I have a 2006 Chrysler Sebring Convertible 2.7L engine. Replaced water pump and spark plugs. We triple checked the alignment on the chain and are sure the timing is fine. Car started right up. Now running rough idle and engine light comes on. Codes read misfires on 1, 3, and 5 cylinders.
View 8 RepliesI have 11 tiguan 2.0T. When I start it up is runs rough below 1200 rpm. The check engine light starts flashing. The codes are all 4 cylinders for random cylinder misfire. When I go drive it around the roughness calms down but doesn't go away and the idle will start jumping up and down. It goes to 1500 back to 800. Then 1700 back to 800. It had even hit 2400 once. I have changed the pcv about 2 months ago. I checked it and it looks fine. One place said maf. I cleaned it and no change. Running out of options.
View 2 RepliesI recently purchased an 06 f150 fx4 5.4L with 60K miles. Just recently my check engine light came on and I've noticed a slight rough idle in park. I took it to autozone and the code read P0422 evap emission leak. Bought a new fuel cap but didn't work... EGR valve?
View 2 RepliesI have a 2004 Sebring my check engine light is on and the RMP's are really high while Im driving. What could be going on?
View 11 RepliesAbout a week or two ago, when driving home, my battery light flicked on while at a stop light. Also, as the light wen t green and I accelerated away, I noticed a kind of 'whine' from the engine, like a turbine spinning up. By the time I got home it was fine again and the light out, and has been until today, when it happened again...I noticed that it happens if I have the AC on and I'm at a stop. If I turn off the AC when waiting at traffic lights, that seems to eliminate the battery light, but I still here the whine.
View 4 RepliesI drive a 2002 Chrysler Sebring convertible with about 130,000 miles on it.
I was driving down the highway in early November when the check engine light came on my car. I took it to Aamco who did some diagnosis and replaced a solenoid assembly in the transmission. The light went off and I was on my way. I never got the exact code.
About a month after that, the light came on again. This time, I got a low end code reader and scanned it myself. I got a "P0700" code, which I've read is a generic code that the transmission system sends to the computer or something. So I used my reader to erase it. However, the light came on 2 days later while I was driving down the highway at about 70 MPH.
So I went to an auto parts store to get a more detailed scan with a better tool. This one came up "P0740 Torque Converter Clutch Solenoid Circuit".
This feels weird, because the solenoid assembly was just replaced a month ago (and is still under warranty).
The car seems to drive okay. I don't notice any actual problems in shifting. The tachometer seemed to get up to about 3000 RPM on the highway. But I've seen practically new cars do that. The last time I had serious transmission problem it would rev up to about 5000 or 6000 RPM on the highway and still only getting up to about 40 MPH. That was 3 years ago and at the time I had a fairly expensive transmission repair (which included a new torque converter).
But like I said, the car seems to be driving okay. I don't drive much. Maybe 100 miles a week? And even that is mostly optional in town driving. I'm not looking to keep this car for more than another 20,000 to 25,000 miles though for the time being I cannot afford a new one.
What are the possible causes here? What are the consequences of ignoring this? Like I said, it's still driving fine and as the old saying goes "if it's not broke, don't fix it".
2004 Chrysler Sebring Sedan, 4 cylinder dual-overhead cam. My check engine light came on this morning and the code came out as the catalytic converter. The car seems to be running fine, at least no recent changes. I'm debating replacing this vehicle soon, and I'm wondering if it's worth working on the catalytic converter. I recently replaced the cam shaft position sensor as well.
View 5 RepliesI have a mk4 1.8t Gti. Recently I have been having issues with idle and boost. I read the codes and multiple random misfires in all 4 cylinders came up, idle control and the crank, knock, and o2 sensor came up. Shows that system is running to lean as well. I changed the spark plugs and wires, check the coil packs they where done about 1k miles so I expect them to be perfectly fine. When I clear the codes it idles below 9-8k rpms. I also noticed the breather hose coming out of the valve cover into the EGT has a hole melted into it, could this cause any of my issues?
View 2 RepliesAfter a long trip from Houston to Dallas, my vehicle started to ride rough and eventually die on idle. It seems to idle fine, but then die after the first minute. I am getting code P306 and others all dealing with random misfires and misfires on ALL cylinders. The troubleshooting steps I have taken so far to no avail are:
(1) Replaced spark plugs with pre-gapped iridium
(2) Checked ignition coils
(2) Checked all vacuum hoses and air intake leaks
(3) Changed air filter(not a big deal)
(4) Removed and cleaned the throttle body with carb cleaner thoroughly
(5) Checked the intake manifold for leaks and did not find any.
(6) Computer PCM checked for updates and issues at dealer
The dealer said it needed new fuel injectors, which seemed kind of fishy due to the following symptom:
The car runs GREAT at highway speeds, but it is unable to maintain an idle for an extended period of time and dies due to misfires. I hear a chugging in the engine sometimes.
Due to these symptoms, I self diagnosed this as a fuel regulator?
I have a 2005 Chrysler Sebring. In December the timing belt failed while I was driving down the road. I had the dealership I purchased the car from replace the timing belt as well as the water pump while they were at it. Ever since I have had and issue with it vibrating at idle. At first it was making a whining noise as well. I took it back and they told me that they had installed the belt too tight. Afterwards I still had an idle issue although the vibration was a little different. I also could distinctly hear the belt hitting the casing a few times.
I took it back again and they stated that the belt had been put on too loose. So now they have adjusted the belt again and it I am no longer having the whining or belt hitting the casing. But I still have an idle issue. It has changed again and is kind of a pulsing vibration. I can feel it in the brake pedal when I am at stops. I seem to hear the pulsing while driving as well but this may be from my new tires as well.
During this whole readjustment process they have not mentioned actually checking the timing. Just the belt tension itself. When I first reported the idle issue after they put the timing belt and water pump on they told me that it could not be related to timing and that it had to be an ignition issue. But I asked a work associate who used to work as a mechanic and he stated that it would be a timing issue.
I am going to contact the dealership and ask them to check the timing belt again. I never had this idle issue before the new timing belt.
My 98 Chrysler sebring has a fast idle at about 1500, occasionally dies but will restart, and has been making the garage smell like gas. Can't seem to figure out the problem.
View 4 RepliesMy oil light comes on when I stop but goes off when I'm driving. I check the oil level and it was fine. What would cause this? It's a 2001 sebring 2.7L
View 6 RepliesOil light comes on when I stop and goes off once I move again. Oil is full and just changed. What causes this & can I repair? I have a 01 Chy Sebring withh 100K miles on it. I bought new & have changed the oil every 3K miles since I have had it.
View 7 RepliesI have a 2002 Chrysler Sebring that broke down. Unfortunately it ran out of oil, and I was told that the car has 2 sensors that detected the lack of oil and shut down the engine. A local auto repair shop replaced the sensors. I paid the bill and began to drive the car home but I only got 20 miles away when the engine blew. My question is, if the the shop told me the car was fixed and then the engine blew, aren't they somehow liable for this?
View 19 RepliesI have 2004 chrysler sebring and lately when I'm at a light/stop sign the rpm gauge fluctuates between 1000 and 500 and wants to stall. I've been told to change the spark plugs and wires, cleaned the throttle body, and put in a new air filter. What else I should do?
View 1 RepliesI own a 2007 Chrysler Sebring touring. I bought it used with 34,000 miles in 2009, and so far, haven't had too many real problems with it. Unfortunately, I'm rounding the ~65,000 mile mark and some weird things are finally going on. The transmission light comes on for a few days then turns off - for a few weeks one time, then it came back on for a day, and hasn't been back on for a few months. Also the Airbag light will bing on for a few seconds, turn off, then a few minutes later come back on, and this happens randomly. (It also recently threw a wheel weight it seems, but I'm familiar with how to fix that issue!)
A mechanic friend of mine told me that rather than paying money to repair this car, that I should get rid of it - he suggests Chryslers like mine become junkboxes right around 65,000 miles.
Engine oil has been changed and spark plugs changed. The engine is still making rattling/clicking noise. I checked with a mechanic and he indicated that engine needs to be repaired. Didn't say exactly what needs to be done and stated it would cost about $2200 for parts and labor. Why the engine keeps rattling and making the noise? Oh, before plugs were changed, the engine was shutting off at times when in idle mode.
View 5 RepliesI have a Chrysler Sebring 2005Engine cuts out at 2500 spurts stutters can't go above 35 mph...But still runs... No cruise available will not come on.. Engine light on... Which I guess from what I read is normal In "limp mode" Got it home.. Shut it off.. Starts back up.. I'm thinking cam/crank shaft sensor? Both of those are new.. And an ECM all from a prior problem.. Or fuel pump.?? Not enough pressure to keep up with demand..
View 4 RepliesA couple of months ago my daughter's Sebring engine began shutting off immediately after starting. We brought the car to my usually reliable mechanic. They couldn't find anything wrong. The problem became more frequent (every 2 to 3 starts) and we brought it back to my mechanic who determined it was the car's computer system. $1700 later the car is ready to be picked up, my daughter gets it after the shop is closed, and it wouldn't start! She left it there, got a ride, and, one week later the Sebring is still at the mechanic's. They told us it starts every time for them and they don't see any problem. After researching on the Internet I thought it might have something to do with the immobilizer but they told me that tested fine. I'm at a loss over what to do.
View 2 RepliesIf I make a right turn at anything above a snail's pace, my emergency brake light comes on and it chimes. Had the brakes checked and they are fine for now but since they are original, they will need to be replaced soon. The car has 50,000 miles. Recently had the cam sensor replaced and the dealership checked the car over.
View 6 RepliesHow to remove this type of connector from the brake light switch? I've tried just about everything at this point. Sheer force alone doesn't work. There has to be some type of release mechanism I'm not seeing that allows it to disconnect.
IMG_20161111_1433060_rewind.jpg3120x4160 1.96 MB