My camshafts got moved while replacing tb & wp.v6. Can I get TDC bringing #1 valves closed & #4 valves open & then bring crankshaft the TDC mark? Interference engine, valves not damaged!!!
View 7 RepliesSo, I got a 01 b5 1.8 5spd given to me was broken timing belt. The car is super clean with 226k on it and had been well-taken care of..oil changes Mobil 1 and such. the owner just got his $$ worth and drove it till the belt went, slapping then towed it to my shop. It did not overheat and he was not driving it hard. Now here is my real question...apars lapping on a new belt and crossing my fingers, what testing can I do to check and see if there are any valves damaged? Can't I do a compression test w/out the valve train in time right? Also, if there does happen to be head damage. I would be in the market for an AUG head, unless it's just a valve that can be replaced....
View 6 RepliesI have 2004 Chrysler Sebring base model 4 cylinder with 90,000 miles. Paid off long ago. The schedule says its time to change the timing belt but no symptoms. No other issues and have kept up the maintenance. The cost is around $1000. I need the car to last 2 more years until our new car is paid off. Should I do the repair or play the odds that it won't break down?
View 19 RepliesI have a 2005 Chrysler Sebring. In December the timing belt failed while I was driving down the road. I had the dealership I purchased the car from replace the timing belt as well as the water pump while they were at it. Ever since I have had and issue with it vibrating at idle. At first it was making a whining noise as well. I took it back and they told me that they had installed the belt too tight. Afterwards I still had an idle issue although the vibration was a little different. I also could distinctly hear the belt hitting the casing a few times.
I took it back again and they stated that the belt had been put on too loose. So now they have adjusted the belt again and it I am no longer having the whining or belt hitting the casing. But I still have an idle issue. It has changed again and is kind of a pulsing vibration. I can feel it in the brake pedal when I am at stops. I seem to hear the pulsing while driving as well but this may be from my new tires as well.
During this whole readjustment process they have not mentioned actually checking the timing. Just the belt tension itself. When I first reported the idle issue after they put the timing belt and water pump on they told me that it could not be related to timing and that it had to be an ignition issue. But I asked a work associate who used to work as a mechanic and he stated that it would be a timing issue.
I am going to contact the dealership and ask them to check the timing belt again. I never had this idle issue before the new timing belt.
I recently bought a 97 960. i have had a s90 before in totaled it i loved the car so much i found another. i was driving and broke the timing belt tensioner which in turn lead to the breaking of 5 exhaust valves that i know of. I've taken off the head and noticed that one of the bottom of the valves had melted onto the number 5 piston head.
I called around and search but every motor is at least 1000 and i have been told anywhere from 3500-4500 to rebuild. My question would b is there an easy way to fix or should i junk it. i bought it for a 1000 it has only 140000 on it an its in almost great condition. I attached some pictures of the head and piston so u can see the damage.
Attached File(s)
2012_04_07_19.02.39.jpg ( 1.45MB )
2012_04_10_16.45.26__1_.jpg ( 1.43MB )
Totally stumped. Replaced the head gasket in Nissan 03 Sentra 3 months ago and car has been running great since with good power. Car suddenly completely dies after coming to a stop without any warning or any loud noises.
No compression in all cylinders. Seemed to be lots of oil in all four cylinders according to the bottom of the spark plugs. Pulled timing cover, timing marks still line up perfectly. Leak down test suggests valve problem.
Pulled the head and see all the exhaust valves are bent and the intakes are bent on pistons #1 and #3. (which is also odd as pistons #1 and #4 run in the same positioning) Question is how can all the exhaust valves suddenly get bent simultaneously with the timing chain still registering perfectly on the marks it's supposed to?
Things I've checked: I checked to see if the camshafts have sheared through the key, but they seem fine. No deep grooves found to indicate they slipped or anything.
I have a 2004 Chrysler Sebring with a 2.4L dohc and automatic transmission with 115k miles. I recently had the timing belt and water pump replaced. Shop left the front 2 engine mounting bolts off and the rear one loose. Picked up car after business hours drove it that evening and kept hearing a strange metallic squeak.Returned it to the shop the next morning and as i was driving it began to smoke and stall with the temp gauge pegged. They had also left a hose to the heater core disconnected. Could the engine not being mounted to the chassis and/ or the overheating have damaged the transmission.
View 3 RepliesGot a bit of a problem with my car. Earlier this week, I got in and noticed there was heavy condensation on the inside of the windshield of my 2002 Chrysler Sebring convertible. The windows had been rolled up and the top up of course. I see this kind of condensation happen on the outside a lot in the mornings. You know, dew settling and all that. If I wait around until later in the day, it evaporates on its own.
Anyway, this time it was on the INSIDE. I wiped it clean easily enough and was on my way.
Today I noticed that my heater wasn't working. The temperature gauge goes up to about 1/3 of the way, so I know the car is warming up. I'm not sure if it normally goes up that high; I don't usually pay much attention to the temperature gauge.
I have an '06 Sebring convertible, 2.7l, V-6, 58,000 miles. When stopped with A/C on, car tends to surge. When I put in neutral, surging stops. Also, I sometimes get a "thump" (with both sound and feel) like I've been rear-ended, but have not. Dealer did tranny serivce and replaced all plugs and 2 coils which they said were "arcing". Did not fix problem. What would be wrong with A/C so as to cause this?
View 5 Replies2000 Chrysler Sebring Convt quit while driving. Tow truck drive and a mechanic at scene of breakdown felt itt seemed like it wasn't getting gas. Replaced fuel pump, fuel filter, 2 sets of plugs ans it won't start and when it did it ran rough and then fouled out new set of plugs. Seemed like too much fuel going to cylinder.
View 1 RepliesMy oil light comes on when I stop but goes off when I'm driving. I check the oil level and it was fine. What would cause this? It's a 2001 sebring 2.7L
View 6 RepliesI have a 2002 Chrysler Sebring that broke down. Unfortunately it ran out of oil, and I was told that the car has 2 sensors that detected the lack of oil and shut down the engine. A local auto repair shop replaced the sensors. I paid the bill and began to drive the car home but I only got 20 miles away when the engine blew. My question is, if the the shop told me the car was fixed and then the engine blew, aren't they somehow liable for this?
View 19 RepliesI recently brought my 2000 chrysler sebring in because the alarm was going off at random times (3:00am). Also when I was driving the interior lights would turn on and off and the dash readout would say "DOOR" as if I had opened the door, there was a relay clicking sound under the dash and the car would also try to relock the doors. This was an intermittent problem, occasionally the car would be fine for a while then the show would begin. I took it to a local Chrysler dealer and they diagnosed the problem to be the BCM or Body Control Module.
My conclusion is that this whole problem was caused by a shorting door switch and that either they misdiagnosed the problem and when the new BCM did not fix the problem they found the real problem in the door switch or they just scammed me from the start. I think the "part exchange program" is a scam. Why don't I get the part back or why don't I get two prices, one if I exchange the part and one if I don't.
Could a faulty driver door switch damage a BCM? (I never heard of this before. In fact another dealer told me all he needed was the VIN to see if the part was in stock).
My daughter's 2001 Chrysler Sebring began "shaking and jerking" last night. She described it as similar to when a person drives a standard transmission that doesn't know how to do so. (Her car is an automatic.) She had been driving it for about ten minutes without a problem and had luckily just turned onto a residential street to pick up a friend. She said the check engine light came on as well. She was able to limp it to her friend's and leave it parked there.
Recent work on the car includes the thermostat being replaced and a resistor related to the heater blower motor being replaced. What might be causing this. She's probably going to have to have it towed.
ASD Fuse keeps blowing. I unplug PCM and fuse no longer blows. I plugged in pin 41-80 and the the fuse is still ok. Car just quit running and starter will not turn. Does pin 1-40 control starter and fuel?? Could I have a bad PCM??
View 2 RepliesI have the above mentioned 2005 Sebring Convertible (2.7L V6, Touring) and the AC will work occasionally, but when it is hot and humid, it is sure to blow hot. First up was to check the system pressure and top off if needed - not the problem. Also blew the bugs and junk from the radiator fins. The wires and electrical connections look good at a glance. Turning the car off and on again doesn't work. Why would the darn thing work part time and take days off when we need it most?
View 1 RepliesOil light comes on when I stop and goes off once I move again. Oil is full and just changed. What causes this & can I repair? I have a 01 Chy Sebring withh 100K miles on it. I bought new & have changed the oil every 3K miles since I have had it.
View 7 RepliesI have a 2008 Sebring convertible that has starting issues. Sometimes when I turn the key to start, it does nothing (no noises, maybe a small click very rarely). If I take the key out and put it back in, it may start. Usually, I have to turn the power on, move the gears, and try again. Sometimes, it will start immediately, or I may have to do this procedure several times. It has been taken into the Chrysler dealer twice. They said it was not the switch or alternator and replaced the battery that wouldn't keep a charge. It was a 5-yr battery with 3 years of use. I was told to drive more! I shouldn't have to charge the battery every day. Several diagnostic tests were performed with no results. It still did this twice after the battery was replaced. Could it be cables?
View 3 RepliesIn May 2011, I got into the passenger side of my 2006 Sebring to find the foot area full of water, and it wouldn't stop pouring in. So I had work done on the AC unit to fix a broken plastic part on the firewall. I am a snowbird who travels to Florida every fall, and subsequent to that work being done, I have had to have a line (?) cleared because the water drips into the driver's side when I turn right. After clearing the line, it seems to be ok. This year, I had the line cleared and the problem persisted. My mechanic cannot figure out what's going on.
View 2 RepliesIts a 1998 chrysler sebring jxi. 2.5 V6... It runs fine then randomly shuts off all electrical parts stay on i have to pull over or if it turns off at a red light let it sit for a while because i immediately get the "no bus" code. i have to let it sit with the car on but not trying to crank until the code goes away then it cranks again. sometimes i have to repeat that process a few times, sometimes just once. at times the code only last a couple minutes but sometimes over 10!
View 10 RepliesI've run into a problem while doing brakes on my friends 2005 Sebring. I can't seem to get the brake caliper off. There is a little rubber boot with a plastic cap that is where the bolts that hold the calipers in place are. How to get the bolts out to remove the caliper. In fact, it doesn't seem like there are any traditional bolt heads in the plastic cover.
View 2 Replies