Saturn - Sl :: 2002 - SES Light Has Been On Constantly - Codes P0172 / P0300 And P0507
Dec 4, 2011
Saturn 2002 SL1 5-speed. My SES light has been on constantly for about a year (was intermittent before that) with the codes P0172, P0300 and P0507. The car also idle high (2500+) occasionally at stops. My mechanic said it is likely an intake gasket but would need a full diagnostic to determine and that is not a safety hazard to drive but that I am getting less mph. I can't afford to fix it now but I have an emission test due. Is there a way to turn to light in the mean time?
View 1 Replies
Advertisement
My son just left. We scanned his truck and got these codes.
P0172 Bank 1 rich P0300 random misfires P0303 cylinder 3 misfires.
I used the Torque APP Pro to check these codes. I went to live readings in the Torque APP and saw some readings for Long term and Short term bank 1 Readings.
They are all "greek" to me, and I don't recall what they were, but could get those readings tomorrow.
When I have done searches combining these codes together, I see changing spark plugs. P0172 alone gets me a different train of thought. Mainly CAT issues.
Also, his cranking to start is quite long. (A lot longer than my 6.0L would ever think of cranking) At least nearly 30 seconds of cranking. We are leaning toward first just changing #3 plug.
View 9 Replies
My car is misfiring, codes p0171 and p0300 come up on the code reader. It idles rough and has very little power. I have checked my exhaust , it is not plugged. When I unplug coil #2 while idling there is no change as to the engine performance so I switched the coils around with no difference when coil is unplugged on cylinder #2. I have changed the plugs, there is power to the coil, all plugs are firing and when removed plugs 2 and 3 are wet with fuel indicating I am getting fuel and fire. I have replaced the cam sensor with no change.
View 3 Replies
This morning I started my car and it was idling a little rough. The the Check Engine light began flashing - I immediately turned off the car and consulted this forum and my father the mechanic. After talking with my Dad and telling him that the car had sat for a week, he thought the issue was probably NOT the catalytic converter and thought it was probably related to the car sitting and possibly getting moisture in the gas. I started the car again (the roughness at idle seemed to have gone away) but the check engine light/malfunction indicator light (MIL) did not flash, it did come back on after a few seconds, but as a solid light . And as we've all read, it's OK to drive with a solid MIL.
I took the car over to Autozone and had the codes checked - P0300 (multiple cylinder miss fire) and P0301 (cylinder 1 misfire). I asked them to clear the codes. I has just put in new NGK spark plugs last month, so I didn't think it would be the plugs. I looked at a new coil pack for one of the cylinders. I decided to see if clearing the codes alone would work and drove home. No issues so far, no MIL, no rough idle, no hesitation (fingers crossed).
When I called the stearleship - they recommended I have the car towed, but would not speculate as to what the flashing MIL could be (catalytic converter or bad coil pack(s))...
View 3 Replies
04 trailblazer, 4.2. Running rough and SES light on. Had codes pulled and showed p0340 (CMP sensor circuit malfunction) and p0300 (Multiple engine misfire detected). Replaced the CMP sensor and left negative battery cable unhooked for 20 minutes or so to clear the codes. Upon start up no more SES light and idle was slightly better. Within seconds it SES was back and it is again running poorly. Cruise control is no longer functional as well.
View 7 Replies
My 2004 Cadillac CTS 3.6L started running rough, check engine light flashed on and off. Codes P0300 and P0303. The car has about 119000 miles. Could this just be the plugs? The car has been running fine up to today.
View 2 Replies
Just got a 98 f150 w/ 5.4 4x4 excab. It idles fine but under light accleration. It starts bucking and missing bad, if I step on it, it down shifts and accelerates fine. If I try to maintain one speed it misses bad. It is not throwing any codes right now. The check engine light did come on for like a minute but went back off before I could have it read. I hooked up a scanner just to see if any codes were stored and got p0300 and p0301. I am going to clean the MAF and check for vacuum leaks. I hear the rear plug and coils can get water in them causing similar problems.
View 8 Replies
Not real familiar with this code, given that my check engine light came on a couple weeks ago and they detected some errors and these codes appeared.
View 2 Replies
2007 Passat 2.0T ... I just purchased this vehicle and after about two weeks of driving it has gone bananas. I found a ton of oil in the spark plug holes, and installed a new valve cover gasket...It no longer leaks. I am getting P0171, P0507 codes and multiple misfire codes from all cylinders...
View 6 Replies
Still having problems with my 2.4l 2002 santa fe. At stand still the MAF readings are within range. At 2000rpm it reads 9.3 gm/s. the info I have says it should be between 7.89-9.83.
When driving along at 50mph, 5th gear, engine speed 2000rpm it reads approx. 25.0 gm/s. at 3000rpm it reads 48 gm/s. Is the MAF sensor faulty?
It is now not running very well with fault codes P0171(fuel system to lean) That code comes up whilst driving at speed. I also get P0172(fuel system to rich). I got that one whilst driving slowly in a car park.
View 3 Replies
So I didn't pass the smog check for the new used car that I just purchased 10 days ago. Although my old car (same model), was five years older, I never had this problem. I was told that it is a gross polluter. These are the problem that I have to fix:
OBD Fault Codes - P1128 Manufacturer specific codeP0411 Secondary Air inj Incorrect FlowP0172 System too Rich (Bank 1)P0134 O2 Sensor CKT Inactive (Bank 1 Sensor 1)
How this happens?? 2001 VW ...
View 4 Replies
My Solara is running horribly. Its acting like the fuel pump or regulator is acting up as it loses power while driving and pumping the pedal usually does nothing. Its so bad that I cant drive it since top speed is about 10mph. If I just slightly touch the gas while driving I can get up to speed a little. It stalls when idling often too.
One thing I notice is if I stop driving for a while (with engine running) sometimes I can then drive away and the engine seems almost normal for 1-2 mins with lots of power. When the engine is cold it usually drives for 2 mins before these problems start.
This is a 2005 Solara. 4cyl 2AZFE gas engine - automatic - all stock - roughly 100,000 miles on the clock.
Its giving 2 codes: P0172 and P2196
I have looked up these codes and from reading I thought to try replacing the MAF sensor - no difference.
It feels like I'm driving a car with a bad carburetor again - really bogs out and laggy and sometimes even sounds like its backfiring slightly.
A bit of history:
- a few months ago I got the P0031 code so I replaced the upstream o2 sensor and all was good for a month or so.
- then about a month ago I got the P0136 code so I replaced the downstream o2 but it was starting to run badly before I could install and when I replaced it there was no change.
- last week I was surprised to see codes P0113, 172, 300, 301, 302, 303, and 136 but found that the battery terminal voltage was 10.5v so I replaced battery and those codes do not come back now.
- I'm thinking that due to the bad battery maybe the o2 sensors were not a problem? The upstream replacement made no difference (though it was running fine-just the CEL came on), and the downstream replacement made no difference (runs badly before and after).
My guess is fuel pressure, regulator, or injectors but its just getting too expensive to try.
View 3 Replies
First off its a 2006 F150 king ranch with the intercooled roush kit and roush tune. Last couple weeks its progressed from a slight stumble on start up, to now after its been off for a few hours it may start and run rough for a second, or, it may start then die, and then have to crank for at least 5 seconds before it starts. After it starts it seems to run fine. I've thrown the P0172 and P0175 code a few times. I downloaded the torque android app and did some data logging. Can you learn anything from the long term fuel trim?
View 9 Replies
My girlfriend drives an 09 corolla (1.8L I believe). I have an OBDII bluetooth reader w/ Torque App so to identify the issue I can get some data:
Last week I was driving the corolla and I got P0031: HO2S Heater Control Circuit Low (Bank 1 Sensor 1). Car seemed to run fine without any issues. My girlfriend brought her car in to her "mechanic". "mechanic" who will replace have of your engine only to realize that your gas cap was cracked. He apparently replaced 02 Bank 1 Sensor 2 (I'm still trying to confirm this and to get the part # to make sure). He reset the ECU and she drove for about 30 miles after which these codes popped up:
P0172: System too Rich (Bank 1)
P0101: Mass or Volume Air Flow Circuit Range/Performance Problem
The car was idling rough. I reset the codes and the car was running fine until all monitor systems were ready. When Catalyst, 02 Heater & 02 Sensor are not ready everything is running fine and I don't see any error codes. I cleared ECU a few times. The last time I was able to drive for over 20 miles without any issues. Currently the only sensor not ready is 02 and car is running fine but I have a feeling once its ready the car will start having issues again:
Summary (if you don't want to read everything)
*P0031: H02S Heater Control Circuit Low (Bank 1 Sensor 1) - Car runs fine
*Mechanic replaces 02 Bank 1 Sensor 2 (Trying to find part # and double check sensor name)
*ECU reset and car runs fine for 30 miles
*P0172: System too Rich (Bank 1) and P0101: Mass or Volume Air Flow Circuit Range/Performance Problem
*ECU reset - car sputters and hesitates
*When all monitors are ready same codes (P0172 & P0101)
View 2 Replies
so i had a litle fun in the clay today ..and now my trucks check engine lights on ..i have a code reader im running a P0172 P01275 P2106 Ive cleaned the MAF and changed my air filter...still running the three codes afterwords no trouble with turning over starts right up and drives with a normal amount of power....its a 2004 5.4L V8 ...
View 12 Replies
2003 f150 5.4, 4x4 ... Truck is shaking pretty bad, idle bounces between 500 and 750, and its throwing p0172 (rich on bank 1), P0174 (lean on bank 2), and it looks like a misfire on cylinder 8 judging by that power graphy thingy. I'm going to check for a vacuum leak tomorrow on the PCV.
View 2 Replies
2005 4cyl. Vue with 54K... Steady CEL. Runs great. Absolutely no problem accelerating. Don?t hear or feel any misfiring. There is a slight rumbling sound when I first start to drive the car, but to me, the sound doesn't seem come from the engine, but rather underneath the car. It goes away when I continue to drive. Since winter began, I occasionally feel a very slight hesitation during idle?happened once or twice lately.
Again, I only feel justified in mentioning it simply because of the codes that were generated. None of my passengers have made a comment about the idle or the drive. My friend, however, made a remark that occasionally, there is a very very very slight hesitation at the downshift when braking. No crack in gas cap. Great fuel economy. No problems accelerating at all. Never hear or an actual misfire, which I take it, means a problem when accelerating, a jerking, or popping noise.
Took it to a dealer. Codes were 0300, 301, 302, 303, 304?302 generating most often. Dealer recommended new ignition module and plug replacement, but they said it wouldn?t be a guaranteed fix and that it may need EGR replacement (don?t hear knocking though) or be a burnt valve in the cylinder. No suction out tailpipe, no rotten egg smell (signs of burnt valve). What are the chances of burnt valve in a car with 54K anyway?
Also, my maintenance schedule claims that I don?t need new spark plugs until 100K. Is there anything else this could be such as a dirty injector system, fuel filter, fuel pump, or air filter? Again, overall, the car runs GREAT! Should I just wait and see if the misfire becomes more pronounced so when I take it to a mechanic, they won't be looking for a needle in a haystack?
View 4 Replies
Granddaughter showed up with her '02 Accent idle varying between 600 and 2500 rpm. Disconnected Idle Speed Control Actuator and engine runs at very high idle so apparently the ECM is unsuccessfully attempting to manage the idle and the ISC is functioning. Reading P0507 code. Checked for vacuum leaks beyond throttle body, found none.
The car was involved in a fender bender accident a couple days before the idle issue. No CEL until a couple days after the accident. The varying idle started many days after the CEL.
The wreak cut a half dozen wires in the area outside of the battery. She repaired them and I just finished redoing with solder and shrink wrap. Found no faults with her twist and tape repairs or any other damage to wiring. Varying idle still there.
View 3 Replies
I have a 2008 Canadian F250 SD 5.4 triton. Its got 224000km on it and began to get the dreaded 5.4 dieseling when hot and idling. I replaced the timing chains, guides, both tensioners and crank gear. I confirmed the cam timing was correct with the crank key at 6:00 and the chains marks on the R and L. I replaced 2 coils on cyl's 2 and 3. I replaced the MAF sensor, fuel rail pressure sensor, cleaned and confirmed working the crank sensor and both cam sensors. I fixed the broken Bank 2 cam sensor wires. I changed the plugs and replaced all 4 O2 sensors.
Now the truck idles great but when driving it bucks and coughs and has zero power. I cant even get to 80km/hr. The computer now shows codes P0172 and P0174 which means the Bank 1 is rich and the bank 2 is lean. The O2 sensors are working and moving around. The back 02 sensors are both reading in the 0.8Volt range but bouncing around. The front 02 sensors are both moving from 0.1 to 0.8 constantly. The long term fuel trims are +9.5% bank 2 and -4.7% bank 1 at idle. When the throttle is off idle they become +25% bank 2 and -25% bank 1 . How is this possible and what can I do to fix this engine?.
View 10 Replies
So i got two codes.... P0300 and P0305. I am thinking its the coilpacks because i changed the spark plugs a few months ago. Cleared it last week and came back today. What else could it be? And is it ok to just change one coil pack or do i have to do all of them? The recall was done in 2007.
View 3 Replies
I recently got a problem with my 2006 LX V6 with 65k mils on it. The car had a few times a rough Idle so I hooked up my OBDII scammer ant got two failure codes:
P0300 miss fire
P0276 problem with Injector #6
Which one is the cylinder #6. I took of the engine cover and checked the connectors to the valves in the front row. I assume cylinder number 6 is in the back row and hard to get access.
View 3 Replies
