Oldsmobile - Cutlassciera :: 1989 - Smokes White / Noisy Lifter And Stalls In Gear
Oct 23, 2011
I have owned this 1989 Cutlas Ciera for nine months. I bought it for commuting, because my truck is a gas guzzler. Two weeks ago, the Ciera began tick tick ticking. It sounded like it was coming from the lifters. I tried the easy fix first, a little auto elixir, which I have never had much faith in, but figured I would try. I put half a bottle of Sea Foam in the oil. The exhaust smoked white for a few minutes and over the next 20 or so miles the ticking quieted some. 100 miles later, the oil was very dirty, and seemed thinned, so I changed the oil.
And, being that I had just topped off the tank, I added the remaining Sea Foam to the fuel, as the bottle informed me could clean fuel injectors. When I next started the Ciera, the lifter tick seemed louder, white smoke poured out of the exhaust and does not seem like it will stop smoking, and the car now stalls in gear. I'm not sure where to start: head gasket, adjust lifters, cam timing belt, could some of these symptoms be caused by the Sea Foam? It may be more economical to junk this car if repairs are costly, but I may be able to do the work myself if parts are responsible and repairs are only moderately difficult.
View 2 Replies
Advertisement
I have a 94 Oldsmobile Cutlass Ciera, (3.1L V6 GM3100 engine). When I start the engine it idles very rough and usually stalls if I put it in gear. Eventually once it warms up I can drive it, but when I do drive it's extremely sluggish on accelerations and acts like its about to die. At constant speeds it runs mostly ok. We figured it was a vacuum leak, but we've tried every test we can think of to find it and talked to a couple mechanics and tried their tests and it passed all of them. Supposing it isn't a vacuum leak, then what it might be?
View 4 Replies
Olds Cutlass Ciera, 1990, v-6 engineI warmed-up the engine for about 12 minutes this morning (after 8:30 a.m.), its maximum speed was 20 MPH at 30 RPM when I climbed up the hill to Agri Center from Bonita Lakes area on HW 19. I was afraid to exceed 30 RPM, so I stopped near the top of the hill for about a few minutes. After that, the road is down hill. The engine became vigorous and went beyond 60 MPH at 20 RPM.
View 5 Replies
1996 / 2.2 L4 / 186k / Upper engine rebuild 30k ago
Car was driven on a errand by my mother. Upon trying to leave for home, the car started running very rough, and stalling. From the description she gave on the phone, it sounded like a plugged up exhaust. I told her to get some fresh gas and ease it home after.
When I checked the car for codes, I got 2. A P0300 and a P0122. Okay, so the throttle position switch has taken a dump, that's easy enough. The car has 186k miles, but my constant nannying usually soothes her, so surely that's all, right? God, I wish that turned out to be true.
I pulled the plugs, and #4 was gas fouled and sooty, #2 and #3 looked lean, and #1 was partially wet fouled. There was also gasoline in the oil. When the car would run, it would run the gambit from idling semi rough then stalling out and refusing to restart, almost like it was flooded, to idling scarily bad and no pedal response, to running too high of an idle and idle searching.
Since I have:
Replaced the TPS
Replaced the IAC
Replaced the CTS
Replaced the MAP
Replaced the ICM
Replaced the FPR
Replaced both ignition coils
Replaced plugs and wires
Replaced the fuel injectors
Replaced the PCV
Replaced the fuel filter
Checked the pintle on the EGR (looked good, cleaned)
Checked for Vacuum leaks (as best I could)
Checked the Fuel pressure (40 PSI) (drops to 20 after shutoff)
Checked for exhaust restriction (ran open exhaust manifold)
That brings us to today. New injectors just in, and the engine will run, but rough and loud. It almost sounds like the firing order is off slightly (I am using 1342 or from L to R 4132) and throttle control is almost non existent. It also shuts off when its warm almost like its flooded. No codes are showing. (despite discovering a sensor in back being unplugged and the O2 sensor being unplugged at times).
View 19 Replies
I have a 1985 Cutlass Ciera Brougham with a 2.5L four. Got in it one day and when I turned the key nothing happened except the dash lights came on. No clicking or buzzing, no engine turning over, nothing... Pulled the starter and had it tested, it passed. Then again it is only about a year old. I then jumped the poles on the starter and the engine came to life. Replaced the ignition switch ( the electrical part ) still have the same problem. Turn the key and nothing happens except the dash lights.
View 8 Replies
The 93 Cutlass Ciera 3.3 6 cyl. is hard to start..takes like 3 tries to start it...even after changing..oxygen sensor, MAF sensor, coil pack, fuel filter, air filter, good plug wires, crank position sensor, fuel pump, sending unit....if idling low will stall sometimes. Mechanic said it's slow getting spark up just when starting it..not sure why..
View 1 Replies
My truck is puffing smoke after about 10 minutes and warmed up (looks white). It happens only one time for about 30 seconds and looks light grey or whitish in color, definitely not black smoke. The truck runs just fine, starts great, doesn't hesitate or studder, doesn't loose any coolant, no signs of pukage. In other words, it Runs perfect.
By the time the smoke happens I am usually at an intersection and see this white smoke billow past me or see it in the pass. side mirror. it's too hard at the time to get out of the truck at that exact 10-15 seconds it smokes to smell it or see it's true color without my sunglasses on but it looks white or greyish. not convinced it's a blueish color.
The truck doesn't smoke at start up or run rough so I'm ruling out injectors. I think it might be the egr cooler that is still connected eventhough there is no hot gasses going through it. (Did the up pipe mod). I might have an egr valve that has a bad seal on it. I'll have to remove the egr valve and see if it looks gummy in there since the egr cooler still routes coolant.
The other thing it might be is a bad oil seal on the turbo which is burning off leaked oil after it's warmed up, again I don't see it smoke for the rest of the day.
The very first time I saw it smoke was the day after I did the up pipe mod and capped off the egr cooler. I may have had a small cooler leak before I did the up pipe mod and now the coolant (if it's coolant) can't run in the exhaust or burn off there directly. My SCT turns off the egr valve but the valve may have a bad seal in it along with a defective egr cooler. will remove the valve to inspect tomorrow if possible.
View 14 Replies
I have 05 F250 SD with 150k on it. The engine has the typical cam phaser knock, timing chain slap on start up and occasionally have a noisy lifter. As long as I use fresh 20-40 oil the engine symptoms are less and the engine runs strong. The motor also doesn't leak or burn oil and the plugs were change out about 20k ago.
The truck is still good and is prefect for my needs so to me it's seems worth fixing the needed repairs. What I would like to figure out how far should I take the motor... just have the chains, guides and phasers replaced or buy a rebuilt motor and swap it? I'm thinking just doing the phases and etc would be 1/2 the cost but may not last as long as rebuilt motor. But realistically I might only put 5-7k miles are year on it anyways.
View 14 Replies
ok so about a year ago and 7 thousand miles ago (abouts) I did a engine build and rebuild I had brand new injector cups, injectors (180/100's) and new o-rings......now I've got fuel in my coolant and smokes like a freight train in the mornings white/grey I believe (its dark) but never black smoke but not the smell of coolant like unburnt fuel truck starts up amazing at 10 degrees' when I had the machine shop building my heads for my stg 1 cam I had told them not to install my cups well they did anyways and used red locktite when I keep hearing and seeing recommended to use green and have used green in the past
I know most situations are cracked cup, cracked heads, my biggest question is ya think the red locktite will hold? And since the cups are new could it be a injector o-ring? dosent the fluids on the injector go botton to top (coolant-fuel-oil) and a bad oring mixing the two I did notice my fuel psi was sittin higher liker 75 psi iv lowerd it since then
View 11 Replies
I have a 64 Olds Cutlass. I drive it once a week or so. That means it sits most of the time. Lately it's been very damp and rainy. I've noticed that when I start the Olds up there is white smoke coming from the exhaust. This lasts about a minute or until the car warms up and I start driving. Then it disappears. Is this just condensation burning off or, I hope not, a blown head gasket? How can I tell the difference?
View 2 Replies
My 2000 alero was WAY low on oil so I added a quart then drove for about 45 mins at 40 mph the car seemed fine. the following morning when I went to start it the car turned over but would not start when it finally started the engine knocks and it is putting out a lot of white exhaust. obviously I need to see a mechanic but what might be wrong. my neighbor said one of the cylinders isn't doing what ever it is supposed to do he said it passed a compression test but I don't know what that means...
View 3 Replies
I have 93 cutlass Cierra..6 cylinder..3.3.. when it's fully warmed up it stalls out on me as I'm accelerating from a stop. but then if I wait a minute and re start it it most times will run ok.. and is loosing power sometimes, when fully warmed up she gets bogged down in pressing the accelerator....it won't stall when Idling.. only when fully warmed up when Accelerating....the engine raced the other day as if someone was stepping on the gas when I wasn't.. Only did that once..hasn't did that since.. Service engine light is on..I have new Oxygen sensor, cleaned the maf sensor..new fuel pump and new fuel filter..new plugs and wires and air filter this past summer..
View 4 Replies
2001 Oldsmobile Alero, 4cyl, purchased in March with around 150k miles.About a month and a half ago I topped off the coolant. 2-3 weeks ago I noticed the exhaust was intermittently throwing off white smoke. Not thick, opaque plumes or anything, but more like how your exhaust might look on a cold day. Being May though, I knew the temperature was not responsible.
This white smoke would occur intermittently and usually stop after driving for a a little bit. Since the white smoke was not constant and the coolant levels seemed to be okay I figured maybe it was something with the EVAP system or the fuel mixture. On a hunch and as a matter of maintenance I put in new Oxygen sensors a few days ago. The next day my coolant light went off again. Since then I've put radiator stop-leak in the coolant and some STP "gasket rejuvenator" in the oil.
My theory: if the head gasket is indeed cracked, it's a very small crack--small enough so that after the engine warms up a bit the gasket expands essentially sealing the crack. This would explain the intermittent nature of the white smoke and and slowness of coolant leak. Are there any other tell-tale signs I should look for with a bad gasket, if this indeed that case? I saw in the store some stuff similar to stop-leak specifically designed for sealing head gaskets that involved draining the radiator, dumping this stuff in and running the engine for a bit, draining it out, and letting the car sit for a day before putting new coolant in. If the head gasket is the issue would the combination of stop leak.
View 2 Replies
My 1989 Honda Accord LX, with 135,000 miles on it, stalls after a few minutes of driving. Then, after re-starting, it stalls before I even have a chance to put it into drive. My mechanic replaced an electric base plate gasket in the carburetor but warned me that this repair might not fix the problem. If it didn't, I probably would need to replace the carburetor -- if one could be found for a 1989 model. Well, I still have the problem. My question: Is it worth it to invest $1,500, more or less, for a carburetor for a 22-year-old car? I've been using it strictly as a second car for the last 11 or 12 years. It seems to be in good shape otherwise.
View 2 Replies
3 mechanics can't find what is wrong but when I come to a stop sign or light my car stalls, not every time but a lot. Also, seems to happen more in cold or wet weather. So every time I stop and idle I have to quick put it into park.
View 2 Replies
1997 Olds. Bravada. 4.3L original engine. 217000 miles, maintained well (routine oil changes, fluid checks, etc)
Intermittent stalls. When stalling, voltage found to drop to 0 even though radio, headlights, and dash lights remain functional. Engine will sometimes "automatically" return to running (it doesn't turn over, just runs) and the air bag light flashes, other times it needs to be restarted. No problem restarting, but may or may not stall a few seconds later. No specific action triggers the events. On a potential side note, the rear wiper motor will spontaneously start running occasionally (once per week frequency typical).
Attempted fix: cleaned both battery contacts, removed and cleaned frame ground, removed and cleaned body ground, all done with either sand paper and/or a wire brush
View 1 Replies
Have a '92 Olds Cutlass Ciera 6 cyl 3300 engine. After 20-30 mins of driving it dies when I have to stop for a light. Depressing the brake kills the engine. Starts right up after but as soon as I put it in drive, it dies. If the car sits for 20 mins or so after problem begins it's okay. If I get to an intersection and have to stop, I put it in neutral. When I have to go again I rev the engine, let it die down some and then put it in drive (hard on the car, I know, but it's only way to get going again. Once I'm moving, I can accelerate and it's okay. What is wrong with my car?
View 3 Replies
I have an 01 olds alero, I been having problems with the engine stalling out. i was told it may need a new fuel filter so I replaced filter and now it idles rough till it stalls. What to do next? I replaced the plugs 2 years ago also.
View 1 Replies
I drive a 1995 olds Supreme 3.1 that has 125,000 miles. It runs like a dream but I have been having one problem I cannot pinpoint a solution for. When started cold, it runs and drives perfectly all day long, no problem. However once it reaches operating temperature and is shut off for a short period of time, it shudders and stalls upon restart. Then it does not restart until the engine is cool. The problem has been intermittent and not as much of an issue during the winter, but as spring approaches I worry it may become a bigger problem.
It has had a recent tune up: new spark plugs, wires, radiator, hoses, fuel filter, fuel pump, air filter, and water pump. This issue existed before all these parts were replaced.
View 2 Replies
I have a 89 F150 4x4 lariat with the 302 8cyl and dual gas tanks. I was driving to work and the truck died. I have spark and enough juice to turn it over so I must be getting no fuel. When I turn the key to the on position I do not hear the fuel pump whine as it primes, it's dead silent. I'm assuming the fuel pump is dead.
Are there any fuses to check? I did check the switch that goes off when in an impact and it was not tripped off so it's not the problem.
My hayes manual (which i find is wrong ALOT) says that 87-89 f150's have a single fuel pump that is external to the tanks and found along the left frame rail? Can anyone confirm? Someone told me they thought it might have 2 pumps but I switched tanks and the truck still didn't start (or make a fuel pump sound) so unless the planets aligned and BOTH pumps blew simultaneously I would assume there's only 1 pump.
View 14 Replies
My 88 "Rosie" has been having problems for months. It hesitates, stalls, and sometimes backfires. This is an intermittent problem, though it is happening more often lately. I took it to local auto shop and their computer showed Rosie was throwing a misfire code as well as a lean code. I took it 3 months ago, and I took it last week, got the same codes. The lean code led me to check the fuel pressure. I did and while it should be healthy 48-55 psi, I got 48 for awhile then 15 PSI! Now I'm thinking fuel delivery. I started with the filter. Sure enough it was dirty. Weeks later, the problem persists. I replaced the fuel regulator (ok, mostly because it was cheaper than the replacing the fuel pump, which I really didn't want to have to do.) Still, no luck, so I finally caved and spent $200 and 12 hrs dropping the tank to replace the fuel pump. Guess, what? Still no dice. I'm still getting the hesitation and the misfiring. I haven't put the fuel pressure tester back on it (been busy) so I don't know if the pressure is still low or if these other things are even related. I thought my logic was infallible. Let's face it, there's a finite number of parts that control fuel pressure. I'm running out of parts to replace. Where did I go wrong? The only thing I can think of that could still do it is perhaps the fuel pump relay? I dunno. Would it work off and on or fail completely? I'd love to get some opinions on this.
View 19 Replies
