Jeep - Liberty :: Idling Rough With No Error Codes - Multiple Cylinder Misfire
Jan 21, 2012
ODB2 Code: P0300 - Multiple Miss-fire
I have an issue with my Jeep Liberty. It started idling rough with no error codes. about a week later it through the Multiple misfire code. I started by replacing the spark plugs. The old ones were from 20K miles ago and still looked good. Replaced them anyway. I still had the code. I put K44 fuel injector cleaner into the tank and drove it home (2 miles.) The next morning I started it and went in side because I had forgotten something. I came out to extremely thick black smoke. It went away after about 2 minutes, the computer code cleared, and the engine idled perfectly. About 2000 miles later the car is once again idling poorly. I added K44 again and for that tank of gas it ran fine, no code. Once new gas was added it threw the same error code and idles very roughly.
So here are some basic info pieces:
1. 8 tanks of gas from 8 different locations.
2. Adding K44 has shown a direct improvement both times, but more significant the 1st time.
3. New spark plugs
4. New coil packs
5. 2005 Jeep Liberty - 3.7L V6 at 99,872 miles
6. Hopefully unrelated is that the car has a small radiator fluid leak I haven't found. It requires 1/2 gallon every 2K miles or so.
There is no knocking sound, it just sounds like there isn't enough gas. Car responds fine to accelerator. Above 10mph car seems to drive smoothly.
View 7 Replies
Advertisement
I recently found these codes. My car is APR 1+. The car seems to run fine so I'm not sure what is going on. I changed the plugs at ~60K miles and now have 72K miles.
Address 01: Engine (CRZ) Labels: 06F-907-115-CDL.clb
Part No SW: 5K0 907 115 M HW: 8P0 907 115 B
Component: 2.0l R4/4V TFSI 0020
Revision: 5BH20--- Serial number:
Coding: 0403010A180F0160
[Code] ....
View 13 Replies
So on monday the following error codes appeared on my car. What needs to be replaced off the error codes?
P0300Random/Multiple Cylinder Misfire Detected2014-02-04 13:48:29
P0301Cylinder 1 Misfire Detected2014-02-04 13:48:29
P2030No Description Available2014-02-04 13:48:29
P3030No Description Available2014-02-04 13:48:29
C0033No Description Available2014-02-04 13:48:29
P0603Internal Control Module Keep Alive Memory (KAM) Error2014-02-04 13:48:29
C1400No Description Available2014-02-04 13:48:29
View 3 Replies
I have a 2003 Jeep liberty sport with 175k on it. it has a misfire cylinder 2 code. I replaced the plugs and coil packs on all 6 cylinders, noid light test on wires, compression check in all cylinders, everything works so far. I still have a check engine light for the misfire. I don't know if maybe the injector is bad for that cylinder, looks like it was recently replaced as with the other 6, or i have a leak of oil or air or coolant into that side either from the head gasket or intake gasket. the valve cover gaskets have been replaced recently as well.
View 6 Replies
We bought the car used for my youngest daughter and it had a couple of codes in it. 1st was the o2 sensor.. easy fix, grabbed an OEM one and stuck it in. Then there was the Cyl 2/ multiple cyl misfire codes that kept getting thrown.
I've seen a bunch of post about people pretty much doing the same things I started out with and still having a problem.....
1) Swapped around all the coils.. still got a #2 misfire... So, coils are good.
2) Swapped in NGK Platinum plugs with a .032 gap.... still getting misfire.
3) Replaced the crank shaft position sensor...... still misfire
4) Noticed that there was an Ebay injector in the #2 cyl...... when I pulled the plugs, that cyl was running a little lean..... bought an OEM injector to go back in there...... still getting misfire
SO, I tried using a propane torch head and putting out gas around the intake to search for vacuum leak and got no response....... so, for the heck of it, I went old school and grabbed a can of starting fluid and started spraying it on the intake around where it bolts to head... bam... found a vacuum leak on #2 cyl....... ordered an intake gasket off of ebay, spent about 3 hours on it pulling the intake and replacing the gasket,( the bolts had loosened up over time and there were small tears in the gasket allowing it to suck air) .. put the new gasket on, cleared the codes and it's been running perfect ever since.
Check for a vacuum leak where the intake manifold bolts to the head... might save time and money.
View 3 Replies
I was driving along and the engine started missing really bad. The whole car was bouncing around. At first I thought I had a flat, but when I stopped I noticed it was the engine. I checked the error codes and got 16684 and 16686 --- Random/Multiple Cylinder Misfire.
I had a problem recently with the vacuum hose broken and was causing an error code. Replace the hoses and it has been fine. Checked to make sure that the hoses were secure and they are fine. Doesn't seem to me to be related. So many problems for a car with 57,500 miles
View 6 Replies
My dads truck started misfiring last week, first thing i did was scan the codes and got p0303, p0304, p0305, p0306, and p0308. Its an 08 F-350 5.4...already changed out the spark plugs and the same codes came back. I decided to do some further testing and so far all coils had spark as well as 12.4 volts going to each. I did check the switching signal and that was present as well.
Moved on to the injectors and i checked each connector with my noid lights and it flashed on all cylinders. Did a resistance check on each injector and they all registered 12.4 ohms. We did switch some coils around and all the same cylinders misfire. My next step is to do a compression test.
My biggest question is if there are any common problems with these engines besides the coils, by the way this truck has the brown coil boots and the spark plugs that dont break in the engine.
View 3 Replies
My 2011 Accent's engine light came on recently. The mechanic said it was a cylinder 3 misfire and recommend changing the spark plug and coil pack for that cylinder. We did that over the weekend. Now the light is back on and has read 5 codes in the past 12 hours (4 at one time). They are P0303, P0304, P0003, P0403, and P0100. I have looked the codes up and can't discern if any could be caused by one main issue. About a month ago it read a code for the oxy sensor, but it went away and never came back.
View 3 Replies
So recently my 2009 hyundai accent has been idling rough, and has been very sluggish when accelerating. Usually the rough idling is the worst when the car is first turned on and tends to tone down as the car keeps running. I had the codes red and I believe it was C0302 C0303 C0304, saying that cylinders 2-4 were misfiring.
I replaced the spark plugs which didn't fix the problem, although cylinder 4 did have a small amount of oil above the spark plug and a little bit more below the spark plug, I am not sure if that means anything useful or not. I don't have a way to check the coils directly but I swapped coil 2 with coil 1 and checked the codes again and it was still cylinders 2-4 misfiring, so I would imagine that means the coil isn't the problem. I then tried spraying WD-40 around the vacuum tubes, and if the intake manifold is on the back of the engine I tried spraying it around that gasket as well, but I didn't notice a change in the idle speed.
At this point I am not entirely sure how to proceed, from what I have read the issue causing a misfire would be either there isn't a spark, which seems unlikely at this point, or the mixture of fuel to air is wrong. That is the part I am unsure of how to diagnose/
View 4 Replies
I have a cylinder 3 misfire and the vehicle is idling rough so I took it to the deal because I have a power terrain warranty. They're telling me I'll need a new manifold and plenum, coil pack, plugs, and gasket. Could this be accurate? I don't want to get screwed over...
View 9 Replies
5.4 3v. my last few weeks have not made me a fan. Here are the details:
I bought a 2008 F150 XL 5.4 3v with a cam phaser knock. Have done other timing jobs in past with no trouble so I was not too afraid to tackle this one. famous last words...opened the motor (shout out to the passenger side valve cover and its designer here) and found semi damaged roller follower on driver side. Worn cam lobe on the corresponding lobe and a loose chain on passenger side. proceeded to :
Change all timing components: phasers, chains, tensioners crank sprocket, all applicable bolts and BOTH cams as well as all lash adjusters and roller followers. most looked fine in fact all really did with a bit of wear on a few roller followers but only one bad one. engine didn't look to bad pretty clean.
Double and triple checked my timing chains and it was spot on. dark link on spot on crank, two dark links on the L and R dead on. put it back together. oh yes, changed all plugs with motorcraft ones, didn't even break one. did not change vct solenoids because I falsely assumed I could change the later easily if needed. they looked ok. screens intact etc... silly me for not realizing how kind Ford was in 2007 and later to necessitate removal of valve cover. I was reading a previous one on the how tos and assumed later models would be the same since it was the same sensor...
Cranked truck ran great. I mean perfect. sounded perfect. ran like a scalded cat. till it got to hot idle then it started doing its thing. rattle shake till you revved it. ran fine just wouldn't hot idle fine especially in reverse or under slight load. replaced driver side vct since ford only had one and I started on the easy side ordered the other one waiting for it. seemed to improve dramatically meanwhile I am driving this truck to test it. I drove it to work 50 miles each way and it ran great.
After a few trips it popped the P0420 light, seemed to run ok, cleared it watched it wouldn't come back. O2 sensor did seem to imply a bad cat on bank 1 since it seemed sensor two was mimicking sensor one and not staying stead like the other bank. still ran fine,
So I decided to check back pressure on the cat. I pulled sensor one out of bank one (really a joyously tight squeeze in there) hooked up my gauge and got 0 back pressure. revved it and all nothing. hooked sensor back up pulled truck out of shop and it commenced to running like crap. I mean bad. running worse than before I got it. Popping P0012 code continuously, and tons of misfire codes associated with bank 1 ..cyl 3 etc.. I tried swapping coils, pulled coils and checked spark with a tester and firing away looks like tons of good spark.
Now the weird part is : looks like bank one is dead. I can unhook any coil pack and/or injector and it runs the same and sounds like it is missing. if I unhook one off of bank 2 it almost dies or does. so bank 2 seems to be running fine. it will start and run but sounds like it missing sets flashing check engine light and backfires and stalls like crazy. I even second guessed my pressure gauge and unhooked exhaust manifold from pipe and it sounds even prettier when it backfires out of there but no change. I pulled cam sensors and cleaned it again and even tried swapping them since they looked identical but no change so I put them back.
Now I can only surmise that I am out of time somehow? or I have a gremlin perhaps? I like working on cars (usually) but this one is getting old. how do I verify what is wrong. if it is timing related how do I verify that now definitively once my marks moved I really cant figure out how to tell if it is in time? Since it has all new parts and they all ran beautifully till now. could it possibly be the vct solenoid doing all this? I plan on changing it when it comes in but surely it cant cause this many problems.. I unhooked it no change, and it does it at a cold idle and any rpm. really runs worse at idle but bad at any rpm.
View 3 Replies
I have a 2001 Jeep Liberty Sport 4x4. 150,000 miles. I had the ignition coil changed on cylinder #5 last weekend and then this weekend it started spewing black smoke out the tailpipe. Dealer says cylinder #2 is misfiring and he would have to replace the cylinder head. The main issue is that the part is backordered for an indefinite amount of time so I have no way to know if or when it could be fixed. If it could be fixed there wold be no guarantee it would work for much longer. It is obviously cheaper to repair the car than get a new one, but at some point the is the law of diminishing returns...
View 12 Replies
My car has been really acting up lately (AGAIN) so I took it in to have it looked at and they came back and told me it had multiple cylinder misfire, and they wanted like $1200 to fix it. What in the world does that mean and what is entailed in fixing it? They mentioned doing a full maintenance on it.
View 9 Replies
The Problem: Multiple Cylinder Random Misfire, Misfire on Cyl 2 and Cyl 3 codes. Runs fine on highway after first start in the am. Begins to misfire badly/throw code within 1 mile after exiting highway driving and starting "stop and go" city driving
The Car: 1999 VW Passat 1.8t "AEB" engine code
192,xxx miles. Greedspeed/Neuspeed ECU. All else is stock
****ICM module replaced less than 1000 miles ago due to misfire/similar problem. All was fine until now*****
Compression tested (cyl 1-4): 155lbs, 150lbs, 145lbs, 155lbs
Repairs/troubleshooting tried already:
Swapped cyl 2 and 3 coils for cyl 1 and 4. Result: problem remains / same error codes (cyl 2 and 3 misfire / random misfire)
Swapped cyl 2 and 3 injectors for cyl 1 and 4. Result: no change, problem remains
Tech is suggesting fuel system cleaning (to eliminate any carbon deposits in cylinders and clean injectors). Then look at replacing injectors if problem persists. Could I have another bad ICM?
View 3 Replies
The red triangle warning on my dash recently came on so I am taking it to the nearest dealer on Monday. I think all of this is covered under recalls/warranty. Am I right?
View 4 Replies
I have a 2005 jeep liberty 3.7L with 60,000 miles on it. The engine light when on 2 weeks ago and gave a p300 code. the dealership replaced coil and plugs, I believe. Then would start rough when cold, the engine light would blink for about 10 seconds then remain on. the car runs just fine except when cold....first minute of starting it. they checked for head gasket problem, and cant seem to find the problem. They told me that this could just be something that happens. I don't believe that. I have no loss of power, no hesitation. Runs fine 99% of the time
View 19 Replies
Replaced my water pump March 2nd using the "From Below" method. Started the car after and the check engine light was on and water pump was no longer leaking. I drove the GTI to Advance (15 Mins away) it drove fine and I pulled two codes.
P0300 - Random Multiple/Cylinder Misfire
P0301 - Cylinder 1 Misfire
The car pulled and drove normally. The next day the car is misfiring badly. Hesitation and bucks when accelerating until roughly 3k then smooths out.
I will swap my coilpacks and check if the misfire moves as soon as I can get my hands on an OBD2 Scan Tool.
From what I understand about the VR6 :
-The water pump runs off the serpentine belt
-Camshaft timing is controlled by the timing chain.
-Timing chain is not affected by the serpentine belt/pulleys.
Questions :
-Can turning the Crankshaft Pulley affect timing?
-Can that be the cause of the misfire?
24V VR6
View 7 Replies
Car threw a multiple cylinder misfire, changed plugs, wires, and then coil packs. Code keeps coming back.
View 12 Replies
What is going on with my sisters passat 2002 V6 GLX Auto 4Motion. Here is the codes:
16730-Camshaft Position Sensor (G163) Implausible Signal
P0346-35-00
16684-Random/Multiple Cylinder Misfire Detected
P0300-35-00
16688-Cylinder 4: Misfire Detected
P0304-35-00
16690- Cylinder 6: Misfire Detected
P0306-35-00
16689-Cylinder 5: Misfire Detected
P0305-35-00
I changed Both sensors and it still same problem. Car only has 40,000 miles didnt change timing belt.
View 2 Replies
my car was running fine yesterday. Today the check engine light came on and it started to run funny.. I checked the diagnostic code and it says the the cylinder is misfiring and that oxsygun sensor is malfunctioning. (Random/Multiple Cylinder Misfire Detected)
View 4 Replies
My '02 Elantra would have a hard time starting up in the winter right after I filled the gas to full. Usually I would have to give it some gas to startup. After that, it didn't have problems starting up until I filled it again. This was only in the winter.
About a month and a half ago, it became really slow to accelerate. Since the O2 sensor light had been on constantly for a long time I never bothered to check it. Soon the car became really slow to accelerate and would lunge forward in spurts. The error codes I got were P0133 and the O2 sensor. I replaced the spark plugs and the spark plug wires, and this seemed to do the trick. The check engine light went away, the car sped up nice and quick. Also at that time, I put in some fuel injector cleaner.
The a couple weeks ago, P0133 and P0420 came back. It seems like the car is using up more gas than it should. There is a very minimal sluggish response when I push the gas. I have a spare ignition coil, but trying to find what it could be more specifically before I swap out more parts willy nilly.
View 2 Replies
