Sebring - Chrysler :: 2001 Mitsu 3.0L Engine - AC Alternator Belt Hanging Under Car
Jul 15, 2012
Earlier today i noticed a loop hanging under my car. When i removed the item it turned out to be my AC/Alternator belt. Thinking it was bad i went ahead and got a new one. Prepared for a hard battle i find that the part slips on easily. now i can not get the belt tight at all it had about an inch or 2 of slack. I do not have a repair manual and i do not have the money for one. I can not find a diagram for my specific engine. It is a 2001 Chrysler Sebring with a Mitsubishi 3.0L 24 Valve Engine. What am I doing wrong? I need this fixed to go to work tomorrow.
View 16 Replies
Advertisement
A couple of months ago my daughter's Sebring engine began shutting off immediately after starting. We brought the car to my usually reliable mechanic. They couldn't find anything wrong. The problem became more frequent (every 2 to 3 starts) and we brought it back to my mechanic who determined it was the car's computer system. $1700 later the car is ready to be picked up, my daughter gets it after the shop is closed, and it wouldn't start! She left it there, got a ride, and, one week later the Sebring is still at the mechanic's. They told us it starts every time for them and they don't see any problem. After researching on the Internet I thought it might have something to do with the immobilizer but they told me that tested fine. I'm at a loss over what to do.
View 2 Replies
I have 2004 Chrysler Sebring base model 4 cylinder with 90,000 miles. Paid off long ago. The schedule says its time to change the timing belt but no symptoms. No other issues and have kept up the maintenance. The cost is around $1000. I need the car to last 2 more years until our new car is paid off. Should I do the repair or play the odds that it won't break down?
View 19 Replies
My daughter's 2001 Chrysler Sebring began "shaking and jerking" last night. She described it as similar to when a person drives a standard transmission that doesn't know how to do so. (Her car is an automatic.) She had been driving it for about ten minutes without a problem and had luckily just turned onto a residential street to pick up a friend. She said the check engine light came on as well. She was able to limp it to her friend's and leave it parked there.
Recent work on the car includes the thermostat being replaced and a resistor related to the heater blower motor being replaced. What might be causing this. She's probably going to have to have it towed.
View 1 Replies
I have a 2001 Chrysler (Mitsubishi) Sebring Lxi Coupe with the 3.0-liter V6 engine and (in)famous Chrysler A-604 4-speed automatic transmission. Mileage is approx. 115,000. Several days ago, I was on the highway doing 60 mph when the car suddenly, and without making any noise, lost power, as if the engine had quit. When I gave it more gas, the rpm on the tach shot up quickly to 3500, but the car was still losing speed. The Check Engine Light never comes on. Long story short, I pulled over to the side of the road and got the car flat-bedded home. The engine starts and run normally, but the car will not move in any forward gears (drive, first or second) nor in reverse.
The OBD II module is not throwing any codes that are related to a transmission problem. The transmission fluid is not discolored and does not smell or look "burnt". The fluid level is at the full mark on the dip stick. Up to this point, the transmission has performed and shifted flawlessly. I have serviced the transmission regularly every 30,000 miles since buying the car with 60,000 miles on it. I have been reading that this transmission was one of the first to be designed with electronically activated shifting, and has been installed in many models of Chrysler cars, vans, and pickups starting in 1989. Any way to check whether this may be an electrical/electronic problem first before getting a tow to a transmission shop for diagnosis of an internal mechanical failure requiring overhaul or a new trans?
View 5 Replies
I have a 2002 Chrysler Sebring that broke down. Unfortunately it ran out of oil, and I was told that the car has 2 sensors that detected the lack of oil and shut down the engine. A local auto repair shop replaced the sensors. I paid the bill and began to drive the car home but I only got 20 miles away when the engine blew. My question is, if the the shop told me the car was fixed and then the engine blew, aren't they somehow liable for this?
View 19 Replies
I have 2004 chrysler sebring and lately when I'm at a light/stop sign the rpm gauge fluctuates between 1000 and 500 and wants to stall. I've been told to change the spark plugs and wires, cleaned the throttle body, and put in a new air filter. What else I should do?
View 1 Replies
Engine oil has been changed and spark plugs changed. The engine is still making rattling/clicking noise. I checked with a mechanic and he indicated that engine needs to be repaired. Didn't say exactly what needs to be done and stated it would cost about $2200 for parts and labor. Why the engine keeps rattling and making the noise? Oh, before plugs were changed, the engine was shutting off at times when in idle mode.
View 5 Replies
I have a Chrysler Sebring 2005Engine cuts out at 2500 spurts stutters can't go above 35 mph...But still runs... No cruise available will not come on.. Engine light on... Which I guess from what I read is normal In "limp mode" Got it home.. Shut it off.. Starts back up.. I'm thinking cam/crank shaft sensor? Both of those are new.. And an ECM all from a prior problem.. Or fuel pump.?? Not enough pressure to keep up with demand..
View 4 Replies
I have a 2004 Sebring my check engine light is on and the RMP's are really high while Im driving. What could be going on?
View 11 Replies
About a week or two ago, when driving home, my battery light flicked on while at a stop light. Also, as the light wen t green and I accelerated away, I noticed a kind of 'whine' from the engine, like a turbine spinning up. By the time I got home it was fine again and the light out, and has been until today, when it happened again...I noticed that it happens if I have the AC on and I'm at a stop. If I turn off the AC when waiting at traffic lights, that seems to eliminate the battery light, but I still here the whine.
View 4 Replies
I drive a 2002 Chrysler Sebring convertible with about 130,000 miles on it.
I was driving down the highway in early November when the check engine light came on my car. I took it to Aamco who did some diagnosis and replaced a solenoid assembly in the transmission. The light went off and I was on my way. I never got the exact code.
About a month after that, the light came on again. This time, I got a low end code reader and scanned it myself. I got a "P0700" code, which I've read is a generic code that the transmission system sends to the computer or something. So I used my reader to erase it. However, the light came on 2 days later while I was driving down the highway at about 70 MPH.
So I went to an auto parts store to get a more detailed scan with a better tool. This one came up "P0740 Torque Converter Clutch Solenoid Circuit".
This feels weird, because the solenoid assembly was just replaced a month ago (and is still under warranty).
The car seems to drive okay. I don't notice any actual problems in shifting. The tachometer seemed to get up to about 3000 RPM on the highway. But I've seen practically new cars do that. The last time I had serious transmission problem it would rev up to about 5000 or 6000 RPM on the highway and still only getting up to about 40 MPH. That was 3 years ago and at the time I had a fairly expensive transmission repair (which included a new torque converter).
But like I said, the car seems to be driving okay. I don't drive much. Maybe 100 miles a week? And even that is mostly optional in town driving. I'm not looking to keep this car for more than another 20,000 to 25,000 miles though for the time being I cannot afford a new one.
What are the possible causes here? What are the consequences of ignoring this? Like I said, it's still driving fine and as the old saying goes "if it's not broke, don't fix it".
View 7 Replies
I recently bought an 02 Chrysler sebring (4 cyl) When cold, it takes about 5-10 secs of cranking for engine to start. Is that normal?
View 4 Replies
image.jpeg3024x4032 2.6 MB
I was driving down the road for about 20 minutes. When I saw steam coming out. I was a block away from home so I thought I'd make it before anything bad happened. The light turned green and I hit the gas and a few seconds after that something popped. I continued driving and the engine screeched and I pulled into my driveway. I jumped out and opened the hood and there was coolant everywhere. Like covering the engine and the underside of the hood.
2002 Chrysler sebring...
View 14 Replies
I am on my 3rd engine in this car (known issues unfortunately) and for the past few weeks have had problems with the engine feeling like it is quickly cycling through normal and 'losing pressure' at MPH over 40 when gas is going into the system. Mechanic replaced oil pressure sensor but problem recurred on next drive and AC cooling went out at the same time.
View 6 Replies
2004 Chrysler Sebring Sedan, 4 cylinder dual-overhead cam. My check engine light came on this morning and the code came out as the catalytic converter. The car seems to be running fine, at least no recent changes. I'm debating replacing this vehicle soon, and I'm wondering if it's worth working on the catalytic converter. I recently replaced the cam shaft position sensor as well.
View 5 Replies
I have a 2002 Chrysler Sebring with 116,000 miles and over the past month the engine has shutoff as I am driving and once I park turn the key off and turn on it has started to run again. This has happened about four times and each time it has been difficult starting it after the car has stalled. The most recent time this happened when I went to restart the car, a grinding noise became apparent. The last few times that I have started the car the grinding noise would be heard only to ultimately fade away in about 15 seconds. The check engine light came on and went to get the code and it came back suggesting a problem with the camshaft position sensor, but I don't fee the noise is related to that.
View 1 Replies
I have a 2006 Chrysler Sebring Convertible 2.7L engine. Replaced water pump and spark plugs. We triple checked the alignment on the chain and are sure the timing is fine. Car started right up. Now running rough idle and engine light comes on. Codes read misfires on 1, 3, and 5 cylinders.
View 8 Replies
My 2002 Sebring won't start. Here's what happens:
Turn the key in the ignition. Engine makes no noise at all. It's sorta like when the battery died 2 months ago, except this time the power windows and doors work, the headlights and interior lights work, though oddly, the radio doesn't. The radio, FYI, is not the one that came with the car. I bought it back in 2010 after the cassette deck on the original broke and I needed something with an Auxilary connector to connect my Ipod to. I had it professionally installed.
So the car doesn't start. The engine doesn't make any noise. The headlights do come on. The dashboard lights that normally come on when you try to start it up (the check engine light, the airbag light etc., also do not come on at any point. I don't recall any particular clicking sounds when I turn the ignition. I do remember hearing these clicking noises (sort of a quick one time click for each key turn) when the car wouldn't start due to battery/alternator issues two months ago.
So I did a bit of research, and I think it's either the starter solenoid or the ignition switch. Am I far off base?
View 19 Replies
The alternator light on my 2001 Ford Escape 3.0L comes on intermittently. I've replace the alternator, belt, tensioner, and battery. I've check the wiring and the ground and there are no noticeable issues. When I first start up it never comes on. After about 30-40 minutes of driving it will start to come on intermittently. I've noticed that it always shuts off when taking off from a stop. I have the most trouble with it coming on while driving around the city and little trouble while cruising on the highway. I'm completely stumped. Is it possible for one of the other pulleys to be causing this if for instance some bearings were going bad and it was binding up or problems with the crankshaft slowing down the belt?
View 13 Replies
One of my belts squeaks. I've tightened one of them as far as it goes I think. The other one is the one with the alternator. Do I tighten the pulley bolt on the alternator to add tension to that one?
View 4 Replies
