Nissan - Altima - Noises - Wheels :: 2003 - Wheel Bearings Going Bad - Fix?
Oct 1, 2011
I THINK my wheel bearings are going on my 2003 Nissan Altima. It has about 95k miles on it and it has been making what I would call a mid-toned rumble or a low pitched rattle (imagine shaking a metal box full of rocks). The noise is coming from the front driver's side. It's more subdued when driving in really wet weather. I am more aware of it when I drive at slower speeds. It doesn't seem to change when I turn the wheel either way, and it definitely gets more pronounced when I go over a bump or a rough patch. I recently had my front rotors and pads replaced, naiively hoped that might fix it - wishful thinking - and stupidly forgot to ask my mechanic about it then. I need to call to schedule a repair, but I would like to be prepared and to know if anything else might make this noise. (and I don't want to jack it up and shake the wheel or anything).Approximately how much does it cost to have this fixed?
View 3 Replies
Advertisement
I have an 97 Altima. When I hit on the brakes, it seems to be okay, but once I let the pedal go, there are clicking noise coming for the front wheels.
View 9 Replies
Two different Subaru dealership repair shops told me that i have loose rear wheel bearings on my 2003 Outback. My car does sound like a VERY loud airplane all the time now, but the noise is the only symptom i have noticed. My shop has told me that they will fix it for a discounted price, but they are not pushing me to get it fixed, and have told me that it shouldn't cause any actual problems besides the loud noise being very annoying. All internet research to the contrary, though. I have to drive about 1000 miles round trip next month -- is it just going to be a noisy trip, or is something horrible going to happen if i don't get the bearings taken care of?
View 12 Replies
I went to a big box store to have new tires put on the rear of my 2002 Nissan Altima. They told me I had a stud broken from the inside of the wheel. The lug nut is still attached, and they can't get the wheel off. Both the stud and the nut turn freely within the socket. Is there any way to get this off without having to pay the $70 a tire place will charge me to fix it? I don't know how long its been like this. I currently have three new tires and one old.
View 2 Replies
I had new tires put on my 2011 Altima around 35,000 miles. I started noticing a hum, so I checked the mechanic notes and they said I had a bent right rear rim. So, I had them replace it immediately. The hum (which only happens specifically at 40mph and at 75 mph) remained so I attributed it to new tires and breaking in.
I took my car to a shop around 45k miles for a check engine light, which ended up being an ECM issue that required a dealer service. I also had him check the tires as the hum was still there. He just rotated the tires and sent me on my way. This is when the steering column started shaking, so I had the dealer check it out and they told me I had a bent rim! Go figure, I've been driving on this thing for about 10k miles.
So, I ordered a new rim and had a local tire place put it on and they showed me the bent rim. Now I thought this would solve things but I was wrong . I still fee the vibration in the steering column at high speeds and the annoying wah hum is still there.
I'm a little lost as to what the problem could be so I'm looking for some insight? Should I start with having the other 3 tires balanced? Could it be that the bent rim caused uneven wearing on my tires over the 10k miles and it may take time to even out? There's no noticeable wear on the tires to my seeing but I could be wrong. These tires are 50k mile tires. Could the bent rim have caused other unseen damage? Keep in mind the wheel they replaced is now on the rear.
I know another cause of shaking could be the rotors but as far as I know they're in good shape and breaking is still smooth. so if they were the issue causing vibration at high speeds I would surely feel it in the breaks.
View 19 Replies
It's Nissan Altima 97. My friend need to take her road test so I let her borrow my car this weekend to do some road practice (I was in the car with her). Besides all the heavy braking, and sudden acceleration. She did alright. Because she is from VT, so she was practicing this VT Turn Around (I have never heard of it before today). She turn the wheel all the way to the right and back up.
I heard a small popping noise, and didn't pay too much attention to it at that moment. However, After she finish that VT Turn Around, we started to driving down the hill, and heard this metal-on-metal noise. It lasted for 10 ft, then went away. The noise is coming from my driver side front wheel. When I got off the car, I found the center of the wheel cover pop off.
(see this link for the pictures) [URL] .......
Now here are my questions. What just happened? and do I need to get it look at immediately, or can I wait until the next oil change?
View 9 Replies
This summer I replaced the inner and outer tie rod ends on a 97 Nissan Altima, had a bent wheel replaced, and had an alignment done. Everything worked smoothly for the last 5,000 or so miles. I had my tires rotated and balanced recently which created a new problem, a shaky steering wheel most noticeable at slow speeds. I've had a similar problem before and had it fixed by balancing the tires. I took it back in to have them rebalanced, thinking they may have forgotten to do it the first time. They rebalanced them and the problem has not changed at all.
View 3 Replies
I've got this 02 Nissan Altima 126,000 miles. I did a front brake job on my self, new rotors and ceramic pads. Immediately after the brake job, I started hearing this horrible grinding noise when weight is shifted to the driver side. It happens when I take apply the brakes or make a right turn. When making a right turn I don't need to apply brakes to hear it. I can sometimes hear it faintly when driving normally.
I took it to my mechanic. He first inspected my brake job, disassembled the rotors and pads, applied brake grease, and reassembled everything. The problem continued. He lifted the car, and had me get in, put it in gear, accelerate, then applied brake, no noise. There is no sign of anything rubbing or grinding in the wheel assembly.
After inspecting the tie rods ends, he replaced the inner and outer on both sides. No Luck. He then replace the ceramic brake pads with regular pads which has reduced the noise but it is still there. I asked around and two other mechanics have suggested the wheel bearings, my mechanic believes this is unlikely.
View 1 Replies
I drive a 1999 Nissan Altima GXE and when i turn the a/c on or turn my steering wheel the car makes a rattling noise towards the belt. I have replaced the belt and i check all the electrical components that are runned on that belt. But i cant figure it out. I think its something to do with my pulley system because my power steering/ac are runned on the same belt along with my alternator and other components. What to check.
View 7 Replies
Question: after replacing rear shocks on 2009 Altima, does in need a rear wheel alignment? After shocks were replaced on my Altima (without wheel alignment), I drove about 4500 miles. After that the tires were rotated and the back tires installed in front. I immediately noticed loud road noise, mechanic says it is uneven tread wear and I think - this is too much of a coincidence. So should they have done the alignment when they replaced the rear shock absorbers or not?
View 6 Replies
I've noticed a creaking sound coming from the left front wheel when I go over a couple of particularly large speed bumps. I have had a lot of problems with the suspension in this car, and have replaced the front struts, the front right control arm, and the sway bar links and bushings. My best guess is that this noise is coming from the front left control arm, as it has not been replaced, although my current mechanic says that the front left control arm is fine. Also, it has been under 10 F here the past few days, so this could also just be a result of the cold weather.
Video of the noise: [URL] ....
View 7 Replies
2003 Nissan Altima 2.5 SL automatic - starts fine when the engine is cold but won't when the engine is hot. It acts flooded. I've changed the camshaft and crankshaft sensors, spark plugs, one spark plug coil, radiator, valve cover and the coolant temperature sensor. The car will turn over but will not start - sometimes it will after 5-10 minutes of trying.
View 1 Replies
I own a 2003 Nissan Altima and I am having trouble switching off my radio since a couple of months. All the other features work except for the power button. As a result, the radio is always on.
View 2 Replies
My 2003 Nissan Altima recently started giving me trouble where I will drive for at least 20 minutes, stop to run an errand, come back, and the engine won't turn over. The first time this happened my check engine light came on. I brought it into the shop and had the cam sensors replaced. I'm still having the same problem. The engine cranks and the battery checked out okay. Car has 93,000 miles on it. I can usually get it to start after 5-10 minutes by cranking and pushing the gas to the floor. Could this be a fuel issue?
View 3 Replies
Had a weird experience with my Nissan Altima (2003) in June that has repeated very occasionally since then. Immediately after starting, there is a single loud thunk. It sounds exactly like a bird flying into the rear left window. In fact, the first time I heard it I thought that's what had happened. Since it has repeated -- although very occasionally, as in a handful of times -- I'm concerned that it's a problem that needs to be addressed. The car has about 100K miles on it and is otherwise in very good condition. What the likely issue might be? (I recently moved to a new area and I don't have a trusted mechanic to ask.)
View 4 Replies
In 30 years of wrenching on cars, I've never encountered this problem. Replaced the pads and left rotor. Rotor is typical Chinese rotor. While there, replaced the wheel bearings. Also knocked out the races (with a brass drift) and replaced the races with the ones that came with the new wheel bearings. The bearings are NAPA bearings. Packed the wheel bearings just like always.
Applied some grease just like always on the spindle. Put it all back together. Tightened the wheel bearing nut while rotating the rotor in the opposite direction. Went to maybe 10 ft lbs. Backed the nut off, set it firm finger tight. Installed the cotter pin. Got a whole bunch of sloppiness in the wheel bearings. I can feel a LOT of it when rotating from the 6 o clock and 12 o clock position. What did I miss? NEVER had this happen before. 2002 f 150 2wd
View 3 Replies
My wife has a problem with the check engine light coming on and staying on. The dealer has replaced the fuel pump twice (which they say is the problem) but it keeps happening.
View 4 Replies
My 2003 Altima (generally trouble-free!) recently lost power ... it would just putter along at 5mph. I parked, and the engine revved up fine. Waited a bit, put in drive and and same issue. I punched the accelerator, it sort of backfired and then ran OK. Next day, I called the local auto center who thought it could be catalytic converter blockage. They ran test for error codes and one stated check engine light was out of order and that instrument cluster should be replaced. They admitted it was bizarre, so I declined the repair and have driven just a handful of miles in the few days since. Today, power lost again, same 5 mph-only issue. I park, turn off engine and wait a bit. Then it wouldn't turn over... some blinking lights in the instrument cluster. So... it's been towed and tomorrow the same auto center will investigate.
View 12 Replies
My right front passenger tire keeps making a loud squealing noise. I've had the brakes and pads changed several times and it keeps making the same noise. I've taken it to the dealer but when they drive it, of course it doesn't make the noise. They checked it and everything seems fine. I took it to another mechanic and they heard the noise as well but can't find any problems. They greased all the gears in the wheel area and it stopped making the noise for a couple of weeks, but then starts right back up again. The car drives perfectly other than that. I'm going to see if I can attach a video file so you can hear the noise. I'm thinking it could be the bearings but everyone that looks at it says they're fine. The noise in the video is much more pronounced now and is a constant sharp squeal.
View 1 Replies
At 20mph my azera sounds like it has bad bearings but they have all been replaced and I still hear the sound. Almost sounds like bad bearing or something in the wheel.
View 9 Replies
I have some whine coming from my front wheel bearings so I'm going to replace them both. I'm not sure if this had been done on my truck before, but I'm thinking so since I have Moog greaseable ball joints.
Truck has 250k miles on it. I'm going to check the pads, rotors and slide pins. Anything else that might need work? I'm sure the half shaft could use a once over, but I don't keep my hubs locked so they don't turn much in regular driving.
View 7 Replies
