Pontiac - Bonneville :: 1987 - Socket Size To Remove The Drive Axle Hub Bolts?
Apr 11, 2011
What size socket I need to remove the driveaxle hub bolts from this car? I can see the bolts are considerably larger than the socket I have for my Ford Tauruses, and I would like to eliminate the guess work before I go to carquest to get the proper socket. Unfortunately bringing the car to the store and trying sockets until I get one that fits is not an option, since the car is not running right now.
View 3 Replies
Advertisement
What size socket is used to remove a lug nut on a 2000 F350 4X4?
View 6 Replies
I need to replace both the struts and the control arm but I don't have a socket to fit, what is the correct size socket I need ....
View 9 Replies
I have a beautiful 2002 Pontiac Bonneville SSEI with just over 100k miles on it. I've been saving for a new set of tires and a new regulator for the rear window. The window suffers from the "pop and drop" syndrome but I have instructions on how to fix it myself when I can get the parts.
Yesterday, I started her up to go to my second job when I discovered I had no reverse. In drive, I could just creep forward at 3000 rpm. Fixing a transmission is probably the worst case scenario I could imagine happening.
I'm left with two options: Either find something simple I can do myself to get it moving again or get what I can for it and use the proceeds to buy a piece of metal to get back and forth to work.
View 7 Replies
Any newer model with aftermarket water separators? If so do they perform better than stock?
View 4 Replies
What is the proper socket size for the oil filter housing?
View 2 Replies
Some folks swear by a 5/16 8 point socket, of coarse I dont have one, so I want to make sure b4 i buy anything. Looking at adjusting the 2nd gear band on a 72ish C6 ... As you know its a square end bolt, I dont own the correct square end socket either, so any direction would be groovy
View 1 Replies
Want to replace the rotors on my '97 2wd truck. What size socket do I need for the spindle nut? Can't seem to find that information with a search. I popped off the dust cap and test fitted a couple of sockets after removing the cotter pin and cap that locks the nut in place. 1" too small, 1-1/16" a little loose, so I'm thinking this nut is metric and I want a 26mm socket?
View 3 Replies
1999 F250 CCSB Lariat 5.4, 2 wheel drive. I plan to replace the Driveshaft Center Bearing in the next few days. What size is the Nut that I have to remove to remove the yoke next to it so I can press the bearing off?
View 4 Replies
what size bolts are needed for the rear license plate?
View 7 Replies
I need to take the tranny (automatic) off the old engine (BEW).
What are type/size are the bolts connecting the tranny to the block?
The 2 bottom ones I got out using (assuming) 10mm (?) triple square.
What size (socket/tool) and type (triple square, torx, allen) are the others?
View 1 Replies
I have an ' 87 Dodge Caravan cargo van that came originally with 195-70-14 size tires. I recently got for free, a like new set of 205-75-14 tires that I put on to replace the worn old set. My question is how will this throw off my speedometer, say at 35 mph or at 55-65 mph on the highway?
View 6 Replies
I have a 2003 W8 wagon and my front turn signal bulb went out. I need to replace it, but am having some problems. I removed the high beam cover to get to the turn signal socket, but I am having problem removing the socket. I was able to turn the socket slightly and was hoping I could just pull it back, unfortunately it doesn't seem to want to move. Is there a trick to remove the turn signal socket so I can remove the bulb? I don't want to force anything in fear of breaking something. there has to be a way.
View 1 Replies
I fit yesterday my ProComp Leaf Springs 22415 in the back of my Ex. It took about 3hours with a couple of beers to get the work done. Are those springs huge and heavy.
I will change the front springs in about 2 weeks, but we figured out, that we will need there 4 longer Semi-rounded U-Bolts, because the leaf package is about an 1/2-3/4 inch thicker than the OEM-springs. My OEM are a 2Leaf Springs and those ProComps 22410 are 5 Leafs.
View 14 Replies
1995 Pontiac Bonneville cranks but wont start.
I've replaced the crank sensor and also the cam sensor with no luck, the car cranks with no start, when I used starter fluid the car runs, when i stop using fluid it shuts off what could it be.
Only has 38,000 Miles on it.
View 2 Replies
Well I have to make a long story short, suffice it to say this is a bit embarrassing, but I need an answer: I removed the 440-t4 transmission from my daughter's 1987 Pontiac Bonneville and had it rebuilt. After I replaced the unit I discovered I left off (and lost) the TV link and cable. I (miraculously)found the link and the cable, and I am wondering if I can replace the link without having to remove the side cover of the transmission, and what I can do to avoid dropping the TV link rod down into the trans while I am trying to reattach it to the linkage arm inside the trans thru the little TV link hole on the top of the trans.
View 5 Replies
Air ventilation on my 92 pontiac bonneville ssei. There is no air coming out of the dashboard or the floor. only to the windshield. What can be the problem?
View 3 Replies
My Pontiac also has oil on the engine now with the oil pressure at 120. It started at 40 then went to 60. I had the oil changed and they put 5w30 which they were not supposed to do. I wanted 10w30.
Is this a common problem with Pontiacs? Is there a non engine replacing solution? Will I have to tow it to the mechanic?
View 10 Replies
Yesterday this thing died on me twice. 30mph to 0 in nothing flat. No problems with stalling before yesterday. It's at the shop now, but they tell me they aren't finding anything and probably won't if they can't get it to die on them too. It had only been driven for about 5 minutes before each occurrence, and each time I had just topped a small hill(if that matters). The second time, it did slightly hesitate to restart and seems to me there was some light smoke from the tailend.
View 19 Replies
When I bought my 2008 accent I had to replace the two front tires in order to pass inspection. I think the garage didn't notice that my rear tires were actually a different size. The entire summer season I had been running two 205/45/16's on the front and two 205/55/16's on the rear.
After the winter I took them to a different garage to take off my winters and they refused to put my summers back on.... is this a major issue to run the 205/55/16's on the rear axle and the 205/45/16's on the front axle? I know they fit but is there a real safety concern or the garage covering their own bases.
View 3 Replies
How to remove a crankshaft pulley like this one? It doesn't have any holes for bolts, to hold some soft of breaker bar in place.
Pulley.JPG ....
View 4 Replies