Jaguar - Xj6 :: Misfiring Cylinder 5 / Car Started Shaking With CEL Came On
Oct 30, 2011
I used fuel injector cleaner in two different gas tanks; the car started shaking and the check engine light came on. The mechanic changed a sensor but the car was doing the same; I was told that it will take 4 full gas tanks to clean the gas lines. I went to autozone and they told me that the car had a misfire on cylinder 5 and multiple misfire as well. I do not trust the mechanic any more since I had to take the car back to them several times and still is not fixed. They also did a full tune up and the check engine light still on and flashes when I am going about 55 mph.
View 3 Replies
Advertisement
My Prius started shaking pretty bad when the ICE is running. This morning I got the codes read and it came as Cylinder #1 misfire. I figured the coil pack is going bad (as is known to happen) so I swapped #1 and #2. The misfiring actually got better for about 30 minutes, but it finally happened and the CEL flashed again.
So I took it to get the code read but he said the only code is still #1 misfire. Perhaps the ignition coil is OK then? I bought a new spark plug, maybe the plug has gone bad. The plugs only have 45k miles on them. I'll swap it out and see what happens. What I should do to diagnose the issue? It seems to be slowly getting better...this afternoon it was much better than this morning but still shaking sporadically.
View 17 Replies
My daughters '09 Corolla was shaking and misfiring occasionally. When she took it to the shop the mechanic had it for a couple days and after many attempts finally reproduced the issue. After several diagnostics tests they determined it to be a damaged cylinder. We had the option of
1. replacing the engine
2. retooling it
I called around to a couple other mechanics and they told me the same thing. One particular mechanic (no affiliated with Toyota) told us that he had heard this happening on both the Camry and the Corolla. Sound like a manufacturer issues if it's been seen frequently.
View 5 Replies
2007 GMC Sierra 1500 (MAX) ... This had happened before 3x, but was about to turn truck off and wait 10 second and turn back on. Then truck would run fine for months. I found this on my truck manual.
My truck is riding differently. Here's the story - I put new tires on Friday, an hour later, my truck started to ride rough. The light on dashboard is; Check engine, Engine power lost (truck would not get up when this was shown on dash. This error has not come up again), stibilitrac check. Truck's driving performance; Idle sputters (like RPM rising, but they are not, it’s just the engine shaking), once driving when it shifts hard at 3000 RPMs (only 2nd gear). I took my truck to Advance, and this was the error code I received; #6 Cylinder Misfiring and Actuator module.
I changed all spark plugs and number #6 was very dirty compared to the other and smelt very much so like gas. I have not driven this truck only cracked and it stayed in park. I had a person look at it, and he said that the #6 cylinder was the only problem he could find when he hooked up his code thingy. Now he played with everything and took out the #6 spark plug (this is now Tues) and said that it didn't smell of gas like it should have. At the end. he stated that we first should change the Injector for #6. and if that did not correct the problem, then he would recommend the lifters to be replaced. I asked how confident he was about "his" diagnosis. and he stated.... I am not a GM mechanic... wow. now I am confused as to what I should really do! BTW, he never cleared the error codes...
View 16 Replies
About a week ago I was driving my Pontiac 2003 Grand Am V6 and it began to violently shake and the "check engine light" came on and started blinking. I then immediately took it to the mechanic It has been with the mechanic for 6 days and they were unable to locate the problem. They called me today and I was told that I have no compression in one of the cylinders (I have done business with them before and felt comfortable in that I wasn't being taken advantage of). Also, is there any problems in the future with getting a cylinder replaced i.e. other parts of the engine that might correlate?
View 17 Replies
My '98 4.0 has 213k on it and the other day I started the engine and the jeep started shaking like crazy. Eventually the engine quit and refused to turn over so I looked under the hood and quickly discovered the problem, a deteriorated rubber elbow on the left manifold. The elbow connects to a threaded breather type valve in the manifold and has a thin piece of black plastic routing to the purge solenoid next to the left fender/air box.
When I removed the rubber elbow from the manifold the engine eventually turned over and idled fine, I then headed to autozone and found replacements of the same diameter, I cut them down a bit to match the length of the originals. Since its been a while I changed the plugs and wires, coil pack along with cap and rotor while I was at it. I replaced one plug and wire at a time to ensure I didn't mix things up, same goes for the cap. Now the jeep seems to take a few more seconds to get started but once it does it idles fine.
Now when I hit the gas hard the jeep will hesitate and then backfire. If I'm smooth on the gas the jeep drives good, whether city or highway. When coming to a stop the jeep will sometimes buck slightly like it wants to cut but doesn't. The backfire sounds like its coming from the air box and oddly enough, my aftermarket radio no longer plays in the accessory position, probably a separate issue. So far there's been no check engine light.
I really need to keep this jeep for a few more months and I would hate to put big money into at this stage.
View 3 Replies
My car has had random misfiring when at idle and has been shaking really bad but once I accelerate and get up to speed the vibrations and misfiring stop but the check engine light flashes for a few minutes. I have changed spark plugs, all 6 ignition coils the intake manifold gasket and both camshaft position sensors. My car has 180K the codes that are showing up are 300,301,303 and 0016. I really love the car and have had no prior issues the car before this ran like a champ.
View 2 Replies
Happened a few times on me lately. While pulling towards the top of 5th, I'll start to see the check engine light briefly blink as if the car wasn't sure, then at the top of 5th, she'll start misfiring on cyl 2 and 5. It's only during the long haul pulls that this occurs. My plugs and coils were all changed about 1k miles ago.
View 17 Replies
So as I was heading out the other day, the car had low acceleration and engine shaking. The check engine light started flashing.
Checked the codes at the parts store: P0300, P0301, P0303.
I just dropped it off at the auto repair shop.
Could it be a I'm just wondering if I shouldn't have taken it to the dealer as the printout says it could be a CPU issue?
View 5 Replies
Took this car for scheduled maintenance, tuneup on 12/19. AFTER the tuneup, it started shaking when in idle or going slowly. Took it back 1/5, they confirmed it was misfiring, checked a computer code, replaced one of the coils. The misfiring went away but returned, worse than ever, last week (early Feb).
I read somewhere that replacing coils for misfiring can be just treating the symptom, not the cause. What should I do now?
View 13 Replies
Going up a hill this LS started shuddering and misfiring and set the po302 code. A small push on the accelerator sometimes seems to temporarily remedy the issue. This started about a week ago. fuel mileage : 26 mpg highway
Here's the readings I got at idle:
Fuel pressure is KOEO - 0 (That's what it read.); KOER - 30.
MAF - about 70
LT FUEL TRIM 1 - 5.5
ST FUEL TRIM 1 - STAYS NEGATIVE
LT FUEL TRIM 2 - STAYS NEGATIVE
ST FUEL TRIM 2 - STAYS NEGATIVE
ST FUEL TRIM 11 - STAYS NEGATIVE
ST FUEL TRIM 21 - STAYS NEGATIVE
O2 1 - NORMAL FLUCTUATES PROPERLY
O2 S12 - STAYS ABOVE .500
O2 S21 - NORMAL FLUCTUATES PROPERLY
O2 S22 - STAYS ABOVE .500
Not familiar with this vehicle...
View 2 Replies
I have a 2008 Touareg 2, V8, 4.2L.
I bought it used (~95k miles) and almost immediately had an issue. #5 is misfiring. Since then, it has been in the shop 10-12 times with no resolution. Here is what I have done so far:
Put in all new plugs/coils sent the ECU to SIA electronics in Chicago for testing - no errors replaced the injector with a new injector on #5swapped #1 for #5 (plugs/coils)checked the harness (dealership said they did this, but not sure if they did or are just tired of me)
Through all this, #5 is still misfiring. The dealership is out of options, suggesting that the ECU is faulty and needs to be replaced ($1600) or they need to swap the #5 injector with #1 to see if that is the issue (~$1000+). Neither of these options sound reasonable because a) the ECU was already tested and b) the injector is brand new, yet the exact problem (#5 misfire) has persisted before and after the injector replacement.
View 3 Replies
My dad has 2006 passat 2.0T. In December 2010 he went overseas. During his absence the car was parked in garage and not in use.
So one day I decided to start the car and as soon as I turned it on the car made this noise and check engine light came on. Took the car to a private repair shop and found out the cylinder #3 was misfiring. The tune up for this car was due so I had all four spark plugs changed and the car ran fine for few days. Then couple of days later it started making the same sound and this time around the coil for cylinder #3 was replaced.
A few days after that check engine light came back and this time it was blinking and the engine was struggling to run, took it again to the workshop yesterday and this time another coil not sure which cylinder was replaced. (all this is done at a private workshop). I have a hunch that the car is going to run fine for a day or so and the problem is going to come back
I never had any major issues with it up until now. Bought this car new in 2006 from dealer. I am afraid that this might be a start of a downhill roll from here on I will drive the car tomorrow and see how it reacts.
View 7 Replies
I've done just about everything me or my mechanic cannot figure out why cylinder #3 is misfiring has new plugs coilpacks checked wires etc. I love this car and will not put it to sleep!!
View 2 Replies
The car already has a cel even though I just bought it. Drove home from work this morning had no problems, went to go shopping no problem, come out start my car and it won't idle right, problem. The Cel flashed at me and once driven a tiny bit stayed constant. Seems like a cylinder is misfiring because of the sound it makes and it is hesitant when you give it some gas. What could it be, coil packs (which is what is was in my 24v) MAF, spark plugs?
View 22 Replies
I just had all 6 fuel injectors changed as they were rusted. But the 4 and 6 are still miss firing. I am going through gas more than I should. I had the EGR replaced as it was stuck open. I do not want to pour more big money into this thing. What can I do. Sea foam is not working. Could it be another problem. I am starting not to trust the mechanics.
View 12 Replies
My 99 Explorer XLT V6 SOHC has been misfiring lately. In idle the RPM needle fluctuates a bit and the vehicle vibrates and shakes. At night when the lights are on I notice them dim a bit as the engine struggles in idle. It doesn't stall very often at all. Accelerating I notice way less power and the engine studders. That's when the engine light comes on flashing. Then remains on solid afterward. I brought it to a mechanic friend who read the code and it was cylinder two misfire as well as the O2 censor.
I replaced the plugs and leads and censor. Noticed the plug in cylinder two had little to no gaping. Thought I had fixed the problem. The vehicle ran perfectly. Three or four days later driving on the hwy same problem came back. Thinking it must be the coil pack I got one for a good price and replaced it. Again, the truck ran great for four days and now the problem has returned. Same thing, shaking studdering and flashing engine light. I have verified the locations of the wires and plugs a few times so i believe they are all properly installed.
View 1 Replies
My 1988 240DL is miss firing #4 cylinder. I cannot get it to fire. this is what I have done:
Swapped plug wires with the #3 wire. Miss fire does not follow the wire
Swapped plugs with #1 plug. Miss fire does not follow the plug
Tested injector power with a tester and it lights up properly
Replaces #4 injector with a new one, still miss fires.
Replaced cap and rotor
Compression test shows 150 LB in #4
sworn and thrown a few tools, still miss fires.
Spark seems good with the plug out and grounded on the block. What else should I test and or try...
View 1 Replies
I have a 2001 golf with a 2.0 AVH engine. I recently replaced the coil-pack and was very pleased that the engine was running better, the only problem was the mpg was still kinda low in the 24-5 range when it used to be 29.
I tried to do a compression test but I didn't prepare properly, I thought you left the coil pack plugged in and the fuel fuse. Now I have a CEL that *was* flashing saying cylinder one is misfiring though it has stopped flashing. I drove it 13 miles home and it did improve but its still running rough. Very reminiscent of when my bad coil pack was still in there, a real lack of power.
So I have to ask, what can I do from here? Have I damaged my coil pack or cylinders? Will this likely go away on its own? Is there anything I should do?
View 4 Replies
Changed the spark plugs now I have misfire in cylinders 3 and 6. Do I change the spark plug wires or the coil pack?
View 5 Replies
Had a misfire in cylinder 1 so I put new plugs and wires. Still misfired. Changed fuel injector. Still misfired. Changed ignition coil and misfire on cylinder 1 is gone now cylinder 2 and 3 are misfiring. I double checked wires and they are properly installed.
View 11 Replies
