Saturn - Vue :: 2004 - Lose All Acceleration After 3000 RPMs
Nov 12, 2016
I have a 2004 saturn vue. It is a 5 speed standard with a 4 cylinder engine. Now that I have that posted here is my problem. I have normal acceleration up until I hit 3000 rpms. At that point my low engine power light comes on and I lose acceleration. To explain that better, if I take my foot off the gas pedal completely and then try accelerate again nothing happens. My engine stays on but I do not have any reaction when I push on the gas pedal. When I run the computer codes it says it could be my accelerator pedal sensor or my ecm. I do not want to have to replace the ecm if I have to due to how expensive it is.
View 8 Replies
Advertisement
Symptoms- won't rev over 3000-3500 rpm's, upon acceleration (especially uphill) seems to struggle and won't accelerate much at all, seems as if trans changes fine. BTW, throwing no codes at present.
What I have already tried...new air filter, new fuel filter, had cat. check (was told stopped up but when removed found it was not and truck did the same even with cat. off), o2 sensor (upstream) replaced, battery disconnected to reset computer.
After reset of computer, runs a little better but still not good. Seems to start if you accelerate to quickly or when truck reaches around 40-45 mph.
View 11 Replies
I've been working on a 04 Buick rendezvous and it has a very loud high pitch squeal when revved past 3000 rpms. Along with a serious power loss when the squeal starts. Has a new power steering pump as of today. And I took the belts off and revved it and the squeal is still there. That rules out the squeal coming from the belts. It is coming from some where in the engine bay and I'm stumped. I was almost positive it was the power steering pump since it sounded like it was about to go. But alas it was not. I does a little squeak when first started but nothing when idling. I've heard of a squeal coming from a clogged cat and it blowing out the egr valve. The squeal is so loud that you can hardly stand near the car.
View 13 Replies
At the beginning December I put my brand new winter tires (general altimax arctics) on the factory steelies and put them on the car gearing up for the snow. Not to long after the install I notice that I was getting a very strong engine vibration starting at 3,000 rpms and it stopped around 3,100 rpms no matter what gear I was in. At first I though it maybe just the cold affecting the engine. Well...
Last week I put my summer rims and tires back on for the 1,600 mile trip to MO and back, and like magic, no more heavy vibrations. Smooth acceleration throughout the normal driving rpm range. I just changed the oil and tranny fluids Tuesday after we got back and with the warmer weather the car is running smooth as silk. Still an awesome car with awesome mileage and couldn't be happier.
View 7 Replies
Let's say I'm going from zero to forty, my RPMs will hit over 3000, but when it shifts, the RPMS will drop down to 2000-ish really hard, making the car jerk. It's not a smooth drop, it's like a split second. Upon acceleration there is also a very rapid knocking sound. There's no lights on my instrument cluster.
This trouble all started after I had my alternator die, then having the car towed a few months back. Ever since then this problem has been getting worse. Wat this could be?
View 1 Replies
I have a 2001 accent with a 1.6 .... It won't rev over 3000rpm's. It does not have any codes being set. If I unplug the IAC it will rev up just like normal. I tried replacing the IAC, TPS, and swapped ECM and nothing has changed it. I tested continuity of the IAC circuit to ECM and it tests good. Tested ground circuit and it tests good. Have correct voltage at sensor. Not sure what else to look at.
View 21 Replies
My fiance is having issues with her car. It seems under acceleration to buck and lose power. I know more about 1.8t's but hers is the v6.
View 5 Replies
So I just drove my 85 to san francisco and back to Los Angles this weekend to visit my girlfriend and i had high oil pressure all the way until i blew my valve cover gasket.
So i fixed it finally today and it ran fine for a couple blocks and then my rpms shot up to about 3000 rpm and wont come down at idle speed and the car wants to keep going while in drive.
Its a 2.4l 22re EFI
View 2 Replies
My oil pressure gauge jumps all over the place when I get over 3000 rpms. At lower rpms it is in the normal range and the engine sounds ok. How can I tell if this is the oil pump or the sending unit or the gauge? This is a 1980 CJ5 with a 151ci 4 cylinder.
View 2 Replies
I have a 01 b5.5 Passat. When I'm in tiptronic and I'm about to hit 3000 rpms, a really off noise goes off and it's like a grinding sound.... Like when your car doesn't want to go to the next gear!
View 1 Replies
Last night when accelerating from 40 to 60 mph I felt a "whoosh" and then the RMPs went to 3000 when I had my foot on the pedal. They dropped to 1200 if I let off. This morning the car would shift into reverse, but punching the accelerator did nothing. Other gears are fine. I rolled out of the drive, stopped at the mech and diagnostics showed only a bad speed sensor. I saw a post elesewhere that had a similar issue in 2006, same model Toyota Sienna 2000 xle. Mech pricing the transmission replacement. Could it just be malfunctioning speed sensor sending bad data to the ECM?
View 1 Replies
I have a 2012 Nissan Versa with a 1.6 Engine/CVT transmission. When going down a steep hill the RPMs rev up to at least 3000 or more...is this normal for a car to do this?
View 3 Replies
I have been having with my ford ranger. I bought this off my nephew bcuz he needed some money and never drove it due to it being a 5speed and he has a kid and a wife and no room. OK the issue I am having is in gear or neutral I can't get the 2.5 motor over 3000rpms in any gear at all. If you rev the engine up or r driving it when it hits between 2900-3000 rpms the motor acts as if it is going to die and looses all power until you let off the gas. I have replaced the following items on the truck. Oh by the way I have a Cam 2 hand held and there are no codes or warning lights. All new parts :
1) new fuel pump
2) fuel filter
3)new timing belt
4)new motor craft platinum plugs
5) new motor craft plug wires
6)new Mass air flow meter
7) clutch,pressure plate & throw out bearing along with new slave(that needed it replaced others since I was there)
8) exhaust tube behind motor(rotted out)
9) new idle control sensor (acts as elect. Choke)
Truck starts up real quick and idles fine, but when truck is cold the rpms @ 2500 does the same as when it is warm @ 3000 rpms. I even took it to the local ford dealer in my town. Youngstown oh @ Fred martin ford. They told me the wires should be replaced and plugs along with mass air flow valve. I called them after replacing it and told them no difference and the service manager told me to bring it in again and they will look again. Service manager told me he has never heard of this type of problem and I went to a local garage mentioned it to the lead mechanic. He said that is why he doesn't like fords they are to common in chronic problems and can't be fix without a lot of guess work. I have a Hanes manual and did everything it recommends to no avail.
View 14 Replies
Manual... I hear this buzzing sound, mostly during deceleration, on 2nd, 3rd or 4th gears between 2300-3000rpms, very annoying on 2nd and 3rd gears, but can still somewhat noticeable on 4th gear. Can also hear it on acceleration, sometimes on 2nd and 3rd gear, silent on 4th gear.
I've turned off soundaktor thru VCDS, but still hearing this sound so I was thinking that the hockey puck is still spinning, albeit not as annoying as when it's 100%. So I tried to disconnect it, still hearing that buzzing sound. I even removed all stuff from my car and it's still buzzing. Really annoying, specially if you just want to hear the sound of the engine braking on deceleration.
View 12 Replies
I've got an automatic transmission 2002 elantra 2.0 that I purchased in 2009. About a year after owning it a weird problem developed that I've just sort of lived with since. Between 25-40 mph my RPMs occasionally "bounce" persistently by an amount between 500 (mild) and about 1000 (severe). There's a bit of fluctuation insofar as what RPMs/speeds it happens at depending on outside temperature and how warm the engine is (higher temps correlate with this issue happening at higher RPMs and a more pronounced fluctuation), but it's a consistent issue every time I drive. It *seems* like my car is always trying to push down the revs, hits a certain low point depending on the gear/speed, then jumps up just a bit only to edge back down. Lather, rinse, repeat. It's not simply a display problem as I can feel and hear the engine revs changing.
No fluctuations at idle. Above 3000 RPMs it's ALWAYS smooth sailing. When I'm actively accelerating there's never a problem, even if my acceleration stays in the revolution problem range. The car is never in danger of dying, but if the cruise is engaged (ESPECIALLY in the 25-30 MPH range at operating temp) the car shudders uphill - I assume this is because the RPMs dip a bit too low for the gear the car is in. If I press the throttle the car responds normally. This bouncing RPM issue itself NEVER causes the car to shift gears in response, and if it's happening and the car DOES shift everything works fine until it goes back to trying to maintain RPMs in the problem range. When it happens I usually just increase speed by 5MPH and it goes away, though if the car is warm and the speed limit doesn't allow me to go fast enough to get out of the problem range it just does the same thing at the slightly higher RPMs.
When the problem started my car threw an OBD code - I didn't read it myself and brought the car to a random service shop who SAID they changed the throttle position sensor, and the code was gone, but a few days later it was doing the same thing without throwing a code. I tried changing the fuel pump thinking it was a fuel delivery problem, but that didn't solve anything. I put seafoam in the fuel system monthly so I'm fairly certain that fuel system gunk isn't an issue. The symptoms haven't changed AT ALL during the 6+ years this has been happening.
The kicker is that a few years ago I found a SUPERB mechanic - the first one I've ever actually trusted to be not only competent but also honest. Described the problem and even demonstrated it to him. When I brought in my car to have the struts and mounts replaced he spent two days trying to figure out what was causing the RPM issue too... and couldn't nail it down.
Possibly related: after starting the car - regardless of how long it's been running - there's a brief delay between pressing the gas pedal and the engine responding. Delay seems *slightly* longer the colder it is outside, but it's never more than a second and a half. No further delays unless I shut the engine off and turn it on again. Replacing the fuel pump didn't affect this matter whatsoever.
View 2 Replies
I own a Ford Ranger 2003, 5spd 6 cyl. My problem is when I'm driving and the engine is revving above 3000 rom's. It begins to sputter and buck as if the engine is running out of gas. It only lasts a few seconds. It ends as quickly as it starts. It does not occur each time when driving above 3000 rpms. My mechanic took the truck for a test ride and of course he could not find anything wrong. His advise was to wait until it got worse. I would rather solve the problem now. It is difficult and dangerous when trying to pass vehicles on the road.
View 2 Replies
Ok so a little back story, I have CEL codes 17748 & 17755 which basically tell me that I have a stretched timing chain. That being said, others say they have the same codes and their car runs like a champ and makes full power. Not sure the truth to that but whatever. Regardless, I don't know how a stretched chain would cause a sudden surge of power at certain rpm, but I do not know the ins and outs of this engine and ECU.
So, for some reason my car feels fine when driving around at low rpms, but when I take it above 3000 rpm or so with mild throttle, it feels a little weak. Now if I am giving it moderate throttle, once I hit the 3000 rpm range, all of the sudden I can hear my intake get louder and there is a sudden surge of power. Furthermore, it feels to me like as the rpms get higher, like over 4500-5000 range, the car feels pretty weak. I am not sure how the car should feel though because this problem has been like this since I bought it. I am pretty sure it's not making full power though.
I can see how stretched chains could lead to being out of timing which could mean low power up top, even though I don't know why the variable cam gears couldn't make up for this.. but what's up with this power surge thing?
View 8 Replies
Here is what happened: I was accelerating one colder morning while driving to work when the power just dropped. Then engine continued to run, but I had no power or acceleration over 3000 rpm. Since that time, that is how the car drives. It starts, runs, etc... but has no power (like rev limiter or something) over 3000 rpm. The turbo spools up fine. I do know my 02 sensors are old. The engine has 184k on it... not bad. Is this a head gasket situation?
View 3 Replies
We have a 2001 E320 4-Matic. Recently, it has developed a serious problem. Every now and then, when I come to a stop (e.g., at a red light), the car would shake/vibrate significantly. Even more importantly, the car seems to lose acceleration suddenly and unpredictably (not necessarily correlated with vibration at the stop). The latter problem goes away "for the moment" by switching off the engine and then restarting it. The Check Engine light has come on as well. The codes that are diagnosed are P2001, P2003, P200F, P2082, P2050, P20151, P2055, and P2053.
While there are several issues with the car, I am most concerned now with the two issues I highlighted above - sudden loss of acceleration and the vibration while stopped (both happening unpredictably). I took the car to two mechanics. The two mechanics seem to sharply differ on how to resolve the "sudden and unpredictable loss of acceleration" issue. One mechanic (Mercedes dealer) attributes the problem to issues with EGR valve and claims replacing that will fix the problem. The other mechanic attributes the problem to the Catalytic Converter which he says is broken and is causing sudden loss of acceleration (and yes, there was a rattle some time ago). The second mechanic does not disagree that the EGR valve (and the secondary air injection system) has issues but he says it is the Catalytic Converter which is causing the core problem of sudden loss of acceleration (and yes, there was a rattle some time ago).
View 2 Replies
I have had my 20th for about a month now and I feel like first gear is so slow. I usually shift around 3,000 rpms. I was wondering if 1st if just slow in these cars or if there's something wrong?
View 1 Replies
2002 Elantra engine is revving up to 3000 rpms when in neutral or park. I changed the Throttle Position sensor and it went right back to revving up. Code read P0121. What might be causing this? Seems like I get one thing fixed and then another code shows up..
View 2 Replies
