Mazda - Mazda3 :: 2008 Engine Noise At 1400 - 1700 RPMs When In Gear
Jan 14, 2012
I have a 2008 Mazda3. The car has a replaced engine with 24,000 miles on it. The engine was put in before I bought the car.The car and engine run like a top; except at certain RPMs and when in gear. When I have the car in any gear (auto), the engine makes a rougher noise at RPMs 1400-1700. As I apply more gas, the RPMs seem to get stuck at 1700, then it will break through and run smooth 2000+ RPMs. The engine sounds perfect at all RPMs except 1400-1700 when in gear. When I have it in park and rev the engine, the engine sounds perfect at all RPMs.
View 8 Replies
Advertisement
I hear a noise- what I can best describe as a metallic plucking sound - like a low metallic chord being plucked- when my automatic transmission 2008 Mazda3 shifts from first to second gear. It only happens the first time. I don't hear it after the car ihas been driving and is warmed up. Any thoughts on what could be happening?
View 2 Replies
Yesterday I just started noticing a clicking from my 2008 Mazda 3 sedan's fan. When the blower is set to "1" it is very quiet and inaudible when on the highway. As the fan speed increased from 1 to 4 the volume and rate of clicking increases. There is no difference with A/C compressor on or off or set to warm or cold. Is it the blower motor? Could pebbles be stuck in the fan? My repair expertise is almost non-existent (I changed the lightbulbs!) but I want to learn to do more with my car.
View 1 Replies
2010 Mazda Speed 3 ....My car has about 62,000 miles on it and has recently been having acceleration issues. 1-3rd gear seem under powered and what I am giving on the gas does not equal the power that should be coming forth, the RPMs seem to shoot up really high with no power transfer. When i am in 3-5th gear my acceleration is again funky with the slightest touch on the gas again causing the RPMs to jump high with no return of power to actually accelerate. I recently replaced the battery and changed the oil??
View 6 Replies
I'm having a problem with my 2012 Mazda3 (automatic, non-skyactive model) that others seem to be complaining about on the online forums, but there seems to be no consensus.
About 10,000 miles into owning the car, it started making a sort of high-pitched gargling sound when I accelerate and the tachometer reads 1500-1900 RPMs. At first, the sound occurred sporadically when I was accelerating under these conditions, but now, at 28,000 miles, it's happening almost every time I accelerate between 1500-1900 RPMs. Here are a few more facts:
The engine must be warm. The car must be in drive (I cannot replicate it in neutral or park)The sound occurs regardless of whether the AC is on
I took it to the dealer 3 times. The first time, they changed the belt, and that worked for about 1000 miles. The second time, they told me that the noise is normal, and I should not worry. The third time, I took it to a different dealer, and they put a "dressing" on the belt. That worked for about 600 miles. Now the sound is back again, and it's driving me nuts. It definitely doesn't sound normal. If I test drove a car at 28,000 that made this sound, I definitely wouldn't buy it.
View 5 Replies
The gear selector on my 2005 Mazda 3 with automatic transmission is difficult to move between P, R, N, and D positions. It does not "click" or fall into position like it used to. It has gradually gotten worse. When the car is in Park, it seems to not want to go all the way up into the Park slot. Even though the car actually parked, the P will not light up on the dashboard, which sometimes causes the car not to start when the key is turned. So sometimes I have to put it in Neutral to start.
Now the problem is that when it is in Drive, it will "fall out of gear". I put that in quotes because it is still in drive, but it was shift up to a higher gear if i don't physically pull the gear selector knob back. For example, if i'm driving and the car is in 4th gear going 60mph, and the shifter know slides up an eight of an inch, the D light will go off and the car will move into a higher gear (not sure which one, feels like 2nd or 3rd) and the engine will rev up. It doesn't feel like neutral.
Is there anything I can do myself? I plan on trading in the car in the next couple months, but I'd prefer to not have to get it worked on until then.
View 2 Replies
Took my car in for oil/filter change and in some odd circumstance, the young mechanic managed to drain 1 liter of transmission oil out of my car (which I didn't know at the time). After driving for 10 minutes (~5 km), I noticed my reverse gear wasn't shifting properly. After ~30 minutes of driving, my car was smoking from the exhaust pipe (turns out he had overfilled my engine oil too!!). Took the car back in to complain the mechanic supervisor claims my transmission is still fine and all I need to do is refill the lost fluid. Another independent mechanic later tells me my transmission line is likely fried if I had experienced what I did, and those guys should be responsible to replace everything. Since fluids have been topped up, I have no proof of who is right. So my question is, if I only drove for maximum 50 km after my transmission fluid was drained and engine oil overfilled, would that be enough to cause serious damage to the car?
View 10 Replies
I have a 06 f350 with 5.4 140k miles. Recently it has been shaking bad on idle but only in gear and it's hard to start when cold. The exhaust is moist at all times and the fluids never leak. When you floor it it hesitates feels like it's overly rich but if you let off a little it stars to pull again. Also while cruising at 1500-1700 rpms in any gear it will surge and skip. Only time it will miss and the CEL comes on is over 4000 rpms for a random misfire. Just put new coils in new fuel pump and filter. There has always been a cat code but it never effected the drivability. Could it be injectors?
View 3 Replies
I have a 2010 Dodge RAM Hemi Laredo pickup. Love it. Currently 34k miles. Have kept up with all maintenance. Since about 3k miles, I have intermittently heard a "grinding" noise at about 1400-1500 rpm. Usually while accelerating going up hill/inclines. Assumed it had to do with automatic gear shifting. Have reported this to dealer maintenance folks at each visit. They have reportedly not been able to identify the source, as they claim they do not hear it, despites numerous test drives. Everyone who drives with me has heard it!. I am concerned, as at 36k my full coverage for the transmission warranty expires. Incidentally, at 33,100 miles 2 broken studs were extracted from right exhaust manifold. A new exhaust manifold gasket and 2 new studs were replaced for a different niose. Are these related, or any clue about the "grinding" that I still frequently hear at 1400-1500 rpms?
View 9 Replies
I have a 2008 Mazda 3, and I have been bringing it to the same car wash for about a year now. It's the kind where the guys take it, while I sit in the lil' cafe and read. Eventually they drive it around front, wipe it down, clean the inside and hand it over. The last two times, the car needed to be jump started, because the battery would not start after the wash. The manager assured me this was normal, but the other guys at the car wash always seem surprised. Should I be thinking about getting a new battery? Is this really normal?
View 9 Replies
I have a 2008 Mazda 3 with 63,000 km / 39 146 miles.I bought it last year used with 50,000 km / 31 068 miles. I park my car on the street.Last winter I noticed that I frequently got frost on the windshield on the inside of the car. Is there a way to stop this from happening?
This winter I want to avoid having to scrap the windshield on the inside with the heater on max.
Do installing a window deflector will work? I am thinking that if I leave one of the windows slightly open but covered with a window deflector that frost will not form on the inside of the windshield. Is this correct or just wishful thinking?
View 19 Replies
My 2006 Tundra with 45000 miles on it has an engine vibration in neutral between 1400 and 1750 RPMs. It does not feel or sound like a miss fire rather a definite vibration. I have heard this is common with Toyota 4.7 litre engines. What might be some things that could cause it? It has always done it and after 8 years hasn't resulted in any engine failures.....yet.
View 5 Replies
I have a 2004 Mazda 3. I just had it inspected and cabin air filter replaced. Now, my car makes a loud noise when the a/c is on and I'm accelerating. The noise sounds like a fan is vibrating /something is blocking it or like a motor is rev-ing that shouldn't be. There definitely is something wrong that wasn't there before the filter/s replaced. I watched a Youtube video on it... a real pain to replace them, but it looked like the fithad to be pretty tight... Could the filters have been installed incorrectly or some part not put back together correctly?
View 2 Replies
A few months ago I bought a used 2008 Mazda3s sedan, and ever since I get an intermittent burning rubber smell from my rear left wheel. I recently got new tires, brake pads, and had the rotors turned, with no change.
The smell does not always happen, it will be there maybe one out of 3 or 4 times, and it is more likely to happen after long drives (e.g., one hour highway driving).
The wheel well also feels very hot. The obvious answer would be that the brake caliper is sticking, causing friction, heat, and the burning smell. However, if I touch the rotor it feels the same lukewarm temperature as the other three.
One additional thought is that this is caused by the exhaust, which is right next to this wheel well. I have noticed that the area of the floor of the trunk right above the exhaust gets very hot, which I had not seen in any other car I owned.
Could it be that the exhaust is causing the rubber of the tire (or something else) to overheat and smell bad? Visually, it does not look like the tire has a different wear or different appearance, compared to any other one.
This may or may not be related: my handbrake seems to be useless If I leave it on I can easily drive with little to no noticeable slowdown... I guess the previous owner did not read the part of the manual where it says you have to release the handbrake before you drive.
View 1 Replies
I have a mazda 3 and i just tried to start it but its just making a clicking noise. The radio works so does that rule battery out....
View 4 Replies
Last weekend we noticed that the engine temp was spiking. I still does. Sometimes it's a matter of just 8 blocks of driving before it's up, during which the heater doesn't want to blow hot air. Or, it will have a normal operating temp around town, and then start to spike when we hit the highway, and the heater works fine then (it even seems to take some of the temp off of the engine, like it should.) I took it to Autozone to have them run codes and it came back with a faulty coolant temperature sensor (I don't remember the CEL code.)
I have the replacement sensor and can replace it, but I'm not convinced that this is the problem anymore. Yesterday I had the coolant flushed, but I still have overheating issues. In fact, it seemed to be worse on the ride home from the coolant flush. Anyway, I noticed riding back from Autozone today that it felt like the engine was braking, as if my car were a manual. Now, I've ridden a few manuals before, and the braking I felt wasn't as heavy as the braking you feel when you release the accelerator and the clutch is still engaged, but it's similar. I think I'm a little overdue for a transmission fluid change. Could that be it?
My Mazda3 is a 2008 automatic with the smaller engine. It's stock.
View 19 Replies
My car is the Speed3 and runs great or it was. I recently had my timing chain replaced and it was running great. Been 2 weeks since the repair. Today coming home from work and exiting the interstate I was in 5th shifted down into 4th then 3rd. When I came to a stop behind traffic the engine died. I restarted it and smoke came from under hood. Wouldn't start so I had to push it over. Waited 15 minutes as tried many times just warning battery down. After 15-20 minutes I tried to start and it started but loud clanking coming from the engine. Stopped and checked oil. It was dry! Got oil replaced (5 1/2 qts). and started. OK to start but clanking sound is still there. On hook to the garage. There was no oil light or anything. Just got done running 70+ mph on interstate for 12 miles no problem.
View 4 Replies
The noise sounds a little like a baby Road Runner, a soft little "meep" sound. I usually notice it after the car has warmed up, when I come and go from a stop sign. In lieu of strapping somebody to the hood with duct tape, I've been trying to think of a tunnel that I could drive through fairly slowly with the window down while I attempt to replicate the sound.
View 3 Replies
I've got a 2009 Mazda3 hatchback, 31,000 miles. As I'm sure you know, it's very cold in the Northeast today. It was -12F on my drive in to work! I went out to lunch with a coworker today, and it had warmed up quite a bit to about 25F. As I was driving back to work - 40mph on a dry, straight stretch of road - my check engine light and traction control/stability control light came on. They aren't flashing, just steady. The traction control light will flash if I hit a particularly bad patch of slush, but it's never lit up on a dry road before.
Right after the light came on, the automatic transmission started feeling...funny. It was shifting hard, although downshifting felt okay. My coworker even noticed before I said anything. I don't think it was the traction control - it was specifically as the automatic transmission was shifting, not at any other time. I've read through the TSBs and didn't see anything relevant, and I've already made an appointment for tomorrow at the dealer. I've only got 5,000 miles left in my warranty so I'm a little nervous - the car has been terrific so far.
I would think the traction control light would be unrelated to the transmission, so I'm a little confused. Also, just to rule out a few other things - the last time I got gas was about a week ago and I still have a third of a tank. I don't think this is a gas cap problem or frozen gas, both of which I've experienced before (in other cars).
View 10 Replies
I have a 2008 F150 with a 4.6 litre in it. Last year I dropped a couple of plugs and had a factory new, second generation 4.6 installed. The motor only has about 25,000 on it while the rest of the truck has about 160,000. I was driving back roads in western Mass and went over a small, about four inches deep, pothole. I was driving about 35 miles per hour.
I didn't get any associated master warning lights. The RPM started rolling back from about 1700 to 0, and when they got to 0, the engine shut off. There was no previous sign of a fuel pump going bad, or of a bad fuel filter, which is also less than a year old. The truck has plenty of electrical power and turns over strong but won't start.
I checked the #9 fuse as identified in the manual but couldn't find an actual relay for the fuel pump, so I'm assuming it just has the 20 amp fuse which was good by the way. I'm thinking that the fuel pump would have given a few warning signs, but maybe not.
I did check the emergency fuel shutoff switch to make sure that it had not activated when I hit the pot hole and unless I'm resetting it incorrectly, it doesn't seem to have been set off.
View 7 Replies
I have a 3.3L 2007 Sonata. Within the past month, after first turning it on in the morning, the RPMs shoot up to about 1400 and slowly come down to normal after about 5 minutes. It does this in park and neutral, when I put it into drive it goes down to normal. If I drive it for a mile and put it back into park and neutral, it idles at a normal RPM. If I turn the car off for ten minutes and start it up again, it idles normal at about ~850 RPMs.
After doing a bit of google research, a lot of sites say that this is a normal thing for a cold engine to do. However, the RPMs have never gone that high previously. The check engine light hasn't come on.
View 1 Replies
