I have an 01 olds alero, I been having problems with the engine stalling out. i was told it may need a new fuel filter so I replaced filter and now it idles rough till it stalls. What to do next? I replaced the plugs 2 years ago also.
View 1 RepliesI have a 94 Oldsmobile Cutlass Ciera, (3.1L V6 GM3100 engine). When I start the engine it idles very rough and usually stalls if I put it in gear. Eventually once it warms up I can drive it, but when I do drive it's extremely sluggish on accelerations and acts like its about to die. At constant speeds it runs mostly ok. We figured it was a vacuum leak, but we've tried every test we can think of to find it and talked to a couple mechanics and tried their tests and it passed all of them. Supposing it isn't a vacuum leak, then what it might be?
View 4 RepliesMy 2001 alero 3400 engine is getting hot again this alero is running with a 2001 impala engine run great for few months, replace radiator, hoses, thermostat and suddenly coolant start leaking in the overflow, fans not working even with ac on, i replace the etc sensor and did not work, the fans turn on when I disconnect the etc sensor so i think the fan motors are ok. I got one pcm module from the salvage yard in case I need to replace it but I read that only the dealer can reprogram the computer system because vin number issues....
View 2 RepliesQuick back story I bought a 1999 Ford Ranger It is a 4 cyl with an auto trans the guy said it had some trouble with the tranny (major understatement) he also forgot to mention he cut out the CAT. so running a 4 banger off the header.
When you start the truck it rough idles but you have to hold the gas down til it warms up. You can shift into reverse but it labors the motor and the motor will not up the rpms kinda stays at idle and wants to die no matter how hard you accelerate and you can't move up a slight incline.
When you shift into drive you have to rev the motor to 3 grand an it will catch then move slowly forward. no matter how high the revs go. The fluid levels are a tad above the full level and a bit dark for my liking.
Ok, I used an OBDII scan tool from the parts store and it came up with 3 codes P0351, P0352, P0500. From my internet search the first two seem to be coil related which explains why the motor is running like garbage. The last may or may not have to do with what the tranny is doing.
My 2001 Oldsmobile Alero only starts about 50% of the time and has also turned off twice when I was driving, once in a parking lot and once when I was stopped at an intersection. It cranks and the radio and lights work. The fuel pump was replaced two years ago and sometimes you can hear the pump turn on and sometimes you can't. My husband replaced the fuel pressure regulator and has switched out the fuel pump relay but it hasn't fixed the problem. Based on this, can you tell whether the fuel pump might need to be replaced again or whether it could be something else connected to the fuel pump, or something else entirely? The fuel pump is under warranty at the dealership that replaced it, but unless the fuel pump is bad then I don't want to go back to this dealership and would rather go to different repair shop.
View 1 RepliesI have an 01 Alero that is a great little car with only 80k on it. Runs and drives like a champ but it has 2 issues that drive me nuts. The AC doesn't work at all. If you press the button on the dash, it does not light up. The compressor doesn't do anything either. I did check all the fuses trying to eliminate the simple but I didn't find any bad ones. What would be my next thing to check? Is it ever the AC relay?
Then the one that really frustrates me: the rear defrost. I live in MI, so 75% of the morning I need it to clear either snow, ice or fog. The button works but the lines don't heat up. I checked them all for power and none have power. I also checked each one for breakage and continuity and they are fine. I saw somewhere that the connection at the module likes to fry but I inspected it and didn't see anything burned.
2001 Olds Alero. i'm getting a P0300 reading, Cylinder misfire, and i was told a could months ago my mass air flow sensor was out of range. are they related? how serious is a misfire? can i drive a couple hundred miles before service?
View 2 RepliesI have an '01 gti glx that I just swapped a motor into. I got the motor out of an '01 jetta glx, exact match AFP engine code.
I get cylinder 2 misfires mostly (high number) but I also get 5 and 6 intermittently as well as a P0300 code.
Sometimes I also need to hold the gas down just to get it to start even after the crank sensor.
The engine idles sometimes at 600 rpm but drops and nearly stalls after revving at all.
What I've tried so far:
working cam sensor from my old vr
brand new crank sensor
brand ned wires/plugs
new fuel filter
swapped injectors of misfiring cylinders from old motor
lined up the timing 3 times now and its still perfect
I know the coil pack works because it was on my old motor, which ran fine, just leaked oil.
I don't know what is wrong with this car, I have put in new titanium plugs, new plug wires, new fuel filter, new air filter, changed the oil, I burn mid-grade gas. The car starts right up when cold, however once it warms up it idles on a non regular number, dies when driving and is very hard to start. I get lousy mileage and it smells like it is either not getting enough gas or not getting enough air. I don't know what else to do. I had it analyzed with an electric analyzer, no codes were found. When the plugs were put in the air flow sensor had either gas or oil on it. It does not use any oil.
View 1 RepliesHaving some issues with my 2003 Alero 4 cylinder. Upon start the entire engine shudders and the check engine light flashes. I have to turn it off and turn it on and it will stop most of the time. I've taken it in and the mechanics can't get it to reproduce the same issue for them. Just replaced all four plugs, boots, ignition coil.
View 1 Replies2001 Oldsmobile Alero, 4cyl, purchased in March with around 150k miles.About a month and a half ago I topped off the coolant. 2-3 weeks ago I noticed the exhaust was intermittently throwing off white smoke. Not thick, opaque plumes or anything, but more like how your exhaust might look on a cold day. Being May though, I knew the temperature was not responsible.
This white smoke would occur intermittently and usually stop after driving for a a little bit. Since the white smoke was not constant and the coolant levels seemed to be okay I figured maybe it was something with the EVAP system or the fuel mixture. On a hunch and as a matter of maintenance I put in new Oxygen sensors a few days ago. The next day my coolant light went off again. Since then I've put radiator stop-leak in the coolant and some STP "gasket rejuvenator" in the oil.
My theory: if the head gasket is indeed cracked, it's a very small crack--small enough so that after the engine warms up a bit the gasket expands essentially sealing the crack. This would explain the intermittent nature of the white smoke and and slowness of coolant leak. Are there any other tell-tale signs I should look for with a bad gasket, if this indeed that case? I saw in the store some stuff similar to stop-leak specifically designed for sealing head gaskets that involved draining the radiator, dumping this stuff in and running the engine for a bit, draining it out, and letting the car sit for a day before putting new coolant in. If the head gasket is the issue would the combination of stop leak.
My mom's 2003 Alero has had a bad catalytic converter for the last few years.. at least that's what she was told when she took it to the shop. The engine light (P0420 threshold below efficiency) has been on over the last few years and I occasionally check it with a code reader to make sure no other codes have been added. Up until today - as far as I know - none have been. Now today when she was driving it the engine light started flashing and running rough and making a knocking sound.She brought it straight home and I hooked my scan tool up and it gave the same cat code as I just mentioned, plus a P0306 misfire code. So I pulled the plug wire on number six cylinder and hooked up a spark tester to it - and it showed a decent spark. And to verify the spark being normal, I tested at another plug wire and the spark looked about the same..so I don't think anything is wrong with number 6 plug wire or coil or anything like that but am not sure. Also, the spark plugs were replaced a couple of weeks ago because the ones in the car were worn down about .010''. I can't imagine this having anything to do with the misfire because I did them myself and made sure they were gaped properly and that all the wires were put back on the correct plug/cylinder and plus it ran fine after the plugs were installed - but thought I would mention it anyways. And I was very careful not to damage the platinum on the plug when gaping them.
Did a little bit of research and found this: A code P0306 may mean that one or more of the following has happened: Faulty spark plug or wire Faulty coil (pack) Faulty oxygen sensor(s) Faulty fuel injector Burned exhaust valve Faulty catalytic converter(s) Running out of fuel Poor compression Defective computer
Car Details: 2004 Olds Alero GL, 250K miles, well maintained.
Our car recently started shuddering/vibrating at speeds over 45mph. Once the shudder begins, it continues for the remainder of the drive. It doesn't feel like it's in the wheels or the steering column, and there are no warning lights on the dash. It seems to be more intense when braking, as if something were fighting the inertia of the vehicle. There's no difference in the sensation when driving around corners.
After a few minutes of driving, there seems to be a burning rubber smell that is concentrated near the windshield in front of the driver's seat. I suspect that something is damaging a hose with heat or friction. I'll be taking it in to a mechanic.
My 2000 alero was WAY low on oil so I added a quart then drove for about 45 mins at 40 mph the car seemed fine. the following morning when I went to start it the car turned over but would not start when it finally started the engine knocks and it is putting out a lot of white exhaust. obviously I need to see a mechanic but what might be wrong. my neighbor said one of the cylinders isn't doing what ever it is supposed to do he said it passed a compression test but I don't know what that means...
View 3 RepliesAfter I start up and drive my jeep around town and then shut the engin off. Then I get back inside the jeep, start it up the engin idels rough. Some times the engin light comes on. I had a coil pack installed and still the same symptoms. What do you think?
View 2 RepliesLately I have been having some trouble with 2002 Oldsmobile Alero v6. When the car is sitting in park I have noticed that the engine idles roughly, And when I try to drive it, the car hesitates on the acceleration every now and then. Also the emissions light (the orange one) will come on for awhile and then dissapear. At first I though it was dirty fuel injectors so I added some Fuel injector cleaner, but that has not fixed the problem. I was thinking the park plugs may need replacing?
View 1 RepliesMy gti with 5k miles will be in the dealership 3weeks on Monday! No one has been able to diagnose the problem! I called VW corporate and they told me that the dealer was working with their tech support and engineers.
The problem is has really rough idle were it stalls out. Bank 1 and Bank 4 are misfiring. This is the part were they are stuck. Once they remove the oil cap the car runs perfect! It stops all misfires and idles perfect. They've ran smoke test, compression test, vacuum test. Replaced pcv, high flow fuel pump, intake manifold.
When I turn-on AC or defroster, motor idles rough then stalls. My mechanic says it is not related to CHECK ENGINE light or exhaust O2 sensor? I have an 02 Ford Explorer.
View 4 Replies1995 Mazda Protege1.5 LAuto153K miles.
My car was running fine, then one day it started sputtering while driving, mostly when I accelerated. It stalled and I could not get it started. This happened on a day when it was raining hard, but not sure that had anything to do with it. A few days later when I went to pick the car up it started right up, it had stopped raining and been dry for 2 days prior. But about a mile into the drive back home it stalled and I could not get it started.
Here is what I have tested so far.
- Put in new fuel filter.
- Tested the fuel pressure and pressure regulator
- Tested the injectors with a noid light.
- Tested that the spark plugs were producing a spark.
After I pulled the plugs and cleaned and dried them (they were wet with gas) the car started, but I think not because of anything really related to the plugs. What I've noticed is that when cranking the engine if I give it gas it will not start but if I keep off the throttle it will reluctantly start. But once it starts the idle is smooth and as it should be. Then if I give it any gas it immediately stalls. It seems to me given these symptoms that it is getting enough air to idle but not enough air to match the increased gas.
The only CEL code that I'm getting (which I had before this issue occurred) is the "closed throttle position switch" (I forget the number). If it was an MAF, or IAC, or EGR issue would I not get a code? What this could be and how to test it. Again my guess is its an air intake issue but not sure where.
I have a 2007 Ford F-150 5.4l v8...
Codes
P0012 int cam position timing over ret bank 1
P0022 int cam position timing over ret bank 2
P0300 random Missfire detected
P0316 engine misfire detected on start up
P0340 cam position sensor curcuit fault
P0345 cmp sensor a circuit problem bank 2
Starts rough, idles rough and stalls occur often when start, after it runs for 5 minutes and sometimes dint starts at all. I replaced spark plugs, coils, cam shaft sensors and had oil changes done and. No effect.
Starts fine. Runs fine till warmed up. Then dies at idle and runs rough on gear till 1000 rpm. Has only coded iac when unplugged. But would idle with it unplugged. I replaced it. Also got crank can code once while checking it ...
2001 dodge ram 1500 318 engine ....