Sebring - Chrysler :: Blower Motor Will Not Stop / Error Code PO4091
Nov 8, 2015
Blower motor will not stop after engine is turned off. Is this a relay switch issue? Motor will run at very high speed. After a few minutes it would intermittently turn on and off. Battery was discharged two days ago. I forget how to test these relay switch, been a while since I've used my old DMM. Anyway, I've got an error code PO4091 (secondary air inj sys insufficient flow, bank 1). I lost the info on the two other error codes, but I will dig it up later and see if at all related.
Off topic. Found a vacuum line broken, reinserted the remainder of the tubing, so good for now on that end. It's by the TEE next to the battery. No wonder this one was stalling around 600 RPM and on low speeds around 600 RPM. New coils wires and spark plugs. Runs smoother now.
View 11 Replies
Advertisement
It's a 2005 Chrysler Sebring with a 2.4 DOHC. A couple weeks ago I tried to use the wipers and nothing happened - at all. The next day the gauges inside the car went hay wire, started flashing on and off. Turned out the car needed a new battery and alternator. Replaced both and the car has been perfectly fine - except for the wipers. I checked the wiper fuse and it wasn't blown so I pulled the cowl, unplugged the motor, turned the key on, turned the wiper switch to full speed and then tested for voltage at the plug and got almost 12 volts when testing several terminal combinations.
I thought for sure I had it figured out so went ahead and bought a remanufactured wiper motor but nothing happened when I plugged it in. I thought maybe since I didn't mount it it wasn't grounded so went ahead and did that and still nothing. Thinking maybe it was defective I returned it and went to a different auto parts store and bought another one, hooked it up and got the same results. So then I tested all nine relays in the relay control center and they all passed. So now I'm thinking the only thing left to test is the wiper switch. Am I correct?
And also I'd love to bench test the original motor just to verify that it works but don't know which terminals to connect to. I've searched the internet with two different browsers and came up with nothing. The motor in question is a Bosch 05-02-14 41. And then underneath it has 0390 241 7411 12V 058 written on it. The terminals are labeled: 31b, 31, 53 and 53b. And since the OE replacement motor for this car is a Cardone 40-3026, which terminals to use to bench test that one, I could then figure out which terminals to use on the Bosch.
View 19 Replies
My oil light comes on when I stop but goes off when I'm driving. I check the oil level and it was fine. What would cause this? It's a 2001 sebring 2.7L
View 6 Replies
Oil light comes on when I stop and goes off once I move again. Oil is full and just changed. What causes this & can I repair? I have a 01 Chy Sebring withh 100K miles on it. I bought new & have changed the oil every 3K miles since I have had it.
View 7 Replies
Its a 1998 chrysler sebring jxi. 2.5 V6... It runs fine then randomly shuts off all electrical parts stay on i have to pull over or if it turns off at a red light let it sit for a while because i immediately get the "no bus" code. i have to let it sit with the car on but not trying to crank until the code goes away then it cranks again. sometimes i have to repeat that process a few times, sometimes just once. at times the code only last a couple minutes but sometimes over 10!
View 10 Replies
I have a 2004 Sebring. The A/C had been working intermittently, now not at all. When it was working, if I went over a big bump or hit a pothole, it would stop blowing cold. Now it will not blow cold through the dash vents, but the defroster still blows cold so I believe there is enough coolant. The mechanic has discouraged me from investigating saying it will be very expensive to take the car apart to diagnose.
View 1 Replies
2004 Chrysler Sebring Sedan, 4 cylinder dual-overhead cam. My check engine light came on this morning and the code came out as the catalytic converter. The car seems to be running fine, at least no recent changes. I'm debating replacing this vehicle soon, and I'm wondering if it's worth working on the catalytic converter. I recently replaced the cam shaft position sensor as well.
View 5 Replies
I just wanted to post this due to the problem I was having with this code. I recently replaced a broken timing belt on my 2005 pt cruiser (non-turbo). Everything went back together, minus the hours trying to get the timing marks lined up by myself. After getting the engine buttoned up, the car would crank and idle, but only after 2000 rpm and the engine code P0016 would show up. I went back into the engine, reset the timing belt, and cranked it before putting everything back together. Worked fine, so buttoned it back up and took it for a test drive.
Bam, same engine code pops up again, only this time the car acted like it wanted to go into limp mode for half a second after driving for a few miles when I was turning around to come back to the house. It straightened up and drove fine. I could drive the car fine even after that, made a few test drives into town. The car would kind of fight limp mode after first cranking the car and accelerating, but then straighten up.
After a couple of months of research and talking to a friend who is a pretty good mechanic, I decided this was an electrical problem. I checked, and sure enough, after looking at the wiring at the cam shaft sensor connector, it was frayed. I spliced it and still had some issues with the code. I had just put a new sensor on it when the belt broke thinking it might be the sensor, so I put the old sensor back on it and now it runs fine, no more light. So, after months of thinking the timing or tone rings might be off, it was just a wiring/sensor issue.
View 7 Replies
2006 PT Cruiser Touring Ed. The engine light came on 2 days ago, had it looked at today and the error code p0304 "cylinder number four misfire" was diagnosed. What causes that and what would need to be done to fix that problem?
View 9 Replies
An MIL light came on the dash the other week while driving. Dealer cleared the error code but next morning it returned. Car is now in the shop to have the flapper motor and canister can replaced. Get it back tomorrow, Got '08 Jetta 2.5 as a loaner. I will run out of warranty in another couple of weeks(48100 mi. on it now).
View 10 Replies
I have a 2004 Chrysler Sebring with a 2.4L dohc and automatic transmission with 115k miles. I recently had the timing belt and water pump replaced. Shop left the front 2 engine mounting bolts off and the rear one loose. Picked up car after business hours drove it that evening and kept hearing a strange metallic squeak.Returned it to the shop the next morning and as i was driving it began to smoke and stall with the temp gauge pegged. They had also left a hose to the heater core disconnected. Could the engine not being mounted to the chassis and/ or the overheating have damaged the transmission.
View 3 Replies
Got a bit of a problem with my car. Earlier this week, I got in and noticed there was heavy condensation on the inside of the windshield of my 2002 Chrysler Sebring convertible. The windows had been rolled up and the top up of course. I see this kind of condensation happen on the outside a lot in the mornings. You know, dew settling and all that. If I wait around until later in the day, it evaporates on its own.
Anyway, this time it was on the INSIDE. I wiped it clean easily enough and was on my way.
Today I noticed that my heater wasn't working. The temperature gauge goes up to about 1/3 of the way, so I know the car is warming up. I'm not sure if it normally goes up that high; I don't usually pay much attention to the temperature gauge.
View 9 Replies
I have an '06 Sebring convertible, 2.7l, V-6, 58,000 miles. When stopped with A/C on, car tends to surge. When I put in neutral, surging stops. Also, I sometimes get a "thump" (with both sound and feel) like I've been rear-ended, but have not. Dealer did tranny serivce and replaced all plugs and 2 coils which they said were "arcing". Did not fix problem. What would be wrong with A/C so as to cause this?
View 5 Replies
2000 Chrysler Sebring Convt quit while driving. Tow truck drive and a mechanic at scene of breakdown felt itt seemed like it wasn't getting gas. Replaced fuel pump, fuel filter, 2 sets of plugs ans it won't start and when it did it ran rough and then fouled out new set of plugs. Seemed like too much fuel going to cylinder.
View 1 Replies
I have a 2002 Chrysler Sebring that broke down. Unfortunately it ran out of oil, and I was told that the car has 2 sensors that detected the lack of oil and shut down the engine. A local auto repair shop replaced the sensors. I paid the bill and began to drive the car home but I only got 20 miles away when the engine blew. My question is, if the the shop told me the car was fixed and then the engine blew, aren't they somehow liable for this?
View 19 Replies
I recently brought my 2000 chrysler sebring in because the alarm was going off at random times (3:00am). Also when I was driving the interior lights would turn on and off and the dash readout would say "DOOR" as if I had opened the door, there was a relay clicking sound under the dash and the car would also try to relock the doors. This was an intermittent problem, occasionally the car would be fine for a while then the show would begin. I took it to a local Chrysler dealer and they diagnosed the problem to be the BCM or Body Control Module.
My conclusion is that this whole problem was caused by a shorting door switch and that either they misdiagnosed the problem and when the new BCM did not fix the problem they found the real problem in the door switch or they just scammed me from the start. I think the "part exchange program" is a scam. Why don't I get the part back or why don't I get two prices, one if I exchange the part and one if I don't.
Could a faulty driver door switch damage a BCM? (I never heard of this before. In fact another dealer told me all he needed was the VIN to see if the part was in stock).
View 6 Replies
My daughter's 2001 Chrysler Sebring began "shaking and jerking" last night. She described it as similar to when a person drives a standard transmission that doesn't know how to do so. (Her car is an automatic.) She had been driving it for about ten minutes without a problem and had luckily just turned onto a residential street to pick up a friend. She said the check engine light came on as well. She was able to limp it to her friend's and leave it parked there.
Recent work on the car includes the thermostat being replaced and a resistor related to the heater blower motor being replaced. What might be causing this. She's probably going to have to have it towed.
View 1 Replies
ASD Fuse keeps blowing. I unplug PCM and fuse no longer blows. I plugged in pin 41-80 and the the fuse is still ok. Car just quit running and starter will not turn. Does pin 1-40 control starter and fuel?? Could I have a bad PCM??
View 2 Replies
I have the above mentioned 2005 Sebring Convertible (2.7L V6, Touring) and the AC will work occasionally, but when it is hot and humid, it is sure to blow hot. First up was to check the system pressure and top off if needed - not the problem. Also blew the bugs and junk from the radiator fins. The wires and electrical connections look good at a glance. Turning the car off and on again doesn't work. Why would the darn thing work part time and take days off when we need it most?
View 1 Replies
I have a 2008 Sebring convertible that has starting issues. Sometimes when I turn the key to start, it does nothing (no noises, maybe a small click very rarely). If I take the key out and put it back in, it may start. Usually, I have to turn the power on, move the gears, and try again. Sometimes, it will start immediately, or I may have to do this procedure several times. It has been taken into the Chrysler dealer twice. They said it was not the switch or alternator and replaced the battery that wouldn't keep a charge. It was a 5-yr battery with 3 years of use. I was told to drive more! I shouldn't have to charge the battery every day. Several diagnostic tests were performed with no results. It still did this twice after the battery was replaced. Could it be cables?
View 3 Replies
In May 2011, I got into the passenger side of my 2006 Sebring to find the foot area full of water, and it wouldn't stop pouring in. So I had work done on the AC unit to fix a broken plastic part on the firewall. I am a snowbird who travels to Florida every fall, and subsequent to that work being done, I have had to have a line (?) cleared because the water drips into the driver's side when I turn right. After clearing the line, it seems to be ok. This year, I had the line cleared and the problem persisted. My mechanic cannot figure out what's going on.
View 2 Replies
