Isuzu - Axiom :: 2002 - Check Torque On Demand Light Flashing
Nov 2, 2013
We had the transmission rebuilt on Oct 1, 2013. Since then the check TOD light has flashed steadily. The transmission guys could get no codes on their equipment. We took it to another mechanic who replaced the speed sensor, light still flashed so he took it off. Finally found a way to get some codes which indicated neutral safety switch. He tried that, light still flashed, part removed. Tranny was leaking some fluid, so back to transmission shop. They had it for a week, fixed the leak, but could find nothing wrong with TOD, even from ATSG, so we took the car back.
View 3 Replies
Advertisement
2002 Isuzu Axiom screeches when turned on. If AC on, AC works fine but car screeches almost all the time. Can hear me coming a mile away. If AC is off, car stops screeching once running a moment. My mechanic said more torque on serpentine belt when AC on so he changed serpentine belt a few months ago and currently belt appears to be moving fine. He says compressor operates fine. Started about 6 months ago right after new transmission put in at dealership under Isuzu warranty. Mechanic stumped and waiting for something to break.
View 6 Replies
I have a 2002 Toyota Corolla CE with about 115,000 miles.While I was traveling on the highway my car started shaking, losing power, and the check engine light started flashing. I drove a mile or two to a rest area because I didn't want to pull over on the highway. I had it towed home. It starts and idles, but I'm afraid to get it out on the road.
View 15 Replies
I have had a 2002 Prius since December of 2012, and it has been running fine since I got it; while it was in a wreck in May 2013 that has rendered both passenger-side doors and windows unusable, I have not seen that incident cause any other problems, and the car still runs perfectly fine. I am supposed to be driving from my current home state for a job soon, but about a week ago while I was driving on the interstate, the check engine light started flashing.
I was changing lanes and putting a good bit of pressure on the gas in order to pass someone that was going below the speed limit, putting my speed at around 80 mph when the check engine light started flashing. I started getting off of the interstate to find a place to stop and inspect things, but the light stopped flashing when I got down to around 45 mph on the exit ramp, and I was able to drive the rest of the way on the interstate without any trouble, even when I got in the 75 mph range again. The span of time between the light starting to flash and turning off again was probably about a minute or so.
View 7 Replies
Wife's truck- 2002 v8 limited explorer with 116k... Yesterday she calls and says the od light is flashing and the message center says check transmission. She drove it home then when I got home the light was off and all seemed ok. I am taking it to have the codes read and hoping that my mechanics scanner picks up a code.
View 2 Replies
1996 izusu rodeo had check engine light on got code for egr valve. Replaced it light when out drove fine all day. Stopped at grocery store came back out would not start ... Will crank over but will not start. did a obg (two) scan get a p1640 output A circuit fault code along with a 1460 egr code ....
View 5 Replies
This car has been giving me quite a bit of trouble lately. 04 Ford Taurus SES, about 97,000 miles on it. Just last weekend, it broke down on the highway. Found out the torque converter failed and needed to be replaced. I was suspecting that something was wrong with the transmission for a while now, because it would stutter sometimes when accelerating, and sometimes start shaking in the front when I turned it on. (It still stutters after having the torque converter replaced.)
Well now, a day after shelling out quite a bit of money to the dealer for this torque converter, the check engine light is on. I went to Autozone to check the codes, and they found P0300, P0305 (cylinder misfire) and P0316 ("crank sensor condition"). Is it possible the transmission is failing?? I found a bunch of complaints online about the transmission failing on the 04 Taurus. I'm trying to avoid more expensive repairs, but I don't want the car to break down on me again....
Also, a couple months ago, the check engine light went on a few times, but always went off within a day or two. Never did get it checked out because it didn't stay on long enough.
View 18 Replies
I have a 1998 expedition 4.6 4x4 check engine light on od light flashing sometimes checked it and got p1747 code i was told epc solenoid or short on trans wiring. I already dropped the trans pan, looking for a step by step easy way to diagnose and find the short or if i need to replace any of the solenoids. I have voltmeter and taste light....
View 3 Replies
I've got a 2006 B9 with about 64,000 miles. Just a bit ago my check engine and ABS light came on, along with my cruise light flashing.
After researching a little bit on the forums and couldn't find an answer, I took it into the dealer, to which I was told that there was a bad oil pressure sensor for the right-hand side of the motor. I had them replace it out, and less than 20 miles down the road, the same lights appeared on my instrument cluster, and I took it back to the dealer. They informed me that there was now a bad sensor on the left hand side that would be another $380. I scheduled an appointment for later next week, and had them reset the error.
On the same day, about 2 hours later the lights reappeared on my dash, and I took the car over to a local parts store, where I used their scanner and the car now spit the following errors:
Camshaft position actuator A - Bank 1 timing over advan.
Camshaft position actuator A - Bank 2 timing over advan
Cam/crankshaft pos. correlation sensor A - Bank 2
Cam/crankshaft pos. Correlation sensor A - Bank 1
Camshaft position actuator A bank 1 timing over - advan
Camshaft position adctuator A bank 2 timing over -advan
Cam/crankshaft pos correlation sensor A - bank 1
I reset the codes, and waited another day for the lights to reappear on the dash. Again, I rescanned the errors, and found the same top 5 codes that I listed above.
Is there something more major going on here with the computer?
View 5 Replies
Had an issue with "check" engine light turning on and "cruise" control light flashing, intermittently. Dealer said we had dirty oil contaminating some solenoid valves in the system but we had just done an oil change and do so every 3-5K (car has 170K). They recommended switching around the sensors and doing an "oil flush" with another oil change. The warning light problem hasn't recurred, in the past month, since we started giving the gas cap a few extra turns after a fill-up. We're getting ready to buy a new car and don't want to give what might be a serious problem over to the next owner.
View 6 Replies
I have a 2007 L.L. Bean Edition Forester. The cruise light is flashing and check engine light is solid. I am well into my retirement age and nearest dealer is about 2 hours away. Is this something that local mechanic can fix? He is very good, but not Subaru schooled. I'm afraid to drive it now.
View 2 Replies
Have a Volvo XC70 and LOVE it! Recently ETS light came on and Check engine has always been on, mechanics did not seem to worried in past. As of the last month seemed to be issue with thermostat... Car would warm to normal when idling and driving below 25 mph... once I accelerated needle would drop and thermostat would go to baseline... Could feel faint warm air, but was only getting cold air coming from vents... Thought it might be thermostat stuck open?
Called my trusted mechanic and he recommended going to a radiator specialist, felt he might not be able to solve. Went to new shop today, after dropping off at 8am when they opened and not hearing from them until 4:45pm, 15 minutes before they close... Car is fixed, or so they say. Hot air is indeed coming out of vents and needle is staying where it should without falling...
BUT, now there is a strange smell (sulfur"ish") coming from the engine, and the car is shuddering and vibrating, bucking almost when car comes to a stop and then accelerates. ETS light is back on and check engine is now flashing!?! Tried going up hill on the way home and could not go faster than 20mph? None of this was happening before I took it in to the new shop today? They changed oil and oil filter and flushed radiater?
View 8 Replies
2004 F-250 6.0 Turbo Diesel W/ Torque Shift Transmission. Im having a problem with my Check Gauge light coming on and Tow Haul light flashing on my 04 F-250. I got a Transmission Fluid Temperature Sensor from my local Ford Dealership. They also said i needed to replace the Transmission harness for this application because of an open circuit.
My questions are, Is Mercon SP the only ATF that can be used on the Torque shift transmission and do i really need to replace the harness or just the sensor? I have read up a little on this and so far everything say's drain the fluid, drop the trans pan, swap out the sensor, replace the trans pan (torque setting is 11flbs I believe, correct me if I am wrong, replace with Mercon SP ATF and your good to go.
View 10 Replies
Friday I pulled my steel gn 3 horse trailer about an hour each way. with the horses it weighs right at 7000 pounds. no issues. Saturday morning I drove to town, no issues. Saturday evening, I got in it to run down the road and about 2 miles from the house, the check engine light came on and the tow haul light started flashing and the temp gauge is dead. drives and shifts normal, tow haul button still functions. Truck is stock except for an EGR delete. No tuner, FICM was rebuilt. I had it on a battery minder before I left and was thinking about pulling the batteries and letting it sit for a while to see if it clears. Scan Gauge II shows no codes.
Sunday: So I let it sit all night, batteries connected and it was completely normal this morning. will see what happens when I drive it to work tomorrow
Later Sunday evening: So I just took it out for a test drive, went a couple miles down the road, shifting normal for a cold start. Temp gauge is working, just as I am almost back home. 5 miles at the most, temp is coming up to normal, gauge goes dead and check gauge light comes on and tow haul starts flashing. I think it might be the sensor.
This morning: I got about 6 or 7 miles from home, trans just got up to temp, pulling up a hill, it shifted out of overdrive, tft gauge went dead, check gauge light came on and the tow haul light started flashing. still shifts like it always has and the tow haul button still functions.
I am thinking it is just the temp sensor. Truck has 159k on it.
View 13 Replies
Get in my car, try to start it and BAM it hits me. As I turn the key, the engine cranks up quick, kinda too quick, if you ask me. As I go to adjust my radio, I feel my car start to jump around and shake pretty rough. As I look at my gauges, I see my check engine light start to flash. So instead of trying to drive away, I turn it off and try to start it again. Same thing happens!! So I try it again and finally a normal start. Whew, I thought that was close. But oddly enough my check engine light comes on and stays on this time, no more flashing and the engine feels fine. What the problem could be? Is it safe to drive my car?
2000 Buick Park Avenue 3.8 auto....
View 13 Replies
I have a 2004 Audi A6 wagon that's got 105k miles on it. A couple months ago, the check engine light came on while I was driving it. While it was on, it was flashing and the car felt like it was shuddering, like there was not enough gas getting to the engine. Then the CIL stopped flashing. It happened several times during my short outing that day, but then it never happened again. Now the flashing CIL is back and the car feels the same way when it's happening. I took it to an auto parts store to get the trouble codes read and the guy said P0300 (random cylinder misfire) and P0305 (cylinder 5 misfire) came up.
View 18 Replies
As the title says, my CEL goes on and flashes too.
I've read up a bit on why the CEL comes on/flash and it says it has something to do with the exhaust system and if continue operating will damage the catalyst converter (which I don't understand since I'm a car dummy.
In addition, the engine vibrates like crazy. I can feel the engine vibrating when I'm inside the car as well.
I already got the car tolled to the dealership and they kinda just told me it might be misfirings and then they said they couldn't locate the problem. So my car basically has to stay there until they open again on Monday and hopefully they will figure out the problem/fix it under the warranty and call me back.
The problem arise late Friday night and I just did a 30K maintenance on Thursday. (but the car already has 43,000 miles on it).
View 35 Replies
If you get a f!ashing cel ,the next time you start it should it flash right away or can it go back to solid on cell? 02 Accent 1.6 130 k. What can be done to check the flex pipe for a leak? Can you spray water or what? The outside looks good. Also looks hard to check around intake manifold for leaks.
View 11 Replies
Yesterday out of no where my rio started to misfire so i immediately took it into autozone to have it checked. when doing so the check engine light was on, but solid.
The tests came back with P0300, P0301, and P0302 or 3. I cant find the papers, but its 3 cyns that are misfiring. The guy at autozone suggested i try changing out the plugs first since its cheaper and has been known to fix this issue.
The second I bought the plugs I went home and changed them out. once finished i started up the car and not only was the car still misfiring, but the check engine light is now flashing... I did notice one thing when changing the plugs.
If facing the engine the second coil from the left had a bit of what looked to be rust. i was able to wipe it off with ease. What my next move should be?
View 9 Replies
Let me start with some background. 2001 B5.5 Passat Sedan 1.8T 5spd Completely Stock 156,000 miles. So, tonight i head for the grocery store about 5 minutes up the street. I get about half way there, when I notice that the check engine light is flashing. I ease off the gas, and coax it to the next light. At the light, the car feels like it might stall out, and the car seems to shudder, and I notice that the shudder is connected to the RPM of the motor. Meaning, if i rev the motor the shudder gets faster.
I manage to coax the car home to my driveway, and I leave it in a position easy to be towed. So, i figure that I will leave the car running, and look under the hood, but as soon as I open the drivers door, i can smell something burning/smoldering. I shut off the engine, and carefully open the hood. I find no smoke or fire, but I see that the downpipe (or whatever pipe the exhaust coming from the turbo leaves through) is glowing red hot.
I am not sure what happened. The car gave no other obvious symptoms. The other things I should mention though, are that I change my own oil. Always Mobil 1 with a Audi or at least german filter. However, my father was the original owner, and for the first 60k he used conventional oil. The turbo has always been strong, and seemed to deliver full boost. I do not know if it is still boosting in light of recent events.
For the last few weeks, the check engine light has been on and off. My mechanic scanned it a few times, and told me that it was the "Air Injection Pump Code". My understanding is that this system basically divers exhaust gas into the Cat when the car is warming up. If its not working properly, then it is just a emission problem.
I should also mention, that the car has recently been leaking a little bit of water when there is a hard rain storm. On Saturday, I took the rain tray cover off, checked the Pollen Filter, and removed the battery in order to clear out the drain plugs under the battery tray, and the brake master cylinder. As I write this, I begin to wonder if its possible that something just went very wrong with the Air Injection System.
View 12 Replies
this morning my 02 decided to turn the ABS light on, and start bouncing the speedometer. plus, the OD light is flashing when stopped with foot on the brakes, but the trans is shifting fine.
nothing changed on the truck except almost 3 inches of rain fell last night.
will AE tell me if the VSS is going bad?
View 6 Replies
