Oldsmobile - Leaks - Cutlassciera :: 1994 V6 Idles Rough And Usually Stalls If Put It In Gear When Start The Engine
May 22, 2013
I have a 94 Oldsmobile Cutlass Ciera, (3.1L V6 GM3100 engine). When I start the engine it idles very rough and usually stalls if I put it in gear. Eventually once it warms up I can drive it, but when I do drive it's extremely sluggish on accelerations and acts like its about to die. At constant speeds it runs mostly ok. We figured it was a vacuum leak, but we've tried every test we can think of to find it and talked to a couple mechanics and tried their tests and it passed all of them. Supposing it isn't a vacuum leak, then what it might be?
View 4 Replies
Advertisement
I have owned this 1989 Cutlas Ciera for nine months. I bought it for commuting, because my truck is a gas guzzler. Two weeks ago, the Ciera began tick tick ticking. It sounded like it was coming from the lifters. I tried the easy fix first, a little auto elixir, which I have never had much faith in, but figured I would try. I put half a bottle of Sea Foam in the oil. The exhaust smoked white for a few minutes and over the next 20 or so miles the ticking quieted some. 100 miles later, the oil was very dirty, and seemed thinned, so I changed the oil.
And, being that I had just topped off the tank, I added the remaining Sea Foam to the fuel, as the bottle informed me could clean fuel injectors. When I next started the Ciera, the lifter tick seemed louder, white smoke poured out of the exhaust and does not seem like it will stop smoking, and the car now stalls in gear. I'm not sure where to start: head gasket, adjust lifters, cam timing belt, could some of these symptoms be caused by the Sea Foam? It may be more economical to junk this car if repairs are costly, but I may be able to do the work myself if parts are responsible and repairs are only moderately difficult.
View 2 Replies
I have an 01 olds alero, I been having problems with the engine stalling out. i was told it may need a new fuel filter so I replaced filter and now it idles rough till it stalls. What to do next? I replaced the plugs 2 years ago also.
View 1 Replies
1996 / 2.2 L4 / 186k / Upper engine rebuild 30k ago
Car was driven on a errand by my mother. Upon trying to leave for home, the car started running very rough, and stalling. From the description she gave on the phone, it sounded like a plugged up exhaust. I told her to get some fresh gas and ease it home after.
When I checked the car for codes, I got 2. A P0300 and a P0122. Okay, so the throttle position switch has taken a dump, that's easy enough. The car has 186k miles, but my constant nannying usually soothes her, so surely that's all, right? God, I wish that turned out to be true.
I pulled the plugs, and #4 was gas fouled and sooty, #2 and #3 looked lean, and #1 was partially wet fouled. There was also gasoline in the oil. When the car would run, it would run the gambit from idling semi rough then stalling out and refusing to restart, almost like it was flooded, to idling scarily bad and no pedal response, to running too high of an idle and idle searching.
Since I have:
Replaced the TPS
Replaced the IAC
Replaced the CTS
Replaced the MAP
Replaced the ICM
Replaced the FPR
Replaced both ignition coils
Replaced plugs and wires
Replaced the fuel injectors
Replaced the PCV
Replaced the fuel filter
Checked the pintle on the EGR (looked good, cleaned)
Checked for Vacuum leaks (as best I could)
Checked the Fuel pressure (40 PSI) (drops to 20 after shutoff)
Checked for exhaust restriction (ran open exhaust manifold)
That brings us to today. New injectors just in, and the engine will run, but rough and loud. It almost sounds like the firing order is off slightly (I am using 1342 or from L to R 4132) and throttle control is almost non existent. It also shuts off when its warm almost like its flooded. No codes are showing. (despite discovering a sensor in back being unplugged and the O2 sensor being unplugged at times).
View 19 Replies
I have a huge problem. My 94 ranger 2.3L 5 speed manual transmission, has problems with idoling while it's cold, has no power going uphill and stalls when I slow down to stop. This is all after putting a new motor in. The old one was running ok with 310,000 but lagging bad. I figured with the driving I do, a new motor wouldn't be a bad thing. Boy, was I wrong. It has been a nightmare. But once the truck is up to operating temperature, it runs so smooth you wouldn't think there was a problem. But let it cool off, restart, and boom! There it is. We have changed so many parts and sensors with absolutely no change to the original problem. It's very frustrating. I just can't let this problem win. I will figure it out.
View 13 Replies
The 93 Cutlass Ciera 3.3 6 cyl. is hard to start..takes like 3 tries to start it...even after changing..oxygen sensor, MAF sensor, coil pack, fuel filter, air filter, good plug wires, crank position sensor, fuel pump, sending unit....if idling low will stall sometimes. Mechanic said it's slow getting spark up just when starting it..not sure why..
View 1 Replies
I have a 1985 Cutlass Ciera Brougham with a 2.5L four. Got in it one day and when I turned the key nothing happened except the dash lights came on. No clicking or buzzing, no engine turning over, nothing... Pulled the starter and had it tested, it passed. Then again it is only about a year old. I then jumped the poles on the starter and the engine came to life. Replaced the ignition switch ( the electrical part ) still have the same problem. Turn the key and nothing happens except the dash lights.
View 8 Replies
i have a 1994 mitsubishi diamante 3.0 sohc hard to start and idles real rough. it has new plugs,wires,cap,rotor button,fuel filter,and air filter.fuel pressure is between 45 and 50psi which is good i have good compression on all cylinders timing belt is good and i am getting spark to all plugs. with the car running i pull the plug wires off and cylinders 1 3 5 makes a difference but 2 4 6 their is no change.the car was setting for two years.it dose have new gas.the check engine light is not on and has no codes.
View 2 Replies
1995 Mazda Protege1.5 LAuto153K miles.
My car was running fine, then one day it started sputtering while driving, mostly when I accelerated. It stalled and I could not get it started. This happened on a day when it was raining hard, but not sure that had anything to do with it. A few days later when I went to pick the car up it started right up, it had stopped raining and been dry for 2 days prior. But about a mile into the drive back home it stalled and I could not get it started.
Here is what I have tested so far.
- Put in new fuel filter.
- Tested the fuel pressure and pressure regulator
- Tested the injectors with a noid light.
- Tested that the spark plugs were producing a spark.
After I pulled the plugs and cleaned and dried them (they were wet with gas) the car started, but I think not because of anything really related to the plugs. What I've noticed is that when cranking the engine if I give it gas it will not start but if I keep off the throttle it will reluctantly start. But once it starts the idle is smooth and as it should be. Then if I give it any gas it immediately stalls. It seems to me given these symptoms that it is getting enough air to idle but not enough air to match the increased gas.
The only CEL code that I'm getting (which I had before this issue occurred) is the "closed throttle position switch" (I forget the number). If it was an MAF, or IAC, or EGR issue would I not get a code? What this could be and how to test it. Again my guess is its an air intake issue but not sure where.
View 11 Replies
I have a 2007 Ford F-150 5.4l v8...
Codes
P0012 int cam position timing over ret bank 1
P0022 int cam position timing over ret bank 2
P0300 random Missfire detected
P0316 engine misfire detected on start up
P0340 cam position sensor curcuit fault
P0345 cmp sensor a circuit problem bank 2
Starts rough, idles rough and stalls occur often when start, after it runs for 5 minutes and sometimes dint starts at all. I replaced spark plugs, coils, cam shaft sensors and had oil changes done and. No effect.
View 8 Replies
I'm driving an 87 v6 auto cutlass 130 000 km on it. Recently changed alternator and battery at mechanic.
After start up i put the car into gear but it wont shift into gear unless I give it a lot of gas and even when I do so it seems to have trouble keeping momentum /staying in gear. The shifts are rough. However after driving for a few minutes there are no issues at all.
It's been quite cold lately and I've noticed that if I let the car run for about 10-15 minutes before driving it's fine, no problems (although this seems a bit excessive).
Could this simply be an old car/cold weather issue or is there something else to consider?
View 19 Replies
2003 7.3 excursion.. The truck starts every time revs up and idles about 3 seconds then the rpms drop and it tries to stall out catches itself then revs backup and idles rough similar to if you have got air in the fuel lines from changing the fuel filter.. About 1 in five times the truck will stall out and it starts and immediately and idles rough but the rpms and everything runs at speed and rpms don't drop again! This is a reman engine/transmission recently installed.. The mechanic who installed it was unable to figure the problem out.
View 6 Replies
Olds Cutlass Ciera, 1990, v-6 engineI warmed-up the engine for about 12 minutes this morning (after 8:30 a.m.), its maximum speed was 20 MPH at 30 RPM when I climbed up the hill to Agri Center from Bonita Lakes area on HW 19. I was afraid to exceed 30 RPM, so I stopped near the top of the hill for about a few minutes. After that, the road is down hill. The engine became vigorous and went beyond 60 MPH at 20 RPM.
View 5 Replies
A week ago, driving home, the tech started to drop quickly to zero then recover, like the ignition was turned off and then back on. I was able to make it home. The car was due a tune up. I replaced the crank position sensor (OEM), replaced sparkplugs (Autolite Iridium), air filter, fuel filter, no luck. I ohmed the coil packs, secondary resistance showed good, replaced the ignition control module (aftermarket). After this, engine would stall after it was at temp, could restart, once put in gear it would stall, but I could go in reverse and drive home backwards.
Reinstalled original OEM ignition control module. Towed to GM Dealership, mechanic said fuel pump was bad, ignition wires needed replaced, one injector ohmed bad. I took car home, replaced fuel pump (OEM), ignition wires (OEM), no luck. Removed plenum, found pcv valve clogged, and hose kinked, replaced both, ohmed all 6 injectors, 5 injectors read 12.3 ohms, 1 injector was 11.6. Replaced all 6 injectors, (Napa), plenum gasket, still same problem.
GM dealership said computer said no data, they though perhaps ignition control module was bad, but I don't think so. I hooked up my Actron shorting plug, reads code 12 which means no faults, no other codes. I noticed EGR valve has a lot of carbon in the hole, thought about changing it, but I'm really not sure where to go now. The car is a 1994 Chevy Lumina with 230,000 miles, spent about $500 the last week doing brakes, and trying to fix this engine. Where to go from here.
View 5 Replies
I don't know what is wrong with this car, I have put in new titanium plugs, new plug wires, new fuel filter, new air filter, changed the oil, I burn mid-grade gas. The car starts right up when cold, however once it warms up it idles on a non regular number, dies when driving and is very hard to start. I get lousy mileage and it smells like it is either not getting enough gas or not getting enough air. I don't know what else to do. I had it analyzed with an electric analyzer, no codes were found. When the plugs were put in the air flow sensor had either gas or oil on it. It does not use any oil.
View 1 Replies
My gti with 5k miles will be in the dealership 3weeks on Monday! No one has been able to diagnose the problem! I called VW corporate and they told me that the dealer was working with their tech support and engineers.
The problem is has really rough idle were it stalls out. Bank 1 and Bank 4 are misfiring. This is the part were they are stuck. Once they remove the oil cap the car runs perfect! It stops all misfires and idles perfect. They've ran smoke test, compression test, vacuum test. Replaced pcv, high flow fuel pump, intake manifold.
View 16 Replies
My 94 850 turbo wagon starts rough and idles very high. the rpms dont come down. After turning car off, wont restart again unless I let in sit for a while.
View 11 Replies
When I turn-on AC or defroster, motor idles rough then stalls. My mechanic says it is not related to CHECK ENGINE light or exhaust O2 sensor? I have an 02 Ford Explorer.
View 4 Replies
I just replaced the water pump and put it all back together, now it won't run well enough to drive. Checked vacuum system, all sensor connections, hoses, gas cap, changed fuel filter, I can hear the fuel pump kick in, reset system with battery disconnected and have looked at everything I can think of so far.
Now - starts fine, idles about 10 seconds and then begins to idle rough and dies. If I use the throttle I can often keep the idle up, but then backfires or acts like no fuel and again dies. Used fuel cleaner and made sure there was plenty fuel in tank.
I am looking at replacing sensors at this point but which one first?? They get a bit expensive real quick.
View 5 Replies
2002 f150 4.6l v8... Truck is misfiring and the exhaust is smelling very rich, I have new coils and plugs, it also idles rough and stalls if i let it idle for more than a couple minutes. Could it be something with fuel delivery system?
View 1 Replies
My 1994 Silverado 1500 has been running rough, chugging, smelling gassy and sometimes quitting while idling. We replaced the plugs and wires. This didn't actually work, but while testing it, it started to overheat. We added water and the water squirts out everywhere from the bottom of the engine. So there are 2 problems...
View 1 Replies
