Nissan - Maxima :: 2003 - Check Engine Light On / Misfiring
May 5, 2014
I recently bought a 2003 nissan maxima 134k and i bought it with the p0300 check engine light on a looked at the engine and though it was an air box problem because they had previously installed a K&n filter so I went to the junk yard and got a 2000 nissan maxima air box and new filter i changed the oil and checked the spark plugs they look new and the dates on the coils are 2012 and 2013 and still its misfiring. i bought it to a mechanic and he discovered a vacuum tank had previously broke and they glued back together so i replace that with a factory one today same problem still misfiring but it got better but now its a p0306 then i erased the code and p0304 came back i erased it then p0302 came back then i change the cam sensors, and the crankshaft sensor and now it get a p0300.
Symptoms:
*when sitting for a long time HARD TO START ( takes multiple cranks to start it ) but once i leave it off for short time like 30 min it starts right up no problem
* when stop at a stop light in drive i can feel small little explosions sounds like my car is beat boxing
*performance is strong good acceleration no problem on that i just don't want it misfiring
View 14 Replies
Advertisement
I keep failing my emissions because my check engine light keeps coming on. I was told that the problem was the catalytic converter rear and needed to buy one for both sides. The problem I am having that I don;t know which Catalytic Converter I should buy. I know without it is causing my car to stutter. Which I should get?
View 8 Replies
1998 Nissan Maxima had a check engine light come on and started running very rough. I took it to get a code read and came up with P0320 and P0325. I'm not worried about the 0325 since that's a knock sensor. 0320 is a misfire on cylinder 2.
With the car idling, I pulled the power connector from coil pack 2 to see if it made a difference in the idle - nope. I did the same for the other cylinders, and each responded with a noticeable change in the idle, which was remedied when it was reconnected.
I moved the coil pack from #2 to #4 (swapping them) and the same problem existed - idle was rough and didn't make a difference when I pulled the power on 2, but it did on all other coil packs. So, it seems the coil pack ins't the problem since multiple packs don't seem to make 2 work, but they work on other 4 and 6.
I then pulled the spark plug from cylinder 2, it was very black and looked in bad shape. I replaced it. Still no love.
I then put a spare plug in the coil and was able to see spark as the engine ran, so it seems that the coil pack at 2 is getting juice.
So, I have gas (big odor when the car is running - seems super rich) I have spark. Still running very rough and the 0320 code remains.
View 19 Replies
I have a 2002 Nissan Maxima GLE. I had had problems with it misfiring. It said it was misfiring on cylinder 6. Put all new spark plugs on it, same problem. Put new ignition coils, still same problem. Had it checked by several mechanics. NONE of them could find why it wasn't getting power. Then about 2 weeks ago I was driving it home & it died. Got it started & it drove less than a mile & died again. when it died that time, I suddenly had NO POWER to anything in the car. Lights don't work, no horn, no radio, no beeping when key is inserted--NOTHING. if I let it sit for a day or two, it will start clicking & then interior lights will come on--until I put the key in it & turn it over. Then I am back to no power. It does not crank or anything when I turn the key over. I have had the battery checked and they said it is still good, had 100% charge--even after being off the car for over 24 hours. I have been wondering if it is the ignition switch or starter...
View 19 Replies
Okay so I have a 2003 Nissan Maxima 150k and the problem that I'm experiencing is that when the vehicle is in drive my foot on the brake for example at a red light and I have the AC on the engine will begin to stumble similar to a misfire however no check engine light will be displayed if I were to turn the AC off and sit at a red light in here with my foot on the brake the car idles fine and smooth the car currentl drives fine accelerates fine idles fine it's only when I'm stopped with my foot on the brake and the car and in drive with the AC on that the engine stumbles accelerating or cruising any speed above idle with a/c the runs smooth its only at idle and the simple is not predictable it happens often but at random intervals
What I've done so far 1.5 years ago I put in iridium spark plugs Recently cleaned the throttle body its a electronic throttle body Fuel pump and filter were replace in March 2016I tested the alternator put a load on it to see if the engine would stumble but it didn't
My a/C blows cold air and everything in the car works.
View 12 Replies
i have a 2008 maxima with 30000+ miles. its service engine soon light came on recently. i disconnected the battery the light would go off, but would come back on again after a few days. it happened several times now. once i got a code P0011 from autozone while the light was on. the last time the light was on was a week ago and this time the light finally went off by itself yesterday. i took my car to a dealer today. a service advisor told me the reading on his code-reader is NO CODE and the car is fine!. so what have happened and what is wrong with it? could it be serious?
View 4 Replies
I just purchased a 2000 Nissan Maxima GXE with 219,000 miles. I've had it less than two weeks, and the Service Engine Soon light just came on. I live somewhere that requires emissions testing in order to register the vehicle. My temporary plate will expire soon, so I need to get the car to pass emissions.
This is my first Japanese car and first non-American vehicle. I didn't know until after I had given the check to the guy selling the car that he used premium gas. He said that Nissan recommends it. I've never driven a car that required premium gas before and wasn't keen on the idea since here, it is 40¢ a gallon more expensive than regular unleaded.
I spoke with my landlord about it, as he is a certified Honda mechanic. He told me to first try getting half a tank of regular unleaded and putting it in with some fuel injector cleaner. He said if I didn't notice any decrease in performance or knocks, to then just add a bottle of of fuel injector cleaner to every other tank of gas.
I got a half tank of regular unleaded with a bottle of fuel injector cleaner and didn't have any issues. I then filled the tank with regular without any fuel injector cleaner. I used about ¾ of that tank when the service engine soon light came on. I took the car to Valvoline to get the codes read, and while they couldn't give me any code numbers, they said it was something to do with emissions.
Here are my questions:
Is it possible the light came on because I switched from premium to regular unleaded or perhaps because I would need to add fuel injector cleaner to every tank of gas I get and not every other tank as my landlord said he does with his car?
Should I try either adding fuel injector cleaner to every tank of gas or just switch back to premium? If I try either of those, and one of those was the problem, how long would it take for the Service Engine Soon light to turn off?
View 10 Replies
I own a 2003 Nissan Maxima SE with a 6-speed manual transmission. The car has just under 113,000 miles on it. I've religiously maintained the vehicle per the owner's manual and overall it is in excellent condition. In particular, we change the oil on a regular basis per the maintenance schedule. However, on several occasions we have started to hear rattling coming from the engine. The rattling occurs at all engine speeds and in all gears and it doesn't matter whether the car has just been started or if the engine has been running for a while.
When the rattling has gotten more prominent, we've taken the car to the dealership and also to our local oil change place and on both of those occasions, they've told us that the engine oil was VERY low. Also on both of those occasions, we were well within the recommended range in between oil changes (<3000-3500 miles). We have not noticed leaking oil in our driveway or in our garage. I am wondering about the potential reasons why we could be losing oil, and if we aren't seeing any in our driveway where it's going? I've mentioned this to friends and they've said it's 'burning oil' - but we're not noticing any strange smells or smoke. The car is ~10 years old but it's fun to drive and in great condition.
View 4 Replies
I have a 1998 Maxima with 57K miles on it. I just bought it about a month ago. Anyway, a week ago I noticed It felt very "choppy" when I shifted into Drive or Reverse. It felt like it was going to stall but it never did. The Service Engine Soon light has been on for about 3 weeks but now, when I go up hills especially, that light blinks. I can still drive it but I shift into Neutral at stoplights to avoid hearing the rough idle while in Drive. Went to Pep Boys yesterday - they had the car for about an hour and then informed me that they would need to keep the car for a full day because of the "complex issues involved" - especially concerning the codes. The codes they read were:
p0300 random misfire
p0325 knock sensor
p0440 evap emission
My car passed smog test abut 3 months ago. I can drive it OK it just is very choppy and so there's not a lot of power, especially going up hills.
View 1 Replies
My wife has a problem with the check engine light coming on and staying on. The dealer has replaced the fuel pump twice (which they say is the problem) but it keeps happening.
View 4 Replies
I have a 4 cylinder, 2002 Nissan Altima with about 170,000 miles on it. About 2 months ago, the car starting misfiring while driving and the engine light came on. I went to autozone, used their diagnostic tool and it said I needed to replace the fourth cylinder's ignition coil. I ended up just replacing the spark plugs at that point. After replacing the spark plugs, the misfiring seemed to stop, but the check engine light was still on although the car ran great in comparison.
Then, about 2 weeks ago, the car started smelling like gas and slightly misfiring again. I bought set of ignition coils and changed them out. I started it up, the car seemed to work great. I went to the store about an hour later and the car worked better all the way there with no problems. Then, as I was about to leave the store, I started the car up and it started sputtering and misfiring and you could visibly see the engine shaking like crazy when I popped the hood. It stopped shaking, evened itself out, after about a minute. Then, I felt the top each of the coils and the first three were fine, but the fourth had a rapid tapping coming from it that was obviously not right.
I gave it a couple of days, but the car didn't stop smelling like gas or misfiring when starting up, so I pulled out the ignition coils and the spark plugs. The fourth spark plug was brown and burnt from the bottom to the halfway point, unlike the other still-clean spark plugs. My first hopeful thought was, maybe it wasn't tight enough and that was letting gas or oil inside to burn. I tightened it up, put everything back and it seemed to be alright, even the tapping from the coil stopped.
However, within the last couple days, the car has been smelling like gas and feels like it sputters and misfires once I start it up. The misfiring seems to stop after I rev the engine a little bit, but sometimes when I'm idling, you can still smell the gas and sometimes audibly hear a sputtering.
So my question is: what the hell could be wrong? Faulty wires, a stuck valve, bad compression, what? Remember, the fourth cylinder's spark plug was only burnt on the bottom half if that's useful.
View 19 Replies
Yesterday out of no where my rio started to misfire so i immediately took it into autozone to have it checked. when doing so the check engine light was on, but solid.
The tests came back with P0300, P0301, and P0302 or 3. I cant find the papers, but its 3 cyns that are misfiring. The guy at autozone suggested i try changing out the plugs first since its cheaper and has been known to fix this issue.
The second I bought the plugs I went home and changed them out. once finished i started up the car and not only was the car still misfiring, but the check engine light is now flashing... I did notice one thing when changing the plugs.
If facing the engine the second coil from the left had a bit of what looked to be rust. i was able to wipe it off with ease. What my next move should be?
View 9 Replies
The car was misfiring and the check engine light codes were all sensor coils were bad. Lexus told me that it was coil6 bad and they fixed it. I should have had no problems, I got a whole 2 miles and I misfired and engine light back on. I drove for a while and light went off and then misfired again. Before I bring it back in I was looking for some insight. I can't understand how it wasn't fixed right the first time but I don't want to go back and get a few thousand bill either. Could fixing one coil cause another to go bad.
View 1 Replies
i have a 2008 santa fe with a 2.7 61,000 miles 2nd owner ,out of warranty. It started missing and the check engine light came on. I took it to a local parts store who put an analyzer on it an it showed the #3 spark plug was misfiring. I am hoping its the plug. I do my own work but havn`t been able to find a correct sequence to replace the plugs.
View 3 Replies
To start off with I am not car smart! I have a 2008 Santa Fe 3.3L V6. Last year about this time (December) I had problems with the vehicle upon start up would be miss firing and the check engine light would come on. I would turn the vehicle off and restart and it would be fine and not happen again sometimes for a week and sometimes for months. I hooked it up to the computer and found that it was missing on the #6 cylinder. I had the coil pack replaced and that seemed to fix the problem (replaced spring 2011). About a week ago it started doing the same thing (December 1). Upon initial start up when the car is cold and the outside air is very cold it started missing again and having a rough idle. Would turn of the car and restart and would run fine but check engine light would come on.
Hooked it up to the computer once again and it read random misfire. This has happened twice now in two weeks with the same reading each time. Always when it is cold (engine and outside temp) and seems to reset itself when turned off.
I spoke with a mechanic who recently had this same issue with a different vehicle and after trying many things replaced the engine coolant temp sensor and that did the trick. He said it was a cheap start therefore i bought the part and now am looking to replace it. The only problem being i am car dumb and cant find it. I have done many searches and the diagrams i have found don't do me any justice. The past posts on here have given pictures of older models that dont match what i am looking at. It probably is right in front of my face. Any picture of a 2008 that will show the correct area I should be looking at? The vehicle only has about 57,000 miles on it.
View 9 Replies
The ac compressor on my 2003 Maxima keeps going out. Mechanic says the replacements are refurbrished, as the new ones are hard to find and expensive. 143,000 on the car.
View 1 Replies
While driving up a long hill on the highway, one of the cylinders quit firing causing a bad engine vibration and check engine light. I turned around and drove home, pulled the plugs, and found the plug closest to the passenger side had bridged. I'm not sure why; it almost looked like it melted or had some sort of physical damage. This was on a 2013 Sonata Limited 2.0t with 45000 km / 28500 miles.
Pictures here: Spark plug failure - Album on Imgur
View 6 Replies
I have a 1996 ford taurus lx v6 3.0 dohm..my check engine light flashing. then it stop flashing..i did replace spark plug,wires,coil pack..when it start to flash i put it gear the car start to shake and sputter.i really don't know why its doing that the car has about 150000 miles on it..i do get a code p0302 Cylinder #2 Misfire..the new plugs and wires and coil pack is about 2 weeks old..
View 11 Replies
1990 Maxima. Last night the car started shaking after pulling up to stop sign, it kept shaking the whole way home. Acceleration was slow and difficult. Car started up fine this morning, started to shake again at first stop sign...then it was OK for rest of the day.
View 2 Replies
Fix one thing, something else goes wrong. I replaced the resistor or HVAC power module(nissan's term) on my maxima and fixed the problem. Easy job. Put everything back together and now the air bag light blinks constantly when car is running. I did disconnect an electrical connection for easier access to the resistor and plugged back in. I've read, I just need to reset. None of the reset procedures I find on line seem to work.
View 2 Replies
Okay so I recently replace the rear shock absorbers and now every time I take a corner or when I'm going on a surface that's not flat or just if I go over a bump too quick. I here squeaking sounds I replace the shock absorber as well as the strut mount to no avail I've found the noise I've located location of the squeak if where coil meets the mount. I don't want to replace the coil it does look like it might need some replacing the protective metal sheet is gone on the top some of the bare metal is exposed but I would hate to replace the spring and have noise again
Car is a 2003 nissan maxima with 144k ....
View 6 Replies
