Impala - Chevrolet :: Sputter And Jerk When Start To Accelerate Past 25 Mph And Get Around 2000 Rpms
Jun 15, 2011
I have a 2002 Chevy Impala driving it in the city of Chicago. It's recently had the oil changed, and the transmission fluid flushed and filter replaced. This car was mine before I went off to school, and I meticulously maintained it for three years, and then my step sister inherited it. She drove it for two years, and then it sat in the driveway for a year and a half. It's got about 175,000 miles on it.
Problem: Every time I start to accelerate past 25mph and get around 2000rpms, the car starts to give out, sputter and jerk. It starts to drop off right when it should be shifting to second gear. When on the highway, even if I floor the gas peddle, it won't accelerate normally, but instead just crawls slowly to higher speeds.
It will eventually reach the higher speeds, but it takes about 5-10 minutes for it climb up from 25mph. I don't know enough about this level of car trouble to make a diagnosis myself, and would like an estimate of the cost for repairs. Also the car is getting around 19mpg on the highway, which I need to improve if I'm going to survive the $4.50/gal of Chicago gas. I'm hoping that fixing this problem will take care of that as well.
View 3 Replies
Advertisement
My Impala hesitates at 2,000 RPMs At every speed level. My mechanic and the Chevy dealer can't figure this out.
View 1 Replies
Why does my 2000 chevy impala whistle when i accelerate? it also seems to shift hard.
View 10 Replies
I have a 2011 Chevy Impala. When accelerating from a stop it will frequently stutter then jerk forward. The first time this happened I thought someone had rear-ended me.
I've been to the dealer several times about this however they say they cannot isolate the cause. More importantly I can't seem to get the vehicle to repeat this problem when I've brought it to the dealership.
View 4 Replies
i'm having a hard time starting my 2000 chevy impala. it orginal had a security plug on it. i had it removed. to start when i turn on the turn signal there was a noise, the odometer when blank, the air bag symbol appeared. the next time i tried to start the car it would do the same thing but wouldn't even turn over. sometimes you can turn the key on and wait 30 seconds, step on the brake and it may start. i have continued to try for up to 3 minutes. if you put on jumper cables sometime it will start. what is the problem?
View 2 Replies
I have a 2003 Mach 1 Mustang, ( 4.6 DOHC 32 Valve)....
When I start my car in the morning. Idling the car sounds normal and perfect with my SLP exhaust. But when I start to go on my merry way, when I’m in 1st and 2nd gear and I accelerate past about 2.8K rpm's. I hear a really quite noticeable pingy/tingy sounds from my engine (Yes sounding like that annoying AMMCO commercial with people making noises). This will continue for a little while when i get into my normal running temperature, the sound isn’t as "Loud" so to say but still present.
I can comfortably say that there is nothing loose within the engine compartment. My spark plugs are tightened to the proper amount. I experience no performance lost as well. This has just been a nuisance since I have purchased the car, it currently has almost 60k mileage and has followed the proper maintenance.
View 9 Replies
I have a 2000 Chevy Impala and it seems that every now and then when I try to start the car the security feature activates and I have to wait 10 mins to try to start it again. On some occasions when the 10 mins are up and I try to start it the feature reactivates and I wait another 10 mins. This actually happened on a ferry ride and I held up the offloading of vehicles. My question is, Will a remote starter installation alleviate this issue? If not. What can I do?
View 5 Replies
I have a 2006 chevy malibu 2.2 ecotec 4 cyl with ~130,000 miles and i am experiencing the following symptoms:
Car will not rev past 4000 RPMs or go over 70mph. I do have a check engine light with the following two codes: P0068(throttle position) and P0420(cat efficiency)
My question is instead of just replacing the cat where can i take my car (i live in tulsa, ok) to have the cat and the sensors checked before they are written off as bad?
View 19 Replies
i've got a 2000 chevy impala 3.4 v6 E. runs great once it starts, but lately that takes a lot of cranking. it's getting spark. it's got a new alternator, battery, starter, plugs and wires (and i checked for spark already) I think it's a fuel issue but don't know where to start looking because it has no other problems. there's no smoke or noises, no misfires, or hesitations. i put in a new fuel filter. i have heard that it could be the fuel pressure regulator or maybe even a leak in the line that's causing it to not get pressure. i can't hear any sort of fuel pump sound (maybe i'm deaf) is there a way to check this without a gauge? i simply don't have one and don't have the money to take it to a shop. p.s. i recently replaced both o2 sensors, but i can't see how that would effect the starting. pump, hose, regulator, fuse?
View 4 Replies
while at stop in netural, reve engine, it seems to want to stall after it hits higher rpm?
View 1 Replies
I have 2000 chevy impala with a 3800 series 2 engine with 170,000 miles on it. I have major oil leak which starts leaking when the car is running, i cannot see from the top and when i am underneath the car , I cannot see far enough up in the there to see where it is leaking, It is not coming from the seneding unit or the oil pan,,when the car is running it just pours out oil.
View 3 Replies
My son has a 2000 Impala which will not start if it has been warmed up and then turned off for 30-40 minutes. If you turn it off and wait 15 minutes it will start every time - wait much longer and you are stranded. The starter sounds normal and you would think it is going to start but it won't. The car sat at the dealership for 2 weeks and they couldn't solve the problem. If the car is cold it starts every time.
View 10 Replies
How do you shut off the CHANGE OIL LIGHT on a 2000 Chev Impala?
View 5 Replies
I have a 2004 3.5L Santa Fe with about 170k miles on it.
Runs great. I am going to change the timing belt here in the next week or so.
I have started having an issue where going into second gear it will jerk, almost like sputter. Does not do it all the time. Seems like a sensor or computer issue because the rest of the gears shift smooth. And if was a problem with the internals of the transmission I would think it would always do it and never go away.
What the issue could be since I am already going to be digging deep into the vehicle might be worth replacing more parts, what it is.
View 7 Replies
So I replaced my turbo about 2 years ago give or take and maybe 15-20k miles on it since. The last few weeks my car has been running some what weird so i decided to bring it to the shop. The guy thinks its my turbo but its hard for me to believe. Here are the symptoms it was having..
1) Lose of power
2) When I was on the high way i would floor it and it just wouldn't go. It would accelerate after 60 mph and it would almost be at a stand still. A few times it almost lost power completely and i had the pedal to the ground and it was decelerating.
3) When I would drive the car would sputter and jerk like almost it wasn't getting gas.
4) After a overnight where it was shut off, the next day i would go turn it on and it would barely turn over and it would be rough for a few seconds.
5) The exhuast/muffler after accelerating would pop
6) I don't hear my turbo spooling as loud and as much as it use to.
Could this be some sort of sensor or even the fuel pump? I feel that it wouldn't have some of these issues if it was the turbo compared to something else.
View 3 Replies
I just replace the engine in my car and I had new plugs and wires put in as well. Ever since the new engine, the car doesn't go up hills well and it is very sluggish from a stand still position. As long as I am driving on a flat surface I am good once I get up speed. I went to autozone and I got a P0300 code. Is this a bad ignition coil or maybe a clogged catalytic converter?
View 10 Replies
My 2000 impala starts when cold, runs for 10 min and dies, i found its losing spark when warm, i changed the coil packs, control module and cam sensor and have had no changes, it dies, and doesn't start, only turns over, i leave it for 30 min er so and it starts , runs for 10 and dies....
View 4 Replies
I have a 2003 ranger with 2.3. I drive it daily but it has started to sputter and jerk. The truck has 94000 on it and I bought it new. It sat for over a year but has been driven every day for the last year. It started a couple months ago but would just do it for a second, now I cant drive it on the highway. I think it might be injectors but how do I know for sure?
View 12 Replies
2009 Impala, 54k, factory installed remote start will no longer start the engine.This problem just started with both remotes.When used in close proximity of the car this is what happens: 1st-attempt-I hear a short humming noise and lights flash, 2nd-attempt a click and lights flash, 3rd attempt (and there after)-no sound and no flash of lights.The remote lock/unlock feature with horn beep and lights flash works fine on both remotes.The car starts every time by key with no problem.Any thoughts of what may be wrong?
View 5 Replies
I have a 2000 Impala with a 3800 V6 series 2 with 165,000 miles. The only code I had was a P0300 Multiple random misfire that occured off and on at first, Worse in the city Better on Highway. It would start running on half the cylinders and bogged down, with the check engine light flashing, after getting onto the highway it would straighten itself out at first. I thought i had water in the gas so i ran some heat through it. straightened out for a day then happened again so I thought maybe a should run some premium gas in it, The car ran like total crap until the premium was gone, so i thought maybe it's running too rich, I put 87octane in it and it ran great for a day or two, then it gradually got worse to where it would not straighten up on the highway, tried to die at stoplights and i had to drive it with 2 feet to get it home and park it. I've replaced the battery, spark plugs, wires, ICM checked good, coil packs are good, replaced fuel Pressure regulator, looked for arcing on the spark plug heat shields and it will not start. It turns over but doesn't try to ignite and when I get the slightest rumble of ignition, it backfires up through the manifold and I see a puff of gas or light smoke by the exhaust manifold.
The car had a vacuum leak around the intake manifold cover gasket and a leak on the fuel rail. I pulled the fuel rail off my impala, snugged up the rest of the intake bolts then disassembled the fuel rail, flushed it out and cleaned the injectors the best i could, then reassembled it. before i re-installed the fuel rail I hooked it up to the fuel lines outside of the engine and tried to start the vehicle. all injectors had a nice spray pattern. So i installed the rail and it still didn't start but it had more combustion than before although it's still backfiring like before. Checked the fuel pressure by turning the key on and the fuel pressure went to zero very fast. I blew the rail out with air so to make sure i didn't damage the regulator I replaced it with the old one, ran the test again with same results, so i reinstalled the new regulator. I performed the fuel pressure test a few more times while moving the fuel hoses and when i moved the back supply line the vacuum loss stopped then dropped to zero when i let off of it. So I replaced the fuel line connector and O-rings on the injectors. It no longer has a vacuum leak.
I cleaned the EGR Valve out and had no luck there, then I removed the Idle Air Control Valve-pushed the pintle in, re-ionstalled it and WooHoo! it started! Although it still ran like crap with the same random misfire I was still happy to hear it start.I pulled the plugs on it to do a compression test and all 6 cylinders have between 180-190psi so the engine is in good condition mechanically. I installed new plugs before getting the car restarted and when i removed them for the test they were covered in thick black soot after running for roughly 15 minutes max.
I have (2) 2000 Chevy Impala's so I've swapped sensors from my wifes car to see if it would fix it. I've tested the following MAP, MAF, IAC, coil packs and ECM. None of these made the car change. I believe it is a timing chain because the car has never had a new timing chain and is way overdue, but I haven't had a code for a crankshaft position sensor. Can the timing chain be bad without throwing a code? It's not out of time enough to change the valve timing because I had a good compression test but its not firing right and still has the multiple random misfire. I have not checked or received a trouble code for o2 sensors, crankshaft position sensor or cam sensor. Something has the timing retarded and is dumping extra fuel into the engine because my new plugs looked like they were in the engine for a year.
View 4 Replies
I have a 00 impala w 4t65e tranny I believe I have a p1811 code of hard and long shifting. I also need both cv axles replaced. If i replace the axles and have then dropped. Is it possible with the pcs going out, i would be able to drive 600 miles both way to a family thing without getting stranded.
View 3 Replies
