I have a 2007 Chevy Malibu with around 190000 miles on it. Recently, first thing in the morning then I start driving, that car will not shift into 2nd gear for a bit. The engine will rev up the 2000 RPM and stay there. After a while it will finally shift. The fact that the engine stays revved that high for that long makes me nervous.
View 9 RepliesI have a 2011 Chevy Malibu, with a little over 100k miles on it. A couple weeks ago it started acting a little funny when I would shift into reverse after starting it after sitting for a while. I thought it might have been due to temperature as it didn't do it after the car had warmed up or when it was warmer out.
Yesterday it started acting up really bad, will not shift out of first gear, and will not shift into reverse, and the check engine light came on. I was able to get it up to O'Reilly's to get the codes. It came back with 2 separate codes.
P0700 - Transmission Control Module (TCM) Requested MIL IlluminationP0776 - Clutch Pressure Control (PC) Solenoid - Stuck Off
The guy there seemed to think that the second code was probably caused by the first one, and most likely the TCM needs replaced. It makes sense to me, but before I head down this path I want to get some input, as it is a little over $300 for the part.
It is an automatic. (1999 Malibu) . Is it possible for a car to start but the gear shift to be frozen?
View 5 Replies2000 Chevy Blazer 4.3 (automatic) - When I bought it used, it shifted fine, has no issues other than the transfer case wouldn't engage every time. A few months later my overhead console display lights went out, then all the dash lights such as engine, 4x4, the gauges started lighting up and acting weird randomly, then a week later the truck started shifting funny.
Now 90% of the time, the truck won't start in 1st gear, it starts in 2nd, then while accelerating up to 30-35mph it will shift up way too soon and bog down, then shit back down to 2nd, then shift up again, and continue until it hits 30-35, then it fails to shift into overdrive. Also when coming to a stop, it kicks down a gear (into 2nd I assume) pretty hard and clanks pretty loud around 2mph just before a complete stop.
Weird thing is every once in awhile, it will go away and shift normal but the engine light is usually lit up during normal shifting.Could it be the ECM causing all these weird things?
The timing belt broke on my aveo, destroying the engine. I replaced the engine with a used one. Now I get the car back on the road and the automatic transmission won't shift from 3rd gear into 4th. Is it possible this problem was caused when the new engine was installed, or the transmission was damaged when the timing belt broke?
View 4 RepliesI had an '83 Chevy Malibu Classic that slowly lost power until it was nearly undrivable. I rebuilt or replaced every fuel or spark related item I could think of. I finally had the catalytic converter and O-2 sensor replaced. It ran better, then the problem returned about 8,000 miles later. Disconnecting briefly the exhaust did not work. This suggested that I was sold a new converter for nothing, but the mechanic must have done something to get it to run better. The question is: what was the problem and what did the mechanic do to improve it? (hint: I had indications of coolant contamination in the valve covers, any connection?)
View 3 RepliesSo my Malibu overheated for the first time, and note it just won't start up..
View 16 RepliesI own a 2002 Monte Carlo SS 3.8 6cyl. I believe it has a 4T65-E transmission.
On a regular basis if I drive 20 miles out of town, on my way back the transmission starts to shift hard (long shift?). From my research online, the 4T65-e is a faulty transmission to begin with. Is it worth replacing the Shift and Pressure solenoids? If I were to buy a new transmission where should I look? What are some model numbers?
Oil, trans fluid, filters are changed on regular basis.New catalytic converter. No Check Engine Light.
I have a 1998 bmw 528i (e39) with 200k on it. It runs and drives like a dream except for one little thing.... when shifting into the next gear at around 25mph, if I let off the gas just before it shifts it clunks as it shifts into the next gear. However, if I accelerate through the gear change it is smooth as can be and has no problems through the gears.
Secondly and I believe unrelated, I am also looking for the location of a transmission temperature sensor... I have heard they tend to fail and can cause issues with shifting until the car is up to running temp. I experienced an issues with it once not wanting to shift out of 1st gear until it warmed but that was before a filter and fluid change. Since that, I haven't any issues, but I want to be prepared just in case with one on hand ready to go in.
This problem started at the beginning of this winter. So I started to idle for 2 mins and the car was shifting without an issue.
However, now it is completely stuck and wont shift to 3rd gear even if I drive for 15 mins at 60mph.
It is a 2001 1.8T Golf, automatic. 75000 miles on it, mostly highway. I returned from my recent road trip, halfway across the country, which involved a couple of snow storms but otherwise everything ran smoothly.The day after I got back, I was going to dinner and the car wouldn't shift up out of 1st gear... unless I gunned it to almost 40 mph. Next time I started it, the check engine light turned on. I have driven it 3 miles, twice, since then and the problem remains. What the problem might be, if I'll need to replace transmission or just some fluid, or get a new car?
View 1 RepliesI've been have been having a problem with my car. It initially started at Christmas when I went up to MI for a visit. It would have problems shifting into gear after reversing. At first I just thought it was because it wasn't used to the really cold weather as we live in AL.When I returned it still did it, I would try the other gears available on the auto transmission and it still seemed to have a problem shifting from 1 to 2. It would slow down and you could rev the engine and it still would not shift.
All of a sudden it would kick and shift and you could drive. This only happened the first time you drove it that day. It would also kick very slightly when you went below 30mph. It doesn't do that anymore.I went for another visit up north and while I was there it started kicking whenever I was over 60mph. When i got back to AL I took it into the dealership as the check engine light came on. It now kicks all the time regardless of speed, though does it less at lower speeds, but if there is exertion on the engine like a hill, it kicks, kicks, kicks. When it kicks the rpm goes down and up.The dealer said that the things that needed to be changed are:- front assembly trans pump- crank sensor- gasket- oil pan.
I've tried taking it to a transmission place to have just the pump changed for less and all they wanted to do was give me a whole new transmission. This car is on it's third transmission as far as I know and a new/rebuilt one was just put in 2 years ago.After talking with my father (who was a engineer) he told me a way to check if the crank sensor a problem was to have the car in neutral and rev the engine. He said that it would still do the same problems if it was the crank sensor. I did this and it did not kick at all.Is there any real way of knowing if it is really the pump that is causing all these problems or if it really needs a new transmission or something else.
Chrysler Town and Country, 2003, 134K ...
I have the above referenced car with about 65k miles on it. Today I took it for a drive, switched it to tip-tronic manual and found that the car would not shift past 3rd gear. When I switched to automatic, the transmission stayed on tip-tronic (the display indicated I was on 3rd gear). I had to fully stop the car, place it on park and only then did the transmission switch to automatic.
View 1 RepliesI have a 2001 chevy cavalier, the base 2.2 model with a 5 speed manual transmission.
I can't shift into 1st, 3rd, or 5th gear. On occasion I can get into 1st but it pops out almost instantly. I have the shift boot up, it looks like the shifter won't go far enough to click into gear for the top 3 gears.
2nd and 4th don't have any issues, reverse works as well though can sometimes be more difficult than usual.
Why does my 2000 chevy impala whistle when i accelerate? it also seems to shift hard.
View 10 RepliesI went to drive my 1970 Nova today and after driving it for about 15 seconds it seemed to stick in second gear. I cannot get it to go into neutral to be able to put it into any other gear including reverse. The shifter is on the floor. I have no clue what is going on- If it's something with the linkage between the shifter and the transmission or something with the clutch. It has never acted this way before and gave no indication that a problem was on the horizon.
View 13 RepliesI recently had a spin out on the ice in my 2001 Honda Oddessy Minivan and had to have the back wheel and front rim replaced. I definitely hit the sidewalk at least once and ended up backward in traffic with the back of my van on the sidewalk. Just after getting the work done I noticed for the first time that my car was having trouble shifting out of park into any other gear when starting and when I had it running but put it in park. I have to either press the brake several times, all the way into the floor to get it to shift out of park or pump it once or twice quickly and when I hear a little click, shift it into gear. Is this a transmission problem? Could it have been caused by my spin out?
View 3 RepliesFor the past 3 months, upon shifting from 2nd to 3rd gear, the car lurches forward in a hard shift. Sometimes, it is nothing more than a benign "clunk", and other times it is violent, as if hitting a wall. This does not happen every time it shifts and even under identical acceleration, the results vary from none to violent. The number of violent shifts vs. small jolts has increased over time, and all other transmission functions and shifts are fine/normal. After much time researching the inter-blogs, I have come to no consensus on what is causing this or how to fix it.
Some say it is the adaptive shifting program and it just needs updating and others say it's the tranny and a rebuilt tranny replacement is the only thing that eventually fixed this problem (though one posting on the Hyundai forum is of the same exact problem, but the solution is worrisome -- contact negative battery terminal to positive, let sit for 10 min, reconnect, then drive at 1/3 throttle, shifting through all gears a dozen times. Poster says this resets adaptive shifting program and worked for him).
Finally, today, I took it in for a diagnostic with a local transmission specialist, and they could only replicate the hard shift once, but when that happened, he said the car went into limp mode and read two codes: P1193 and P2127. The car has never gone into limp mode (P1193) nor shown an signs of suppressed RPMs associated with this mode. Also, he seemed to focus his attention on the low voltage to the pedal position sensor (P2127) as being the major issue that is causing the hard shift. I also called a past dealer that worked on a similar issue with the car when I bought it used 4 years ago and they recommended updating the adaptive shifting program as they did last time; though I don't recall if the shifting issue was the exact same problem I am having now. So, a few things:
Does this sound like a computer issue or a tranny issue? Could the pedal position sensor having low voltage cause a shifting problem like this? Any merit to the connecting the battery terminals idea? Should I be wary of the mechanic that did the diagnostic today?
I have a 98 Chevy truck with a 4L60E. It has no second gear. I was sitting in park for about 10 minutes with the engine running, then put it in drive and it never shifted into second. It felt like it went straight to 3rd. I played with it manually until I figured out I had reverse, 1st, 3rd, 4th and torque converter lockup, just no second gear. My acceleration rate was medium and when I reach about 27-28 mph it would shift from 1st into 3rd. It has 230K on it so I rebuilt it with all the typical parts - frictions, steels, band, sun shell etc., still no second. I then pulled the pan back off and replaced the spacer plate and put in a shift kit. While I had it down I put a corvette servo in and did an air check. It worked fine. I could feel the band tighten.
Both the 1-2 and 2-3 solenoids checked good at 23 ohms. I swapped their positions to see if it would make a difference. I also checked to make sure the 1-2 accumulator piston wasn't stuck in its bore, the spring was new from the shift kit. It was fine. Put it back together...still no second gear. When I originally pulled the pan off for the rebuild, the pan was free of any debris and was very clean. I then drove it a couple of miles to a local transmission shop. They put their scan tool on it and drove it around the block. There were no codes and the ECM was calling for second gear. It doesn't sound mechanical since almost all the parts have been replaced, rebuilt or inspected that affect the 1-2 shift. It sounds electrical. Is there anything I have missed?
My dad's 1996 Chevy Silverado will not shift into hi gear. The truck starts up fine and he can drive it but for some reason it won't shift into hi gear. Him and I are clueless as to why it won't. He has a 1996 Chevy Silverado, 6.5 liter V-8 automatic transmission, and its a diesel. We really want to fix the truck ourselves so we are trying to avoid taking it to a shop.
View 2 RepliesMy 2007 es350 is already warmed up, so I know its not a temp issue.
My VSC light comes on (i know it comes on with any DTC)
My traction control light is on
My engine light is on
Now, when driving, it doesnt shift out of first gear till about 4K rpm and thats at normal acceleration (not flooring it) and shifts out of range on all other gears.
I can hear a humming/winding noise coming from the left side of the car (tray side) and it does it and I can hear it very clearly when letting off the accelerator (more noticeable at high speeds)