Saab - 9-3 :: Stalling - Engine Just Stops In The Middle Of Cruising Along
Oct 21, 2013
I have a 2000 Saab 9-3, the 'Viggen' model, and it almost always runs just fine. But once in a while, maybe every couple of thousand miles, the engine just stops, in the middle of cruising along. The power steering goes dead immediately. So far, it has only happened in city driving, not going fast or accelerating hard. I can restart immediately by just depressing the clutch and running the starter. From other reading, I wonder whether it's the Direct Ignition Casset? The engine is the 2.3 L turbo.
View 6 Replies
Advertisement
I have an automatic 2006 GLS Accent that is having a few problems. The engine will crank, but doesn't turn over right away. It might take a few tries, but will always start. This happens intermittently. Sometimes it will do it first thing in the morning, or sometimes it will happen later in the day after several start ups.
It has recently starting stalling while coming to a stop or sitting idle at a traffic light. This is also an intermittent problem. Always starts back up after a few tries.
The check engine light is not on. I have not taken it to a mechanic yet since it doesn't always do it, and will most likely be tricky to diagnose. What the problem might be? I was thinking it might be a crankshaft sensor?
View 4 Replies
Car was idling and driving real rough and dying at stops. Turns out that the transmission mount was torn so I replaced it and verified that the other two motor mounts were good. Car was still running rough but on a drive with some jerky shifts (automatic) after about 20 miles all is well and I'm running as smooth as a baby's bottom with great turbo action. Cars just don't fix themselves. What could have been wrong? By the way there were no codes from the Tech ll. Using a pc of tubing I can't hear any vacuum leaks nor when spraying brake cleaner on the hose ends does the engine race.
View 3 Replies
I have a 2006 Saab 9-3 Aero that I bought back in August. Two weeks ago, I brought car into the dealership for a 90k road service. It had some idling issues (sometimes, upon starting it up (cold or not), the car would idle and sputter, but never actually die. During the tune up, they said there was a frayed cable, which they replaced.
Fast forward 1.5 weeks later. The check engine light has come on. And the car is now sometimes idling funny just as it was before, only now it actually sputters and actually dies sometimes upon start up. After it initially dies, if I start it up again, it runs fine up on the second start.
Took into the dealership this morning and after 2 hours of diagnosis, they say the check engine read-out is indicating the fuel pump pressure sensor is going out, and that's what's causing it to idle and stall. Is this diagnosis legit?
View 8 Replies
About 4 months ago, the car stalled out on the highway. I was going slow because traffic was building up and the car just stopped. I was able to get off to the side. I turned it off, waited a few minutes and then it started up with no problem. I drove it with many stops and starts for about 2 weeks until I could get an appointment with the dealer. The computer did not show a problem. Then in April, the same thing happened. This time, they replaced the Body assy-throttle and./or gasket. Yesterday, the same thing happened though not on a highway but on a city street. There is no noise before the stall, no warning.
View 2 Replies
SAAB 2007 9-3 - Recently my car has been having a rough idle and stalling on start up. It has been getting worse and I need it fixed ASAP for a long trip coming up. I cannot have this thing die on me while I'm 300 miles from home....
At stop lights the car will have a rough idle while in park and reverse. While in neutral, nothing. As soon as I accelerate, it goes away but does have a lack of power if I really push the pedal. Once I am in 3rd/4th gear, the car feels normal with no issues. If I am on the highway and slow down then need to accelerate, it goes back to losing power BUT if I change over to manual and downshift, car gains power and goes back to normal.
Here's what I have done so far:
1. Changed the spark plugs twice. Once with cheap ones, the second time with expensive ones. I also swapped out the boots.
2. Cleaned the MAP sensor
3. Cleaned intake sensor
4. Replaced air filter
5. Changed oil
6 New battery
The engines gives no codes whatsoever and I have taken it to a couple places and their readers don't see any codes. My SAAB has a built in fuel filter and this cannot be replaced unless you replaced the whole pump (to my understanding). I plan on buying some Seafoam today and see if that works. Also, I have been told to clean my air intake valve but I cannot get the damn tube off! I feel that if I yank and pull on it, it's going to damage the tube. I am not seeing any obvious leaks anywhere. One thing that is weird about my car, since I have bought it used a few years ago, my headlights/tail lights/blinkers go bad QUICKLY!
View 1 Replies
I was driving to work but Sonata stop in the middle of the road acting like ran out of Gasoline. But the fuel gauge showed 1/4. I was tried to crank few more times but didn't start. Called road side assistant, tow truck took it to nearest Hyundai dealer. After they inspect, your fuel gauge sensor is wrong, fuel tank is empty.
My 2013 sonata is showing 61500 miles on it. They asked me $450 to replacing the sensor because bumper to bumper warranty covers up to 60,000 miles.
I decide to fix it later, put little bit of gas and than fueled up all the way to the top at nearest gasoline station. Fuel gauge works again, it is now showing full tank. I do not know how long it will last but it is scary.
View 5 Replies
My 2005 V8 starting intermittant stalling when stopped for a light/ when cruising at 40 MPH; the car restarts, runs for 30 seconds and then conks out. Had the car towed to selling dealing (3000 miles since end of April, 05) and now waiting for a diagnosis. Dealer claims they have never seen this problem before.
View 1 Replies
Like the title says my truck has been stalling while driving. Accelerating or cruising it dies for a second, two at the most, and then just keeps chugging along again.
I thought i'd fixed the problem last year when I did injector O-rings and 50 cented my UVCH. It hadn't done it since, until two days ago. Started out with a two good solid stalls while gently accelerating up hill. I had thought maybe my fuel pickup foot had finely given up the ghost because I was below a quarter tank. But I filled her up full, and then she did it again about 50 miles of driving later.
I didn't catch the first four stalls on my torque app, because I'd just recently decided to stop logging every trip, with the thinking that it had been half a year problem free, why keep logging waiting for something that isn't going to happen. I did catch the 5th stall on the torque log. But I'm having trouble trying to figure out where it happened in a 30 min log.
First question where would yall start in tracking this thing down? Next what data actually should be logged? I think I've got some extra stuff in my logs that isn't necessary, and is maybe bogging down the system. I get one data point per second resolution on my logs. Are there ways to improve the resolution, will getting rid of some PIDs work?
Lastly I need to attack this thing smartly, without throwing time and money at unneeded parts. I had surgery and I've been out of work for 3 months and I'm looking at another 6 before I'm making money again, and there is no unemployment for the self employed. Also I only get 3-4 light weight upright hours a day to work, exceed that and I'm back on the couch battling swelling for a week.
Also is there anything I can do while driving to "flag" the stalls so I can find them more easily in the logs?
View 14 Replies
So my car just started randomly dying everytime i came to a stop. Just shudders and off and then when i go to restart it cranks no problem but will not start. If i just wait for about 5 minutes it will start right up again but then die on the next few stops. A few hours later i go try again and i get it home no problem but still kept the rpms up when i wasnt moving. Filled up with 93 and put some gas treatment and it seems to be fine. What can it be? just bad gas or water in it? or could it be battery, alternator or clutch?
View 9 Replies
I have a 2003 f150 2WD crew cab with a 4.6 V8 engine it has 178,000 miles on it. The other day after I started it to leave work it died on me without hesitation almost like the ignition switch was turned off I tried to restart and it would turn over but wouldn't start so I switched the ignition all the way off and it started right up, going down the road it did it again.
If I try to restart without turning the ignition all the way off it won't start but if I turn it all the way off it will start up first try, it has done it a couple times since and its the same way every time, where to start. My check engine light has been on for some time for something else so I don't know if it picked up a code or not I don't have a code reader to see if it has a new code...
View 2 Replies
My brakes are working fine, and the car starts up okay. However, when I press on the gas and go anywhere over 20 mph or so, my car will start, then stop, then start, then stop... Until I step off the gas. There's also a semi-frequent squealing noise whenever I press the gas. The Service Engine Soon Light is on. What it is?
View 4 Replies
I have a 2001 Ford Escort with 92,000 miles that recently has started stalling when coming to stops. It's especially bad on stop and go traffic. It starts up easily every time, and once I'm actually driving with steady speeds, it has no problems. I've had plans to go out of town this Memorial weekend and visiting friends about 200 miles away (400 round trip). The earliest that I can get the car into the mechanic is Tuesday. This trip would be mostly highways and very few stops, but I don't know if it's safe to do so. Would I potentially be causing damage to the engine?
View 7 Replies
My 2003 ranger xlt 4.0 has a stalling problem. The engine light came on in aug and I had it coded at AutoZ and there was a code for the oxy sensor, changed that and didn't work so I took it back. In oct I had it coded and it said the air int temp sensor which i was informed was part of the mas airflow sensor, changed that the beginning of nov, got the computer to reset and it still didn't fix it.
Took that part back and had it coded again a few days later and several codes came up AutoZ code 1732 and the the OEM number to cross for them were: P2195 , P0300 , P0316 , P0174 , P0171 , P2197 . Reset the comp yesterday and as soon as the light came on had them code it again and it came up AutoZ code 1732 OEM # to cross P2195. I guess my next step will be to take it to the dealers to get diagnosed..
View 4 Replies
I have a 1995 ford ranger v6 4.0 and for this week Ive been having a problem, stalling... It only happens when I do quick "stop and go" driving. Even sometimes at stop lights it wants to stall, the only way to keep it going is to keep my foot on the gas.
Now for a while when its cold or my truck has been sitting for a day or two the truck doesn't start on the first click.
I've had the fuel pressure checked, changed fuel pump, and starter. I have no check engine light on at the moment. Tomorrow I am gonna check with my scan tool just to make sure. But, it could be fuel pressure regulator, idle air control actuator, egr valve? How I should go along doing this?
View 14 Replies
My speedometer was intermittent for a while, stalling, then moving, but never above the actual speed. Now I turn it on, but as soon as I move, it travels up to 38mph then stays there until I turn off the engine, then it hangs for 4/5 seconds, then drops to zero.
I replaced the VSS in the rear diff, and the one on the tranny. I checked all fuses. There are no other dummy lights or indications. Bad ground? I'm hoping I don't need a new gauge cluster.
View 5 Replies
I'm trying to diagnose an issue my sister has been having on her 2010 with the V6. Dealer can't find anything wrong with it
She says when she stops to get gas, it has trouble starting back. Will crank, but not start. has to try it several times. Sometimes pumping gas will work. (Sounds maybe like IAC to me)
She says when she's driving, that sometimes it will quit. Best I can understand from her description, it's when she's off the throttle. She says most of the time it will start right back up then.
She also says sometimes when she's trying to crank it back, it acts almost like a bad starter, or battery. Starter getting slower, then speeding back up. Also says that sometimes it acts like it's low on power. She has to floor it to make it go.
My thoughts are IAC or faulty fuel pump?
View 5 Replies
Bought this truck a few months back. Nothing but problems. I always thought it has felt a little underpowered and hesitant. I chalked it up to being a 5.4l in a f250. Well now im thinking it has been a symptom all along.
Lately, the truck has been stalling at stops. Randomly, but not often. The truck idles at 750rpm when I start it, but after driving and then coming to a stop while in overdrive it idles at 400rpm. This seems too low to me.
It hesitates occasionally when giving it throttle. Just today it got really bad and was almost unresponsive. I would hit the throttle and it would just idle while randomly kind of shooting up in RPS and shuddering. It finally produced some error codes, it looks like, but I am afraid to drive it all the way to the autozone.
I am thinking TPS. Is the TPS attached to the pedal or is the TPS attached to throttle body under the hood? I've read some conflicting stuff about this. The good news is that if it is the TPS then it should act like a whole new truck after I replace it.
View 11 Replies
My mechanic wants to use an engine cleaner to add to oil, then blow it all out!! It's a 2001 Saab 9-5 with 110k miles and is starting to burn its semi-syn at the rate of 1 qt. per 1400 miles.He says there's no discernable leaks.Should I let him add anything? Just keep adding the oil?
View 17 Replies
The car started fine...upon pulling out of the parking lot, the check engine light came on. After a couple seconds, the engine slow cut out and then wouldn't restart. After 20 minutes, I tried again and it started. When I pressed the gas it would only creep. I then had to floor the engine to get it to move. I'm not sure but I don't think I felt or heard the car shift, it's an automatic.
View 1 Replies
I was going 65-70MPH on the highway and the engine suddenly shut down. I pulled over on the shoulder and tried to restart but the engine would start for a second then dies again. I tried several times but it would not start. Waited 10 min and tried again with no luck. I called a towing service and a friend to pick me up. The towing guy called me 40 min later and said the car starts fine. I have driven it for couple days since and tried to recreate the problem (warming the engine, accelerating hard to 5000 RPM, stop and go situation) but the car runs great. No problem whatsoever with power or jittering or unstable idle or starting the car.I talked to 2 mechanics and they both think it is the fuel pump failing. But I am not convinced since I could smell gasoline when I was trying to start it.I have no check engine light on and I checked for recorded codes with my BT OBDII tool – nothing.
Do you think it might be CPS? Wouldn’t I get check engine light on if it is CPS?
View 12 Replies
