper cables but she was not able to get it started. Even after letting it sit for 5 minutes before trying to start it.
My buddy thinks it's the ignition switch itself, but that sounds quite a bit beyond my capacity. I suspected that since the lights were fluttering/dimming that it was an alternator problem. Even if the alternator is bad wouldn't the car still run on a fresh battery?
View 11 Replies
My wifes 2011 Hyundai Sonata would not start yesterday at the clinic. I purchased a new battery went there today to replace the battery. Before I started the work I tried starting the car. When I turned the key to the on position the radio came on and the dashboard lit up like normal. As soon as I turned the key to start the car the battery went completely dead. The starter did not engage and the electrical went out.
I replaced the battery. When I turned the key to the on position nothing turned on. Not the radio or any of the dashboard lights. I tried starting the car and there was not response, exactly like a dead battery. I purchased a new battery and they tested it right in front of me before giving it to me so I feel like I can rule out the battery.
I double checked that he connections were tight. I tried jiggling the shifter, pushing the brake pedal, jigging the steering wheel around, jiggling the key in the ignition. The positive battery terminal connector has a fuse, it appears to be intact. I also checked the fuse panel in the engine compartment. All of the large fuses are intact (I only looked at the 3 or 4 of the large ones that were visible from the top). I didn't check the smaller fuses, I wasn't sure which ones to check.
A little background;For a couple days in a row my wife was noticing that the car was struggling to start (she didn't mention this to me right away). I noticed that when we were driving it the head lights had a very suttle flicker. When were idling at a stoplight it appeared as if the lights were dimming and getting brighter rapidly. I noticed it from the reflection of a license plate and dismissed it as maybe just the wind causing the license plate on the car ahead of us to wobble. It was suttle and not very pronounced. Yesterday my wife went to the clinic and when she was leaving the car would not start. Someone try with jumper cables but she was not able to get it started. Even after letting it sit for 5 minutes before trying to start it.
My buddy thinks it's the ignition switch itself, but that sounds quite a bit beyond my capacity. I suspected that since the lights were fluttering/dimming that it was an alternator problem. Even if the alternator is bad wouldn't the car still run on a fresh battery?
View 11 Replies
So i have a 2005 Sonata GLS and it has been giving me issues. A week or so ago, the 'check engine' came on so I took it to the shop to have it fix. Problem fix, no more light popping up. Now two days ago, the car all of a sudden started stalling and hesitating while I was driving. I kept pressing the gas and the car will accelerate to 40 before slowing down to 20 and the acceleration will then drop as well. I had a mechanic look at the issue and he said it was the throttle position sensor. He changed the sensor and its still acting up. He said to buy the carburetor cleaner and it worked fine for a hour until we drove it again. The problem is still not fix.
View 3 Replies
I am a beginner when it comes to anything involving wiring. I am looking to re-wire all of the wiring coming off of the instrument cluster gauges. Once I have completed all of the wiring on the gauges, I may feel confident to move onto something else. As of rite now, it appears as though my truck is still running on all of the original wiring, and over the past few weeks, I have been having many wiring related issues. I found a schematic that includes the wiring for the gauges that I am going to go off of. I have a couple of questions before I begin.
1.) On the schematic, it shows connectors such as "Connector G" which is moving all of the gauges wires to there locations. Do I need to use a specific Ford connector, or could I purchase a new connector at any hardware store that carries them? As far as I am concerned, connectors do the same thing as all other connectors. (Let you connect and disconnect for easy instrument cluster removal.)
2.) I am not looking to purchase one of those expensive wiring harnesses. I would like to just purchase some wire that I can cut / use myself. What brand / type of wire should I be looking to purchase? I do not care if it is striped / colored as I will use wire tabs to name / label each wire.
Other than that, I feel confident enough to attempt something such as this. Here is the wiring schematic I am going to use.....
View 10 Replies
Any COMPLETE headlight switch wiring diagram? Everything I find online only shows 2-3 wires in each sub connector, nothing with all wires and colors, and what they do. and of course the factory service manuals no longer work on my new computer. the switch and associated wires went up in smoke 2 hours ago, and this truck is my only means of transportation rite now. what i need is headlight wiring with colors so i can temporary hook up a toggle switch to have lights until the new switch and connectors come in next week. I went to pull the switch and connectors out of the parts truck, but of course that does not have fog lights so it uses different switch and connections.
View 14 Replies
I plan on moving the engine/drivetrain from my 1986 F350 460 to my 1996 F250. I also want to move over the 1986's ignition system with a Duraspark 2 setup.
Although I could just cut in the easiest places to remove the wiring for later reuse I am looking for where to make the cuts, what to take and what to scrap. Alternatively I am also asking if there are aftermarket or OEM replacement sets out there are aren't a ton of money. The current harness in the 1986 has been sprayed with engine oil and cooked for 27 years so I am looking at alternative options if there are any.
View 8 Replies
I have a 97 F250 HD. Wiring the rear tail lights. When we bought it the had cut off the wires going to both sides of the rear lighting assemblys and I was wondering what wire went to what i have the left turn signal working just can't seem to get the brake/back up light to work on that side and i can't figure out how to get the right side going either.
View 8 Replies
Looking for a source for a wiring diagram for the 2003/4 f350 instrument cluster, specifically the wiring/connectors to the gauges? A link to a PDF file would be nice. I would like to try and disconnect the PCM control to the transmission temperature and engine temperature and drive the gauges from my own sensors to bypass the non-linear behavior that ford decided was in our best interest. I am NOT interested in installing any more gauges, just want to control the ones already present with my own signals. It is possible that these gauges are all addressable devices on a common bus, instead of individual controls.
View 8 Replies
Just bought an 04 Super duty with the factory plug 7pin and 4 pin plug. Checked the fuses and finally tracked down the 2 relays under the hood but can't seem to find anything wrong. Everything on the trailer works except for the running lights. Is there another fuse or something I have missed? Trailer works fine on my buddies Duramax and worked fine on my old 97.
View 14 Replies
