Jeep :: 1970 - No Power Steering At Start Up / Distributor Cap Is Not Functioning?


Jun 4, 2015

I drive a 1970 Jeep Cj5 which I've dubbed, "The Red Bucket" because, well, it's red (duh) and because of its complete lack of doors, top, roll cage, and a folded down windshield. Anyway, I drove it to work about 2 days ago. Started fine, drove fine, no problems. When I came back from work it started fine. As I drove down the parking garage, the engine, a Buick Dauntless v6, just stopped. it didn't really even sputter either, just stopped, leaving me rolling down the garage with no power steering.

Now, at this point, I just though I had flooded it, happens all the time so I figured, "Hey, no big deal." If I've flooded it good, I normally only have to wait about 10 minutes till it springs back to life. However, after 10 minutes, 20 minutes, and 30 minutes, I was forced to call home to get a ride. Now I am a little worried, but I shrug it off thinking I have just flooded it really, really, really, bad. I drive up the next day to try and start it again, but only to find it in the same condition as the day before, starter turning, lights working, but still nothing.

Now, my knowledge of cars really doesn't go any farther than YouTube. I'd consider myself a "car guy," but I am no mechanic. That being said, based on my knowledge of distributor caps, my current hypothesis is that for whatever reason my distributor cap is not functioning. To go into more detail, there is starter noise, but no vibration or noise from pistons beginning to move and fire. Also, roll starting did not work and I am not out of gas, good thoughts though.

View 12 Replies

Advertisement

Cherokee :: 1991 Jeep Won't Start If Distributor Bolt Tighten

My jeep wont start if I tighten the distributor bolt, it will start and run fine if i leave the distributor loose. Has been running that way for 2 years and i just was wondering what would cause that kind of problem... 1991 Jeep Cherokee Laredo inline 6 ....

View 3 Replies

Ford - Mustang :: 1970 - Won't Start Intermittently?

Purchased this car almost two years ago and it would typically start up no problems after sitting overnight or for a few hours. However, after running the car and then say turning it off to pump gas or just for a short stop, it never starts up right away. Just this week I had it taken to a friends repair shop (yeah, I know) and was told they moved/adjust distributor caps and checked carb and that they saw no other problems and they had it starting it up every time. They had suggested that what I needed to do was run the old gas (its only been sitting about 3 months) and keep running premium until we are certain that nothing remains in the tank except new gas, but assured me that the car was good to go and they sent me on my way.

Now, they didn't charge me, which is great, but I got what I "paid" for when I took the car out for about a 45 minute cruise, stopped for gas, and without fail the dang thing wouldn't start. A lovely citizen at the gas station raised the hood, fiddled with the carb, as he didn't think it was a battery issue, and was able to get the car going and get me home, but again, car wouldn't start about 20 minutes later. Hours later, out of curiosity, attempted and car started just fine.

View 13 Replies

Jeep - Cherokee :: Power Steering Pump Leaking

I have a 1999 Jeep Grand Cherokee which I bought used. Last oil change they told me that the power steering pump was leaking. The leak was not enough to be seen, but it did seem to make some noise every once in a while so I took it in to get a new power steering pump at the dealer. Two days after they put the new pump in, power steering fluid was pouring out on the driveway, it was a really big puddle of fluid. I had to put new fluid in to drive it five miles back to the dealer. They said that it needed a new line, they were not sure why it needed a new line, they guessed because of the high mileage, 164,000 miles.

I told them that my Mercury has 287,000 miles on it and has never had the power steering pump replaced or the line either. I have driven most every car I ever owned 300,000 miles and have never replaced a power steering pump or line. But anyway, when the Jeep was supposed to be ready, they told me that the new line blew up spraying fluid all over the shop as soon as they started the Jeep and they had to get new parts so it would take another day or two. My question is what caused the new line to blow? My thinking is there must have been something wrong with the new pump or with the installation, somehow it was outputting too much pressure, anything that could blow a new line, would blow the old line.

View 3 Replies

Jeep - Grandcherokee :: Power Steering Fluid Leaking?

I've got the feeling wire clothes hangers, duct tape, & screw clamps may be handy,;>). there appears to be a security cage around the fitting where the hose connects to the pump.

View 1 Replies

Jeep - Grandcherokee :: 1998 - Locating Power Steering Leak?

I drive a '98 Jeep Grand Cherokee Laredo, 6 cyl. engine, ~130k miles. I noted a slow loss of power steering fluid a while back and, after hillbillying it for a while (money was tight, and there was a sale on gallon jugs of PS fluid), I decided to address this problem properly and fix it. I added UV indicator dye to the PS reservoir and drove around for several days, hoping to pinpoint the leak. Well, what I found was wherever the fluid is leaking from, it's in a position to be blown by the radiator fan, turning the inside of my engine into an ultraviolet Jackson Pollock painting. (That, or I really am leaking power steering fluid from my #1 spark plug wire). Any tips on how I can pinpoint this leak?

View 6 Replies

Jeep - Grandcherokee :: Power Steering Pressure Hose Blown

So, I have a 1995 Jeep Grand Cherokee (Orvis edition) with about 270,000 miles. It still runs great and has been really useful in the snow this winter. A couple days ago the power steering pressure hose blew. My mechanic wants to replace it, but I can get a replacement hose locally. Is there any reason I shouldn't just do this myself. Do I need to worry about the fluid sprayed around the engine? The serpentine belt is only a few months old and squeaked only a little on the three mile drive to get it home.

View 8 Replies

Jeep - Liberty :: 2008 - Power Steering Fluid Into Brake System

I had a line blow on my steering rack, and I was taking it to the garage well I decided to add some power steering fluid but instead I added it to my brake system , (yes I know it was bonehead move on my part when I do know the difference). Any ways I drove my 2008 jeep liberty about 5 miles to the garage, they are changing my rack and pinion because the initial problem, but my question is do I bite the bullet and change the master cylinder, brake lines and calipers??? I do a lot of driving on highways , and I am been getting mixed answers yes change it all and no just flush it out.

View 9 Replies

Civic - Honda :: 1994 - Won't Start Until Gas Is Pumped - Fuel Pump / Distributor?

I have a 94 honda civic. It's been having problems starting. When it won't start you have to pump the gas a lot and it will then start. You can smell a lot of fuel when this happens so unsure if it is the pump. Maybe it's a combination of several things. Replaced spark plugs, new wires connecting to battery. And just put in a new fuel filter. All seemed to slightly work for a minute. But now driving today went to start the car and it wouldn't stay running if I let go of the key. Finally got it to stay on seemed fine then as I was driving and wasn't pressing on the gas peddle the car started losing power so I pressed the peddle it sputtered (kinda sounded like something clogged in tail pipe) and regained power.

View 19 Replies

Windstar :: 2000 - ABS Not Functioning / Rapid Repeated Turning Steering Wheel Has No Effect

Windstar 2000, 260K, ABS not functioning, previously ABS light on all the time now of even with Key on Engine Stopped. While a long drive after 1600 KM failed to apply the Cruis. Horn not blowing. Retried cruise engaged but resume, horn, deceleration did not not function. Stopped, disconnected battery for half hour cruise and horn started functioning. Again after 400 KM stopped functioning. Now it is intermittent. Tail lights normally working. Cruise deactivating switch (switch unser the master brake cylinder) was changed by ford 5 years back, it is dry no signs of brake oil on it. Fuse no 10 is OK. Rapid repeated turning steering wheel has no effect. CEL On since 4 years code is for bank 2 CTM.

View 7 Replies

Ford F-150 (2004-2008) :: Slow To Crank / No Power And Won't Rev At All - Distributor Cap Location

I know this is a ford truck site but today I was trying to clean some corrosion off my battery post on my ford fusion with water. Well when I went to crank it up it was slow to crank and it has absolutely no power, won't rev at all. From what I already knew, it seems like some moisture got in the distributor cap. Am I right and if I am were can I find the dang thing and how can I fix it?

View 3 Replies

Jeep - Wrangler :: 1995 - Won't Start - Power Isn't Getting To Fuel Pump?

So last week something happened that I've never had happen before. I was dropping my daughter off at school and I noticed that my dash lights weren't on. My headlights still worked and the blinkers did to.

When I got home and parked it, I checked out all the fuses. There was a 20 amp fuse that was blown, so I replaced it and then checked the relays under the hood. I turned on the key to check the dash lights and they still didn't work. The 20 amp fuse blew again, so I replaced it again. Now the dash lights work again.

However, when I tried to start it, it would turn over, but the fuel pump isn't turning on.

Long story short, I've replaced all 4 relays under the hood, installed a new fuel pump and also replaced some bulbs in my taillights and sides over the front tires. It turns over when I try to start it, but the fuel pump still isn't "kicking" on and it won't start. I feel like somehow, power isn't getting to the fuel pump.

View 12 Replies

Passat (B5) :: 2000 - Won't Start - Inside Lights Stopped Functioning

While I was driving my 2000 Passat GLX last night, i noticed that the windows and the inside lights stopped functioning. When I reached home I also noticed that the car was not responding the remote lock either. This morning, I tried to start the car but there was no response from the engine although all the panel lights were on!

View 10 Replies

Explorer :: 2002 XLT V8 - All Locks Not Functioning But Have Power

I have a 2002 Ford explorer XLT V8. My door locks recently stopped working, including all switches to lock and unlock, and the rear glass hatch lock. My alarm comes on when I hit the buttons on the remote, but the key pad and switches don't do anything. There is a click coming from a harness that is above the rear passenger seat belt so when you use the remote and the switches so I know power is getting to that point at least.

View 1 Replies

Ford - Escape :: Rear Power Lock Is Not Functioning?

My rear power lock is not functioning. When I hit the power locks, the other three power locks work, but the one will not function and I can hear the actuator make a prolonged electrical noise (like a deep whine). Is it safe to assume that I need to replace the actuator? I just don't want to throw parts at it.

View 2 Replies

Golf/GTI VI :: 2015 - Power Mirrors Not Functioning Properly (or Not At All)

Some time ago my power mirrors stopped working. I don't normally adjust my mirrors all that much since I'm the only one who drives it but when I have, adjusting the mirror knob does nothing... and when it does, moving the joystick down will move the mirror up!

Depending on whether the lights are on or off all seems to change whether or not the mirrors will work. My right mirror seemed to be working fine but then that stopped as well.

Nothing is ever consistent; either they don't work or work very intermittently.

I've pulled the door skins off and nothing is torn or ripped wire-wise, changed the knob to a brand new one and still nothing.What it could be?

I'll bring it to my mechanic and sure enough it'll work when tested then will stop working randomly. Everything else electric wise seems to be fine (windows, horn, headlights, locks).

Some other details:
2015 Golf 2.5L 50k miles
Sunroof
Base model
Heated Seats
V2 Autopilot
LED Tails w/ euro fog (no error bulbs)

View 2 Replies

Elantra MD (2010-15) :: Center Console Power Outlet Not Functioning

I just bought a used 2012 Elantra GLS with 24K miles. I tested almost every possible function of the car before I bought it however I didn't try out the 2 power outlets expecting them to both work on a car with only 24k miles.

Anyway, the center console outlet doesn't work. I'd like to check the fuse box first thing in the morning. I work night shift so I won't be able to get to it til then. Any other things I should look for?

View 24 Replies

Ford 6.0L Power Stroke Diesel :: 2004 - Beep / Flash On Lock And Unlock Not Functioning

My 2004 6.0 used to beep and flash the lights when I lock and unlock with the remote key fob, but has stopped doing it for some reason. Need the sequence required to re-program that feature.

View 1 Replies

Ford :: 1970 - Slips Out Of Gear

Early 70's Ford Truck w/Dana 20 Xfer case

The problem is that when I put the truck in 4W Low, it will sometimes slip out of gear into 4W Neutral. It happens more often when climbing hills than driving on level ground. It hasn't ever slipped out of 4W High. It is drivable the way it is, but it's annoying. If there were an easy fix I'd do it. If I have to remove the xfer case, that seems like a big job, so probably not. What do you think?

The manual suggests these four as possible reasons

Shifting poppet spring weak.

Bearing broken or worn.

Shifting fork bent.

Improper control rod adjustment.

Which is the most likely problem? What is the "poppet" for and where is it located? Can anything be done to diagnose or fix this problem w/out removing the xfer case from the vehicle? What about the control rod? Can it be adjusted with the xfer case installed? If so, where is that adjusted?

View 7 Replies

Pontiac - GTO :: 1970 - Unpainted Transmission Is Original?

I have a 1970 Pontiac GTO that i am restoring. It has the original matching numbers YS Code 400 HO engine. When I got it a few months back, it sounded pretty rough. We removed a valve cover and found a bent push rod. At that point we decided a complete rebuild was in order. We removed the motor and transmission from the car. I'm want to know if the transmission is original to the car but I don't know how to check the numbers for that. However, I could have found a clue. When we cleaned the motor and transmission I found the motor had been painted twice - the factory color with another blue over the top of it; the transmission had never been painted! Did GM ever produce cars and send them out with unpainted transmissions or has it just been replaced at some point?

View 18 Replies

C/K :: Restoring 1970 Chevy C10 - Drum Brakes Not Coming Off

I've begun restoring my grandpas 1970 Chevy c/10 but I can't seem to get the brake drums to budge. I tried several cans of lubricant and even beat on one with a sledge hammer till the outside broke off. But the front face of the drum still won't come off. How to remove them?

View 14 Replies





Copyrights 2005-15 www.bigresource.org, All rights reserved