Jeep - Grandcherokee :: 1994 - Complete Loss Of Power When Accelerating
May 13, 2013
1994 Grand Cherokee Laredo, 100,000 miles:
Driving out to see my BF this afternoon I noticed when I accelerated it hesitated a bit. I didn't think anything of it so I let it go. Driving home was another story. I was about 5 miles from home coming up to a red light and I started to brake, the light turned green and I hit the accelerator and I got no juice, I got across the highway and started to brake and the brakes locked up, the steering wheel locked up and then I lost all power. I got the Jeep to stop (right at the exit to a train station ) I tried to turn it back on and got no juice. I just got a new battery about 3 weeks ago. I called 911 since I was stuck in the middle of the road right outside the railroad station. Officer asked me to try to crank the engine again, asked if I had gas (have 1/2 tank) and then got me pushed into a spot until I can get a tow to my house in the morning.
The car has been fine, I never put "off" gas in, try not to let the gas get below half a tank.
View 1 Replies
Advertisement
My daughter drives a 94 Century (120+ K) and it was running great, no issues to speak of. Thursday morning she was advised that her brake lights were stuck on when the car was parked in school lot. This drained the battery. The battery was very old so she got a new one properly size & installed; the car started up and drove fine. Later that evening it started up and drove again with no issues.Next morning; NOTHING; No Start. I checked and when door is opened interior lights come on, insert key and door chime rings. Turn key and there is nothing at all, a total loss of power, lights go out, door stops chiming but nothing. Starter never engages, no noise, no attempts of the engine to turn, remove key and lights return and door chimes!
1994 Buick Century 3.1L SFI OHV 6cyl .....
View 3 Replies
I have a problem with my jeep grand Cherokee Laredo 5.2v8 losing oil pressure when the engine reaches normal operating temperature. the jeep sat for 2 years but we got it to run. when normal engine temperature occurs, the engine drops oil pressure and stalls. I have changed fuel pump,oil pump and oil pan gasket. also ran a cleaner through the engine. it doesn't matter if its winter or summer. the only way I can keep it running is to keep my foot on the gas pedal. if I don't do this the jeep stalls. a mechanic said it was the bearings. I don't believe this because there is no knocking noise when the engine is running. it has 103663 miles on it. it has just city and highway miles on it. never has been off road.
View 18 Replies
The problem began with intermittent stalling and now the Jeep will not start at all (no spark). I have had the cap, rotor, primary ignition coil, crank sensor, cam position sensor and PCM replaced without any luck. The repair bills have been brutal. The garage has given up.
View 8 Replies
When I drive over 55 i have a shaking through the car after driving for a while if you put it in reverse it feels like it is binding up and when you put it in park you can hear a thumping sound coming from the drive train i have replaced both cv shafts in the front (they were bad) and the passenger side hub. I am going to replace the ball joints with after market ones because it pulls to the right and the stock ones do not have a camfer adjustment is the binding a differential problem or a transfer case problem also if while the engine is off if you shift to neutral you can feel it release the tension on the drive train.
View 2 Replies
I have a 94 Chevy Suburban C1500 with a 5.7L, 350 Engine. It has 235,000 miles on it. I purchased it about 4 years ago with 191,000 miles in very good condition and obviously well maintained. I have continued to maintain it well.
For the past few months it has begun to start a little slower that before and when accelerating cold or warm there is a spot where it looses power. It doesn't sputter or die it just looses power. I can press the accelerator farther and it will come back to life and do fine. After a 20 -30 minute drive if I park for a while, 20 - 30 minutes, when I start it up it dies. The only way to keep it running is to give it the gas and smooth it out at about 1500 rpm for 10 - 15 seconds. Then I can drive it with no problem most of the time though it still has the dead spot on acceleration.
There is a good spray pattern from the throttle body injectors. Plugs and wires are relatively new and plugs look good (AC Delco Rapidfire Platinum). When I turn on the ignition without going to start, the fuel pump builds pressure for 4 - 6 seconds. I haven't checked the fuel pressure yet and am considering investing in the rig to do so. I recently replaced the fuel filter but that didn't work.
The check engine light has not come on but many of the lights in the cluster are burned out and I haven't felt like going to the trouble to fix that so it is possible that the check engine bulb is bad.
View 12 Replies
I own a rear-wheel-drive 1999 Jeep Grand Cherokee. I recently had both rear axle seals and bearings replaced. At the same time I had the mechanic check U-joints, shocks, etc. The noise from the failing bearings is gone, but now I have a loud "howl" that gets louder the more I accelerate. If I take my foot off the accelerator, the sound is gone. As soon as I accelerate, the sound returns. It is barely noticeable at speeds less than 35 mph, but the howl gets increasingly louder as the speed increases.
I returned to the mechanic the same day I picked up the Jeep. We went on a road test and I was given a story about gears in the differential and that despite the noise everything was mechanically sound. Even though the sound was not present before the seals and bearings were replaced, the mechanic assured me that nothing is wrong. This howling is giving me a headache!
View 1 Replies
So this little gem of an SUV has been good enough to me over the year that I have had it, but it is one of those used vehicles that has me scared to look underneath cause there is always something a miss.
I have been having some power problems and the OBD check engine light has been coming on. The engine like to putter like if it's not getting enough fuel from a clogged fuel filter when it gets going, hot or cold. Have confirmed that the fuel pump is with proper voltage and pressure. Though haven't noticed a big difference with the new filter. The check engine light cycles a code of 21, which is refinanced to the O2 sensor, both upstream and down stream. That tells me that there are TWO O2 sensors for this model. And research has confirmed this. One ahead of the cat and one behind the cat.
Here's the kicker, I only have one O2 sensor at the head of the cat and the location of where the second one would be located is only a solid section of pipe from cat to muffler. I haven't been able to track down the plug connection for the second sensor and these codes and problem only came after I gave the Jeep a tune up.
1994 Jeep Grand Cherokee Limited V8
View 5 Replies
I've replaced fuse underhood and fuse inside door panel. I've read about in the glove box there may be a fuse there for power windows? I removed the glove box panel to find 4 relays. Nothing is marked on these relays or panel. I read the numbers off these four relays inside the glove box to the clerk and she did not show any such thing on her computer for my vehicle. can a person pop out the main driver door switch and replace that?
1995 jeep grand cherokee 4x4 6cyc
View 4 Replies
1999 Jeep Grand Cherokee Laredo, 4.0 in line 6 Cyl misfires when driving. I bought this about 2 months ago (200,000 miles), and when i first got it it was acting like it was misfiring when driving above 60 mph( did get codes P0301 cyl 1 misfire, and P1391 CPS) . it started to act the same way just driving in my small town. so i ended up changing the ignition coil pack and changing spark plugs, i also replaced the CPS (camshaft position sensor). and was still acting the same way. I located a TSB that said there might be a carbon build up problem preventing valves from rotating and seating.
So I used seafoam and clean up the Top, and drove it in low gear at 4500 rpm for 15 seconds or so 6 times.. initially when doing this it was cutting out (jerking) when rpms got up there. after doing this twice with about 3 weeks in between never had a problem in town with it acting up running like it should from what i can tell..
Then i took a road trip, and a 60 mph was fine, 70 mph it was fine.. so i thought it fixed the issue and all good.. but about an hour into the drive it started acting up again.. unexpectedly cutting out for a second here and there, and usually when going up hill, and when got to destination about another 40 minutes, coming to a stop light i noticed it when stopping it was running pretty rough like it wanted to die out but never actually did. never got any more check engine lights either. I'm kinda at a loss at what the issue might be, and what i need to do to fix it as i really like the vehicle
View 4 Replies
I've got the feeling wire clothes hangers, duct tape, & screw clamps may be handy,;>). there appears to be a security cage around the fitting where the hose connects to the pump.
View 1 Replies
I drive a '98 Jeep Grand Cherokee Laredo, 6 cyl. engine, ~130k miles. I noted a slow loss of power steering fluid a while back and, after hillbillying it for a while (money was tight, and there was a sale on gallon jugs of PS fluid), I decided to address this problem properly and fix it. I added UV indicator dye to the PS reservoir and drove around for several days, hoping to pinpoint the leak. Well, what I found was wherever the fluid is leaking from, it's in a position to be blown by the radiator fan, turning the inside of my engine into an ultraviolet Jackson Pollock painting. (That, or I really am leaking power steering fluid from my #1 spark plug wire). Any tips on how I can pinpoint this leak?
View 6 Replies
So, I have a 1995 Jeep Grand Cherokee (Orvis edition) with about 270,000 miles. It still runs great and has been really useful in the snow this winter. A couple days ago the power steering pressure hose blew. My mechanic wants to replace it, but I can get a replacement hose locally. Is there any reason I shouldn't just do this myself. Do I need to worry about the fluid sprayed around the engine? The serpentine belt is only a few months old and squeaked only a little on the three mile drive to get it home.
View 8 Replies
Really scary, had my son in the car. Dash read "Check hybrid system". Reading some posts make me think that it may just be the 12V. Had it towed to my house.
60k GEN3 2010 Prius III
View 19 Replies
My son is primary driver of our 2011 Limited with push-button start. He phoned me a few minutes ago to tell me he was driving--everything normal-- when there was suddenly a complete loss of power, mechanical and electrical (engine died, dash lights out, nav screen dark, etc.). There was no advance warning of any kind.
The power loss was total but brief, two or three seconds, and then reactivated on its own. My son said he pulled off the road into a parking area, stopped the engine, waited a few seconds and then restarted and is on his way home with everything working normally so far.
First issue with the Sonata--61k miles ....
View 26 Replies
I own a 02 fwd v6 Santa Fe that just lost power on the interstate. It will go about 20 miles an hour and basically does not change gear unless it is in manual mode. I was able to drive it to a local repair shop but they are having trouble figuring out what is wrong with it.
First, they told me the plugs and wires were bad, changed those and still no power. Next, they told me it was the fuel pump, change that and still no power. Next, they said it was the catalytic converters but the said they unhooked them to test the theory and it still had not powered. They said it may need back pressure from the cats so that may not work. They want me to buy them but they are very expensive especially on a guess. Next, they told me if that does not fix it is must be the transmission. Will the cats off keep it from running due to back pressure? Does it sound like a transmission issue or could it be something else?
View 5 Replies
This first occurred about 2 weeks ago, I had a complete loss of power when stepping on the gas pedal. The engine did not rev or anything, completely unresponsive and the car was just gliding. I've had loss of battery power in the past where the engine was still going, just straining hard, but this was not like it as now the engine was completely not responding either.
I can't recall if it was going up or downhill -- it was around time the incline changed in a freeway ramp that began up and then moves down. At first I thought it was me accidentally putting it on neutral as I have a habit of resting my hand on the shift knob, but putting it in/out of drive did not work initially but after the 2nd try everything was back to normal so I thought nothing of it afterwards.
But if happened again this morning, again on a hill transition, either right before the top of a hill or right as I was coming down it. This time I know I did not have my hand on the shift knob. It resolved itself about the same, I had to shift in/out of drive a few times and it worked fine again a few seconds later.
I've been good with maintenance and changing out everything that they recommended, and also did the IMA battery recall upgrade.
View 5 Replies
About three nights ago I had a complete power loss on the highway and the car began to bog down alot under throttle (and surge at points as well although with no boost). It also idled very rough/erratically. When I unplugged the MAF it cleared up right away; Idle was smooth and it ran without hiccup but in safe/limp mode so very tame (again, without boost really, gauge shows it stays in Vacuum and never passes "0" or goes into boost).
I scanned it this evening and got 2 misfire codes and a MAF code, along with a code related to traction control which I noticed had activated as a result of this and could not be turned on (by activated, I mean the light came on, disengaging T/C). These things make me think it is MAF related, especially because I have bolt down Hitachi coil packs so I do not think that is what it could be in relation to the misfire codes (which I think may be old and needed to be cleared).
Fast forward to last night: I can pretty confidently say my MAF is not the problem and I think I saved an unnecessary expenditure. I was able to meet a friend with a 337 as well and his MAF did not change my car at all and my MAF ran fine in his car so I think my problems are something else. Although with the MAF plugged in my car runs very poor and unplugged it clears up and just runs "limp" (no boost and slow but stable) from what I tested this evening the MAF unit seems to not be the issue.
I think there must be a vacuum leak of some sort between the MAF and the engine which allows more air in than the MAF signals when plugged in which causes the issue. Also, I know a common thing to think is "coilpacks" but I have bolt down Hitachi coil packs so I would imagine that would eliminate those from being the failure they tend to normally be. Agreed ??
View 14 Replies
Background- 2000 Ranger, 3.0L 2WD 170,000mi. This truck is not my daily driver, i try to drive it once a week.
I've never had this issue before... I drove all over town yesterday; multiple stops, no issue. Today i go to do the same thing and upon accelerating out of the driveway i lose all power for about 3 seconds. I get power back for about 3 seconds then lose it again. This continues for as longs as i'm driving. Also, no CEL. I go back to the house to look things over, can't find anything staring me in the face really.
Truck idles fine and the issue is not present when i run up the RPMs in park. I've been reading some other threads about similar issues and most replies begin with checking the regular maintenance stuff i.e. TB, MAF, IACV, pcv, etc. It seems like a complete loss of fuel or spark...but only when in gear with constant throttle???
View 14 Replies
Having issues with a 2014 shutting down. Was at a stop light the other day and car completely lost power and shut down. When this happened oil, engine, and battery light came on. Once I parked car and turned off, it restarted. The dealership acted like I had no idea what I was talking about and would like to have some information when I take it back to have this problem corrected the car is not even 2 years old and has 30,000 miles on it.
View 14 Replies
I have a 2004 f250 superduty. I lost all electric to truck. No lights, radio, etc. Turn key and no click or dash lights. I put a charger directly to battery and nothing. Is there a main fuse in power line prior to the fuse box under the dash??
Also, right before this happened, I went to start my truck and my batteries were low, the truck turned over a few times, started dying, so I turned the key off, and the truck kept turning over on its own, as if the circuit remained closed for ignition due to low battery, and it turned over by itself until the battery was completely dead. But putting my battery charger on it now gives me no electric at all.
View 5 Replies
