I have a 1999 jeep cherokee 4 liter in line 6.tilt steering wheel is lock in one position. The handle that you release to move the steering wheel up or down don't have any tension on it.
View 1 RepliesI have a Jeep Liberty 2002 Sports. When it is cold and the car has been sitting for a while, when I start the car, the steering wheel is locked or hard to move. I have not tried to force it. But it will move if I rev the engine to a certain point. Once I rev the engine I can move the steering wheel again. I have left the car to warm up before revving the engine, but this does not work with the steering, I have to rev the engine in order to "unlocked" the wheel.
View 7 RepliesI easily removed the key lock cylinder but when I went to put the new one in I cannot get it to turn all the way back to lock the pin in place. The steering wheel is not in the locked position nor can I get it to lock. I have turned the steering wheel as far left and right as I could go with no success on getting it to lock or on getting the ignition key lock cylinder to turn back securing the actuator pin. The old key lock cylinder won't go back in either. What am I doing wrong?
View 3 RepliesMy 94' Jeep cherokee 4.0l 2wd has had an issue that the steering over the course of several years has get some play in it now. It also makes sounds as documented in the video. I should also note it doesn't seem to do it when it's warm, but when it gets around 50ºF or lower the problem is there. [URL] ....
View 2 RepliesI have a 1999 Jeep Grand Cherokee which I bought used. Last oil change they told me that the power steering pump was leaking. The leak was not enough to be seen, but it did seem to make some noise every once in a while so I took it in to get a new power steering pump at the dealer. Two days after they put the new pump in, power steering fluid was pouring out on the driveway, it was a really big puddle of fluid. I had to put new fluid in to drive it five miles back to the dealer. They said that it needed a new line, they were not sure why it needed a new line, they guessed because of the high mileage, 164,000 miles.
I told them that my Mercury has 287,000 miles on it and has never had the power steering pump replaced or the line either. I have driven most every car I ever owned 300,000 miles and have never replaced a power steering pump or line. But anyway, when the Jeep was supposed to be ready, they told me that the new line blew up spraying fluid all over the shop as soon as they started the Jeep and they had to get new parts so it would take another day or two. My question is what caused the new line to blow? My thinking is there must have been something wrong with the new pump or with the installation, somehow it was outputting too much pressure, anything that could blow a new line, would blow the old line.
I drive a 1998 Jeep Cherokee 4x4. I lifted it with a Rubicon Express 3.5" lift and had some drive line vibrations. So, I decided to purchase a slip yoke eliminator and use a rebuilt front drive shaft for the rear. I also starting having steering issues. The pump was leaking and the gear box was shot. Other than it leaking PS fluid all of the time, it wasn't a huge issue and was steering perfectly fine. I had a friend install the SYE, new steering pump and gear box in the same day.
When I drove away, there was a slight rumble from the rebuilt drive shaft and my steering was all screwed up. I could barely turn into a parking space. U-turns were completely out of the question. I assumed the issue was that the new gear box was off center and have been waiting for my friend to have the time to redo the job.
In the mean time, I decided to investigate the rumbling drive shaft on my own. So I removed the front driveshaft and swapped it with the rear. Problem solved! The rumble is gone! I am going to rebuild a different drive shaft for the rear and in the meantime, drive without a front driveshaft. Interestingly, my steering issue has completely disappeared. I can now do tight u-turns and park without a single issue. What the heck is causing the issue?
I keep getting this message on information center " service for wheel drive switch", I own a 95 jeep grd chero. 4.0.. Can I do this one myself or do I need a pro in shop to service? Where to start.
View 9 Replies2001 Jeep Grand Cherokee with a hard steering problem. I've changed the power steering pump, high pressure hose and gearbox.... the fan spins slow and it still steers hard ... could this be a hydrolic fan problem ???
View 10 RepliesMy 2004 Accent is stuck in the "lock" position in the ignition, and the wheel is locked and barely turns in either direction. I know this is supposed to be an anti-theft feature and I've tried all of the solutions listed here...
Turning the wheel hard and soft in either direction while holding the brake all the way down and trying to turn the key. Putting the car in neutral and then park and trying the above Disconnecting the battery for a few minutes and trying the above Jacking the car up on one side to release the tension on the pin.
My question is can I remove the spring at the bottom of the locking pin by drilling a hole in the center of the plate? I've seen a few youtube videos of this done on BMW's. It will cost me $500 minimum to replace the ignition or steering column based on quotes I got.
My '95 Grand Cherokee (104K miles) just started groaning when I make full turns. After first 1 or two turns, right or left, can hear the steering column groan and feel some resistance. Have I lost power steering fluid? or worse?
View 2 RepliesMy steering wheel locked up on me after i parked it it now says steering defective workshop..... I can't start it nor change gears it does nothing...the battery in the remote is fine what do i do?
View 3 RepliesI have a 2001 Jeep Cherokee Sport (128,000 miles) that has a groaning sound when ever you turn the steering wheel (and front wheels, of course). We were told by the former owner that it was the front wheel u-joints. I do not think that is the problem since it makes the sound when the Jeep is not moving forward or reverse. Is it typical for the u-joints or spindle joint (ball joints?) to make noise when they get older?
It makes a similar sound when I stand in front of it and try to push it up and down. When that happens, the car is not running and the wheels are stationary in all respects.
My steering wheel and ignition locked up 2 days ago. I tried turning the wheel and the ignition at the same time, tried the brakes, tried shifting gears and anything else i could think of. I think the problem might be with the ignition coils, or multiple ones, but i have bypassed that by hot-wiring the car(which was a pain because of all the anti-theft features).
So I have the car running now and it is almost drivable except the steering wheel is locked up. I need to know how to fix this, i have read plenty on it and i think i can break a pin that locks the steering wheel to make it work, but i don't know where this pin is(might be behind the ignitions, or attached to it somewhere). if i could do this without breaking anything that would be great, but if the car will run, I am ok with it begin broken, because i already hot-wired it so I'm not worried about breaking anything unless it will make the car not run.
2000 Honda Accord - will go to put the key into the ignition, key slips right in, but will not turn. The steering wheel is locked. This has been happening intermittently for a few months with no improvement. Sometime it will take me 10-30 minutes of wiggling the key, turning the steering wheel, etc until the steering wheel unlocks and key turns in the ignition. My patience is wearing and I'm concerned that it will eventually get to the point where it won't turn at all! I've tried with an alternate key and same results.
View 11 RepliesI have a 2008 Accent with 136,000 km on it. A few days ago I parked with the wheels slightly turned and the steering wheel totally locked, the key couldn't turn and the wheel couldn't be unlocked by pushing it either way. I called CAA and the driver had no luck but he tapped the key lightly with a wrench while it was in the ignition and it started. I took it to the mechanic yesterday and they had the same problems and called a locksmith who specializes in automotive locks.
They told me to take it to the dealership because they thought it was something further inside. Something was bugging me and I realized what it was. When the car was parked and the key wasn't in the ignition, as soon as I opened the driver side door the chimes went off. I closed the door, tried to lock it from outside with the remote but it wouldn't lock and the alarm wouldn't engage. I called my mechanic to tell him this and we all agreed that it seemed the car thought the key was in the ignition even though it wasn't.
I went to the dealership and left it and they called and said it was the ignition cylinder that needed replacing. Does this sound right?
First I have to say my Santa Fe is my pride and joy, never have I enjoyed a vehicle so much but today I encountered a problem. I went out to start my car, steering wheel is locked, key in ignition won't unlock, can't turn steering wheel to unlock.
View 2 RepliesCar 1998 Oldsmobile Intrigue
Engine 3.8 series II 160,000 KM
Problem : The Steering wheel won't move, I can start and drive the car forward/reverse but the wheel won't move right or left?? I was planning on scrapping the car in spring 2015 but need to move the car and don't have a clue on fixing this issue.
The key cylinder is located in the dash and I don't have any passlock II codes errors when trying to start the car, My power steering pump doesn't squeal or is locked (not Burning belts) but the pump is empty. I was thinking a seized rack & pinion but have never heard of that,I should still have manual steering I'm guessing still.
[URL] ......
I have a 1990 toyota celica. The parking attendant somehow locked the steering wheel and the key will no longer turn in the lock. I tried everything i could think of: turning the wheel whilst turning the key, putting car in all positions other than park and then turning the wheel and key, changing the key, etc....The steering wheel remains locked and will not unlock.
View 11 RepliesGot in my Treg turned key an nothing happened. Thought that somehow battery was dead. Hooked up jumpers to treg and touched both ends on the other side and had mean sparks!! Checked lights and lights are bright. Checked alarm and alarm is loud. Turn key and none of the gauges register. Starter does not turn over. Can't get car out of gear. Wheel is locked. Can get key out. Thought it was key fob and used spare. Same result. Bottom line, plenty of juice in battery, but starter will not turn over, won't come out of gear, and steering wheel is locked.
View 10 RepliesWent to start my car today but couldn't move my steering wheel at all??
Ignition still works and i can turn my keys but not the wheel?
I've got a 2007 rx 350. The steering wheel is locked and the key wont turn. I've tried everything, forcing the steering wheel left and right, forcing the gear shifter to neutral and moving the car. I even tried to spray some wd-40 on the key and then trying it.
View 14 Replies