Nissan - Pickup :: 1993 - Accelerator Pedal Occasionally Sticks
Mar 23, 2013
The accelerator pedal on my 1993 Nissan pickup occassionally "sticks". Mainly when I'm leaving a (stop-sign/red light, etc) or if I let off pedal (in traffic etc) then push on it again to accelerate. I've changed the throttle cable (had a brand new one from brother in law...still in packing). I took it to Nissan dealership few years ago and they couldn't figure it out, same with a (highly recommended) local shop.
View 7 Replies
Advertisement
2005 Magnum with 64K and original battery: Battery warning light turned on and went immediately to battery shop. Alternator checked out ok but battery dead. Battery replaced but upon starting the engine max raced. turned on off several times still races at high RPM.
Since I was out of town, drove home by feathering accelerator pedal by pulling it back with my foot and brake and cruised at about 40 MPH. Got home safe. Will the computer reset after a fixed number of turn ons and offs or must it be taken to dealer for computer reset?
View 2 Replies
Intermittent problem: put car in park and key will turn to off position but not "lock" and therefore cannot be removed. Subaru specialist could not replicate problem, Theories include need a new factory cut key, dirty console, cylinder/steering column tumbler, solenoid, switch , but we think it is some connection between the shifting into Park. Speedometer was replaced about 2 years ago--possibly jumbled something ??
View 2 Replies
I recently had a new engine and radiator installed in my 1993 toyota pickup. I checked the coolant and oil every day since the install, then drove it 250 miles or so without checking the coolant, and found that all the coolant was gone from the reserve tank, and there was a sludge at the bottom. I don't see any leaks, and the thermometer indicator was normal.
I don't understand where the coolant could have gone, given that it's a totally new motor and new radiator, new hoses. I'm worried about the competence of my mechanic, not noticing a dirty coolant reservoir and maybe messing something else up.
View 16 Replies
A friend is stumped by a problem with his truck, so I thought I might get some insight here. I haven't actually seen the truck, all that follows is from what he described, I'm just the messenger here.
The truck had been running fine on a used engine installed about six months ago. Then he ran it out of gas, it hasn't run properly since. It cranks fine, but won't start. He says it WILL start when spraying starter fluid into the throttle body, but only while the starting fluid is supplied. He also says he disconnected the fuel line somewhere near the engine, cranked the engine, and got good fuel supply (but no fuel pressure gauge reading). He's done some logical things: new fuel pump, fuel filter, spark plugs and wires. No luck. Figuring that he'd sucked something ugly into the injectors, he decided to replace those with no change (yes, I cautioned him about throwing expensive parts at it with no clear reason).
He reasons that he must be getting spark based on the engine running with starter fluid, and there must be fuel based on his test with the open fuel line, so he thinks it's an electronic problem, presumably the signal to the injectors. This is out of my league...and my friend is a carpenter, not a mechanic. If he could get a scanner would this kind of problem register a code?
View 19 Replies
When I turned the key to start my car, I got zero activity from it. No ticking, no lights, nothing. So I tried to do a push start, and the engine wouldn't engage. I took the key out, and suddenly my dome light popped on (though it was dim). I put my key back in and turned it, and dash lights looked normal and at full power, but as soon as I pressed the clutch down and tried to turn the key, everything went dead. I took the key out, put it back in, and turned it, but got nothing.
I pushed my truck up to the top of an incline, and turned the key. All the lights looked normal, so I thought I may be able to push start it. Key was in proper position, clutch was engaged, and gear shift was sitting in first. I got a decent speed, released the clutch... and everything went dead.
I can't decide if it's my starter or my ignition system, though I suppose it could be the wiring, or even something else.
View 9 Replies
I was driving when my 1993 Toyota Pickup's brake and battery light came on simultaneously. As far as I could tell, nothing changed in the way the car was handling, nor any smoke, smells, or sounds. I was about an hour from home, so I continued on my way. After about half an hour, the check engine light popped on. I still didn't notice any change in the car.
View 11 Replies
we have a 1986 dodge truck and the brake pedal sticks down and you have to manualy pull it back to release the brake. What could my problem be.
View 2 Replies
For about 6 months my 95 ford ranger 2WD 4 cylinder pick up has occasionally gone into "over drive" when it is not in gear the idle will get crazy high, like one of those party toys that yo blow into and it spins an makes noise. Once put into gear it calms down but it has more forward motion without gas than before. If it gets really bad at stop lights I will turn it off and turn it back on. It may still do it when I turn it back on but by then I will be putting it in gear. When it is in this condition and I turn it off it takes longer to turn off, like it is winding down.
I would say that this happens every 4th time it is drive, sometimes less sometimes more. There seems to be no rhythm. I took it to an electrical specialist and they could not find anything, and last week the check engine light came on so I took it to our normal mechanic. They did a test and found that the engine speed limiter had been reached which was why the check engine light came on and also pretty scary. The diagnostic codes were P0500 and P1270. I am worried 1. that this is making the care unsafe to drive even though it seems like we can manage it to a degree and 2. that is is doing damage to the car by putting it in such a hyper work mode.
View 2 Replies
I have a 95 nissan pickup V6 hardbody and speedometer goes in and out when it is out i just pound on dash and it will work. I took it apart and put white gauges on it and cleaned the connectors with electric spray. Put back together and it's still doing the same thing. But now when I hit dash it dosent work. Check engine light does come on if it don't work. But it did before till I pounded the dash then it went out.
View 1 Replies
have a 1997 nissan pickup 2.4 liter engine check engine light came on code say number 2 cylinder misfiring put in shop. they say that they can't get to misfire.truck run great.just that light keep coming on with code (p o 302)
View 11 Replies
2003 Jetta, 1.8T, 5spd, stock, 129k miles. I am working on a friends car and his complaint is the clutch pedal occasionally sticks to the floor and during this sequence it is hard to shift gears. I removed knee bolsters to inspect under the dash and found all linkage straight, all plastic parts/springs in place and no fluid leaks, I removed slave cylinder from bell housing and found smooth operation and no leaks. I guess I could replace both but I am wondering if there is a common issue. My searches have found broken plastic parts, bent push rods and leaking cylinders.
View 4 Replies
(code p.o.302) number 2 cylinder misfiring. 1997 nissian pickup 2.4 liter automatic. when I take truck out on highway check engine light come on with code p.0.302.when I get back to town. and cut truck off for maybe 20 minute. check engine light go off automatic I do not have to use a scan tool to erase. As long as I am in town light. say off. when I get back on highway check engine light come back on. have had 3 mechanic look at this they can't get it to misfire. they tell me the fuel and spark are doing what they support to do..do you think maybe computer bad. has 255,000 miles
View 5 Replies
My 1999 Toyota Tacoma (Ext Cab, 4x4 TRD) has 162K miles and now the clutch pedal intermittently sticks to the floor. I have to pull it off the floor with my toes while driving and have also felt the pedal start to pull back towards the floor on its own while the truck is in gear.
I'm looking for some wisdom as a few blogs/websites point towards a master cylinder, others say the master and slave, and my local auto shop said I need to replace the entire clutch assembly and throttle bearing. My truck is no spring chicken anymore but I'd like to keep it running for a few more years...
View 6 Replies
Coolant temperature gauge bounce up and down.
View 6 Replies
We have a Nissan Pickup that anytime (in every gear) that the truck reaches 2700 rpm it begins to jerk-feels like you're trying to start it in 3rd gear instead of first. We have had it in a shop with someone who just repairs Nissan's and have been unable to find the problem for over a year. Have looked at the catalytic converter, fuel pump, and air flow meter...nothing has worked...
View 2 Replies
I have a 95 nissan pickup V6. The speedometer stopped working today and engine light came on. truck sat there while I was working and went back out to it. Started truck back up and engine light was still on. As soon as I put it into gear the engine light went off and speedometer started working again. What it could be. It's a 2wd not 4wd
View 7 Replies
I have an 86 Nissan pickup with a z24 motor in it, yes the weird 4 cyl. With 8 plugs. It has been lurching when I let off the throttle or sometimes when I accelerate. Its been doing it for a year and won't do it all the time it is intermittent but does it more then it doesn't.
View 2 Replies
My AC blows cold for a little while, then it blows warm. If I wait and turn it back on the cycle repeats it self. I had the freon filled. Not sure what to do? 1997 nissan pickup....
View 3 Replies
I have a 91 Nissan pick up that is just making a clicking noise upon trying to start it. I replaced the battery. The inside light works, radio works, dash clock works, but still just clicking upon trying to start. Is there a clutch safety switch that could cause this, or starter, or ???
View 8 Replies
1995 pickup truck 2.4 liter 4 cal 4WD. I have a new problem- I drove out to a favorite spot in the mountains (up a dusty road) and when I got to the end of the road my truck was suddenly idling REALLY rough. I was able to drive it home and it runs "OK" as long as you stay on the gas (I say OK but it does want to die and especially wants to die after it warms up and then harder to restart until it cools)- as soon as you let off the gas the idle is on the extreme side of rough. It did not act like a fuel filter has historically (hesitate when giving gas), but I had a filter so I replaced the fuel filter anyway.
I also pulled the air duct work and cleaned it all out, put a new air filter in and used CRC MAF sensor cleaner on the MAF sensor. I did pour in a Chevron fuel system cleaner but it would likely take a tank full at least to work and it does not run good enough to run a tank full through. I put in all new plugs (gapped) and checked resistance on the plug wires and cap- all seems to be acceptable. I checked all the vacuum lines and did replace a couple that were dry and crumbly. I am now at a loss,
View 7 Replies
