Mazda - Mazda5 :: 2007 - Runs Rough - Diminished Power For Climbing Hills
Jan 30, 2013
Our 07 Mazda5 (80k) once in a while will start and run very roughly, and pressing the gas to the floor only gets it to 3,000 rpms.It has diminished power for climbing hills when this occurs. Everytime this happens if we shut the car off and let it sit (between 10 minutes - a couple hours) it starts and runs like a top. We have added drygas 2 of the times, but the last time it happened was on the same tank of gas that we added the drygas to. Check engine light comes on, but will go off after a day or so.
View 5 Replies
Advertisement
We have a 2007 Mazda5 we recently purchased used from a Mazda dealer. We learned later that the car has had numerous repairs the dealer didn't disclose, including a radiator fan replacement and possible new radiator. We noticed that the radiator fan was constantly running, even if the engine wasn't but the key was in the "on" position. The fan shut off when the AC was turned on. We took it to our local dealer for diagnostics who said that wires had been crossed in the original repair, that they connected the wires so that the fan would always run and that we needed a new fan control module.
We tried out a new module but it didn't fix the problem, fan still runs all the time and is very loud. Husband thinks the fan might be blowing in the wrong direction: currently towards the radiator. Another problem, which may or may not be related, is that the AC only works well at high vehicle speeds. When traveling in town, the AC blows very mediocre cool and moist air. According to the original owner, they put in a new AC compressor and a new pressure switch and the AC apparently worked well.
View 1 Replies
Our 2002 Hyundai Elantra is having issues. It shifts fine, no need to double-clutch. It stays in gear. Doesn't grind or anything crazy like that. It does seem like it isn't getting power to the drivetrain, and is having trouble climbing hills. This all came on very suddenly. Hubby thinks it's the clutch -- I think it may be the bushings. Though now, I'm wondering if it's something else? Since it's not having trouble shifting, should we be looking at the fuel system? Sensors? Engine seals?
View 10 Replies
I have a 2000 Ford Explorer with 188,000 miles on it. I bought it used with 110K miles and put a new tranny in at that time. Now, I am having problems. I don't know if it's the tranny or the engine. It looses power when climbing hills. It takes off really slow with no power and finally gets up to speed it switches gears the whole time smoothly but the engine just can't take a load.
The check engine light came on and put out 10 codes:
P1451 EVAP Control System Canister Vent
P1747 Electronic Solenoid A-Short Circuit
P0743-Torque Converter Clutch Circuit Electrical
P0750-Shift Solenoid "A"
P0755-Shift Solenoid "B"
P0760-Shift Solenoid "C"
P0765-Shift Solenoid "D"
P0135-O2 Sensor Heater Circuit
P0155-O2 Sensor Heater Circuit
P1409-EGR Vacuum Regulator Circuit Malfunction
Those are the codes and I don't know how one has anything to do with the other. I checked the dip stick on the tranny and it's clean. Juicy red and not shavings.
View 4 Replies
This problem has been getting worse over the last 2 years. When the car starts it idles fine at about 1000 RPM. As soon as it warms up, it starts to idle rough, between 500 and 750 RPM. It almost quits running. As soon as you give the car some gas it runs just fine. About 3 weeks ago I got a "Engine Lean" check engine light error. I reset the system and have not gotten the error again. Since then I have: changed the MAF cleaned the EGR (made sure it closes completely and ohm out the coils in the actuator) changed the O2 meter on the exhaust manifold cleaned out the throttle body Ohmed out the air idle controller. What I should check next. I was planning to check the fuel pressure in case it is a fuel system problem. It is a 1999 ....
View 5 Replies
I've been driving my 99 ranger 2.5 now for 2 weeks now. Overall I am very impressed and happy with it. Everything seems to be near perfect and in top shape on this truck and I feel like it'll have no problem paying me back.
I've recently noticed, however, that whenever I start up a hill with the climate control on, it shifts from whatever I set it to, to the defrost vents. It returns to the vents I set it to after I crest the hill, and doesn't change vents if I don't drive over hills. I live in a hilly area so that's not convenient. And with summer around the corner, I want this solved.
View 14 Replies
In a recent show a listener described the exact problem I just started to have - the dash hand brake light pops on when i go over bumps or up my driveway . It was a fluid level problem but I don't remember which it was. Was it brake fluid or power steering fluid or something else?
View 4 Replies
03 supercrew 5.4. I've been having problems climbing hills. I'm on a trip and the truck surged fron do then to drive and stopped. Let it sit for 30 mins or so and it was good. Drove another 500 miles ans started again going up some hills. The first time it was 110 out and the 2nd it was 90. I'm pretty sure it's a cop but of course no cel. It does not seem to of over heated either. Can the cops overheat? Do you recommend a diagnostic, will this show up if no cel has show?
View 5 Replies
1997 Hyundai Lantra LS 1.8 5-speed. I live in a really flat area, but we're surrounded by hills and mountains. Whenever I have to go into the mountains I start to get blue smoke from the exhaust after a few minutes of climbing. The longer or steeper the hill, the more smoke I get. Obviously I'm burning oil, but I'm not sure what would cause the problem only when the engine is being taxed.
View 10 Replies
I am having an engine temp issue when climbing steep hills. The gauge goes from normal to the red line but not into the red. The VDC OFF light is on but the CEL is not one. Once I reach the top of the hill the engine begins to cool off and returns to normal. Yesterday I had the radiator flushed and the thermostat changed. Am I looking at a water pump or head gaskets?
View 5 Replies
The car runs fine for several miles/minutes, suddenly the tach starts to climb, up a jump, then up again. This is when the engine starts to run really rough and I pull off the road, let the car cool down and make it the rest of the way to work (about 15 miles).
Here is what I have done: Radiator flush and fill; Oil and filter change; Cleaned EGR and replaced gasket; put in new spark plugs; changed the transmission filter and oil; replaced the O2 upstream and downstream sensors; replaced the thermostat 195 to 180; replace the coolant temp sensor.
The check engine light does not come on (except on start-up check sequence), so it is working. Their are no trouble codes (other than when I removed the downstream O2 sensor to check if I would get errors). The cat converter doesn't glow at night, and doesn't rattle when tapped. The resonator in the exhaust does make a rattling sound, but I don't see why that would be the problem.
I am at my wits end. Any clue what I should try next? The water pump isn't leaking.
View 4 Replies
I bought a '99 MX-5 in the fall with 100000 miles on it. Most of the time it runs fine. But about every two weeks when I go to start it it will run real rough like its only hitting on three cylinders then will eventually smooth out after anywhere from 5 seconds to 2 minutes. But today it wouldn't start at all. Finally started just fine after trying for 15 min. My mechanic changed the EGR valve but it hasn't worked. The check engine lite stays on all the time but when it starts rough the lite will flash.
View 3 Replies
I have a 2002 Nissan Frontier with a non supercharged 3.3L v6. The truck is a crew cab, long bed and 4x4. I have had this truck since I bought it used in 2004 with 26k miles. The truck now has 196k miles and I have done a little modifying to make it a bit more off road capable.
I have done all the work to the truck myself, until last fall when I finally broke down and took it to a dealer, who was not able to find my problem, but I will get to that...First of all, the truck has steel bumpers, a winch, a tool box, onboard air system and large tires, all of which make the little 3.3L work hard. However, for three years since I quit making modifications, the truck ran perfectly cool and the temp needle never once went above the normal operating position, even through thick sand at the beach, mountain trails and towing heavy trailers, until last summer.
Late last summer, on 90+ degree days, I noticed the temp needle would start riding above normal when I had the AC on. It didnt matter if I was on the highway, the city streets or idling in the driveway. When I turned off the AC the needle went back to normal. This started happening occasionally at first (once every 2 weeks) then towards fall it started happening more frequently, almost every 90 degree day. Soon after I noticed the problem, it would happen even with the AC off, but not get quite so hot.
After a few weeks of this, I started chasing the problem. I replaced the radiator cap, the thermostat (tested the old one and tested the new one before installing,) I took the radiator to a rad shop and had it boiled and flow tested, I replaced both coolant temp sensors, and then finally the water pump. When none of those repairs made a difference I built new radiator fan shrouds and that made no difference. At this point I was starting to get discouraged so I borrowed a scan tool from a friend and drove around for a few weeks with it plugged in. I was reading live temperature readings of the coolant and verified that the gauge was working correctly.
The truck ran about 200 degrees with the AC off most of the time, then, when I turned the AC on, no matter if I was sitting in park or driving on the highway, the temp would steadily climb until it got to 222 degrees and I would shut off the truck, at that point the needle was near the danger zone and according to several nissan dealership, the highest normal operating temp is 204, but it should stay around 195. At 205 degrees, the needle would start to move above the normal position, so the gauge seems to be fine. As summer turned into fall, the truck started running cooler as the days began to drop into the 70's. I finally got fed up with chasing my tail and took the truck to a dealer with my main concern being a blown head gasket or cracked head.
The dealership inspected the head and tested the coolant for hydrocarbons and said that the head and gasket are not the issue. They advised that the only other thing it could be is my fan clutch. After that dealership visit, the days were cool so I drove the truck all winter without changing the fan clutch. Then, 2 weeks ago, on a 70 degree day, I hooked up my truck to an empty trailer (maybe 1000lbs) and towed it 15 miles. When towing up hill with the AC on, the temp needle started moving. I immediately went to napa and replaced my fan clutch. Confident that was the issue, I drove the truck to the mountains for a camping trip last weekend. While climbing the hills at 40mph and about 2500 rpm, the temp needle climbed to the near danger zone.
View 19 Replies
Every time I hit a hill, loaded or empty, or get on the truck on level ground after about 15 seconds it acts like it's running out of fuel. The pump starts getting noisy like it has air in it, but it'll straighten out eventually. If you don't let off the fuel it'll eventually stall out. No check engine light, no codes. Truck has a ts chip but it does it on all settings. New fuel filter, changed oil with hot shots secret, new air filter, hutch mod done. I'm at a loss for what to do. Good fuel pressure also.
View 8 Replies
I'm driving a 1995 Mazda Protege with about 200,000 miles. It has been generally pretty reliable, and I have fixed things as necessary, but a DNR has been in place for awhile. The water pump is leaking coolant and need replacing it, so I'm driving it (and keeping the coolant topped off) while I arrange to get something else. The temp gauge stays in the normal range.
Yesterday on the road the car began to lose electrical power: the radio turned off, the gauge cluster and then the headlights got dimmer, etc. But it continued to run ok. When I got where I was going, I parked it for a few hours, then on the return trip the car started fine, the headlights and gauges were bright, but over the course of about half-an-hour they began to dim again. The car continued to run ok until I got where I was going and parked it. I'm not sure I want to drive it again until I figure out what's going on.
The battery is about six months old, and the alternator was replaced about two years ago. The serpentine belt is in place and seems to be in good condition. Battery connections and cables look ok. The "charging" warning light has never come on. The water pump has been leaking for a couple weeks, but this is the first time the electrics have acted weird. Would the alternator go bad this soon? Does the water pump affect the electrics? What do I look for?
View 2 Replies
My engine runs smooth in park or neutral. put it in gear and there is a slight vibration or the engine is running a little rough. is it the tranny trying to move the fluid? is this normal? Is this a vacuum leak? 2007 2.4 liter.
View 2 Replies
My truck runs very rough and lacks power when cold, even during the Texas summer. Once it warms-up, everything is fine. It's almost like turning on a light switch. If it's plugged in for a couple/few hours, it's smooth as soon as it starts. I'm assuming it likes the oil once it reaches a specific temperature. What my problem is?
View 14 Replies
My 2001 V70 24T runs smooth when cold as it warms up it runs rough with delayed acceleration reaction ....
View 1 Replies
I have a 1995 GMC that I have owned since new. It has 212,000 miles on it, a 305 TBI, and a manual five speed. It started running bad all at once. It idles rough, at different speeds and never settles down, (between 900 and 1300 rpm. It smells like raw gas, smokes, and has no power to get started from a stop. I checked the vacuum, it is at 19" at all rpms. The MAP sensor reads 0.3VDC when off, 4.12VDC when idling, and 1.5VDC at WOT. It appears to have 12PSI fuel pressure (after a messy test set up!) on the fuel pump side of the fuel filter (filter replaced 10,000 miles ago). The EGR valve appears to cycle OK when I suck on the vacuum line so I assume it works OK. I found a bad TBI flange gasket and replaced it. It runs slightly better but still smells like raw gas and has no power. When I try to accelerate, it immediately has no power, like a big vacuum leak. The idle is close to normal (900rpm = normal). Do I just start replacing parts?
View 9 Replies
THE FREQUENCY: This is a condition that has become progressively worse over the last six months. Initially it occurred once a week and now it is happening almost every day, lasts longer and is more acute.
THE SYMPTOMS: Initially and randomly, while driving at any speed, the car would begin to hesitate as if it might stall but did not- The hesitation was much like a shudder or power loss. At this time the check engine light would blink and stay on for a couple of days. This whole event would last less than a minute and the car would return to normal until the next one.
Now, six months later, it is occurring almost every day. At startup, at low speeds, at stop lights.... A LOT!
WHAT HAS BEEN DONE SO FAR: After frequent and unsuccessful visits to the Volvo Dealer all the plugs, the wires, the cap, and the rotor have been replaced with no luck.
The dealer says the code indicates a misfire on the #3 cylinder.
View 3 Replies
I have a 1994 Ford F-150 pickup with a 4.9 litre fuel injected inline six. Truck ran fine and took me to my destination but after sitting for 4 hours the truck would not start. Engine would turn over normally and could hear fuel pump running (didn't seem to stop) but truck would not start.
I changed fuel filter but truck would still not start. I removed air filter assembly and poured starting fluid in the air intake and engine started but idled roughly. Engine will rev up but runs very rough and lacks power when driven. Also the check engine light stays on.
View 14 Replies
