Impala - Chevrolet :: 2008 Hesitates At 2000 RPMs
Dec 30, 2013
My Impala hesitates at 2,000 RPMs At every speed level. My mechanic and the Chevy dealer can't figure this out.
View 1 Replies
Dec 30, 2013
Advertisement
Impala - Chevrolet :: Sputter And Jerk When Start To Accelerate Past 25 Mph And Get Around 2000 Rpms
I have a 2002 Chevy Impala driving it in the city of Chicago. It's recently had the oil changed, and the transmission fluid flushed and filter replaced. This car was mine before I went off to school, and I meticulously maintained it for three years, and then my step sister inherited it. She drove it for two years, and then it sat in the driveway for a year and a half. It's got about 175,000 miles on it.
Problem: Every time I start to accelerate past 25mph and get around 2000rpms, the car starts to give out, sputter and jerk. It starts to drop off right when it should be shifting to second gear. When on the highway, even if I floor the gas peddle, it won't accelerate normally, but instead just crawls slowly to higher speeds.
It will eventually reach the higher speeds, but it takes about 5-10 minutes for it climb up from 25mph. I don't know enough about this level of car trouble to make a diagnosis myself, and would like an estimate of the cost for repairs. Also the car is getting around 19mpg on the highway, which I need to improve if I'm going to survive the $4.50/gal of Chicago gas. I'm hoping that fixing this problem will take care of that as well.
Impala - Chevrolet :: 2000 - Hard To Start?
i'm having a hard time starting my 2000 chevy impala. it orginal had a security plug on it. i had it removed. to start when i turn on the turn signal there was a noise, the odometer when blank, the air bag symbol appeared. the next time i tried to start the car it would do the same thing but wouldn't even turn over. sometimes you can turn the key on and wait 30 seconds, step on the brake and it may start. i have continued to try for up to 3 minutes. if you put on jumper cables sometime it will start. what is the problem?
View 2 RepliesImpala - Chevrolet :: 2000 - Starting After Lots Of Cranking
i've got a 2000 chevy impala 3.4 v6 E. runs great once it starts, but lately that takes a lot of cranking. it's getting spark. it's got a new alternator, battery, starter, plugs and wires (and i checked for spark already) I think it's a fuel issue but don't know where to start looking because it has no other problems. there's no smoke or noises, no misfires, or hesitations. i put in a new fuel filter. i have heard that it could be the fuel pressure regulator or maybe even a leak in the line that's causing it to not get pressure. i can't hear any sort of fuel pump sound (maybe i'm deaf) is there a way to check this without a gauge? i simply don't have one and don't have the money to take it to a shop. p.s. i recently replaced both o2 sensors, but i can't see how that would effect the starting. pump, hose, regulator, fuse?
View 4 RepliesImpala - Chevrolet :: 2000 Stalling After Hitting Higher RPM
while at stop in netural, reve engine, it seems to want to stall after it hits higher rpm?
View 1 RepliesImpala - Chevrolet :: 2000 - Major Oil Leak When Car Is Running?
I have 2000 chevy impala with a 3800 series 2 engine with 170,000 miles on it. I have major oil leak which starts leaking when the car is running, i cannot see from the top and when i am underneath the car , I cannot see far enough up in the there to see where it is leaking, It is not coming from the seneding unit or the oil pan,,when the car is running it just pours out oil.
View 3 RepliesImpala - Chevrolet :: 2000 - Intermittent Starting When Warmed Up
My son has a 2000 Impala which will not start if it has been warmed up and then turned off for 30-40 minutes. If you turn it off and wait 15 minutes it will start every time - wait much longer and you are stranded. The starter sounds normal and you would think it is going to start but it won't. The car sat at the dealership for 2 weeks and they couldn't solve the problem. If the car is cold it starts every time.
View 10 RepliesImpala - Chevrolet :: 2000 - How To Shut Off Change Oil Light
How do you shut off the CHANGE OIL LIGHT on a 2000 Chev Impala?
View 5 RepliesImpala - Chevrolet :: 2008 - Won't Shift Out Of Park
I have a 2008 Chevy Impala. I've owned it for 14 months and put about 12,000 miles on it in that time. It's had basic servicing (rotations, oil, oil filter, cabin filter, etc. changes). It hasn't given me problems---but suddenly I have one and I'm not sure how major it is.
I made a drive from New York to Western Mass yesterday...couple hundred miles, but nothing huge. It drove fine all yesterday after I arrived...again, no problems. This morning, I went to start it...everything's okay. But then I went to shift it out of park...the button will not depress. I restarted a few times...no luck. I kept trying to depress the petal to shift it; I couldn't even shift it into neutral when not started. I am not sure what in the world is going on.
I've read numerous forums on this---it seems to be a common problem with these cars. What's not so clear is what to do with this. Responses range from---stick a screwdriver into some hole all the way to just go on and junk the car, it's useless. That's why I am coming here to get clearer guidance on resolving this problem, hopefully in an economical way.
Impala - Chevrolet :: 2008 - Hood Won't Stay Up
I have a 2008 Chevy Impala that I've owned for going on six months. It's treated me very well. I'm just now getting ready to give it a nice wash/interior cleaning this evening, but I noticed while cleaning under the hood just now that I cannot get the hood to stay up on it's own. I'm not sure what the issue is. I keep nudging it gently, but that's not working. As recently as yesterday I had the hood up when I was checking the oil...it stayed just fine.
Of course, the pre-2014 Impala generation has hoods without the manual supports. So what might the problem be here? I figure this car is a little new to be having a problem like this.
Impala - Chevrolet :: 2000 3.4L - Sluggish From Standstill Position And Does Not Go Uphill
I just replace the engine in my car and I had new plugs and wires put in as well. Ever since the new engine, the car doesn't go up hills well and it is very sluggish from a stand still position. As long as I am driving on a flat surface I am good once I get up speed. I went to autozone and I got a P0300 code. Is this a bad ignition coil or maybe a clogged catalytic converter?
View 10 RepliesImpala - Chevrolet :: 2000 - Dies When Warm After Running For 10 Minutes
My 2000 impala starts when cold, runs for 10 min and dies, i found its losing spark when warm, i changed the coil packs, control module and cam sensor and have had no changes, it dies, and doesn't start, only turns over, i leave it for 30 min er so and it starts , runs for 10 and dies....
View 4 RepliesImpala - Chevrolet :: 2008 - Ignition Switch Failure?
I am the (once) proud owner of a 2008 Chevrolet Impala. I have owned the car for one year, putting only 12,000 miles on it (was 109,000 when I bought it.) The car has run quite well—I have not had any problems out of it (unlike the 1999-2005 generation Impalas). But, as many of you may have heard, GM had some massive recalls as of late. Many of the cars have had fatal ignition switch failures. Basically every single Impala in the last (my) generation has been recalled.
Take any other keys/paraphernalia off of the chain—basically, just insert the key into the ignition, unattached to anything. This is the fix for the time being, apparently—until they can get ignition switches for however many hundred thousand Impalas they have to fix.
I am about to make a 3 hour drive. Now, that wouldn't be the longest drive that I have made in this car (and I cringe at the idea that, driving 17 hours with a bunch of crap hanging off of my chain, that my car easily could have been one of the unfortunate ones.)
Now that I know that I cannot be sure of the safety of my vehicle, I need to know what to do in the case of an emergency. I want to know what exactly the situation of an ignition switch failure entails...basically, what happens to my car and my ability to control the car. Lastly, I need to know what to do if this happens.
Impala - Damage - Chevrolet :: 2008 - Scratches All Over - How To Paint It
My car has fairly deep scratches on the trunk, roof, and hood. It's a red, 2008 Chevy Impala. I'd take pictures---but it's too painful. There are numerous thin scratches on each of these surfaces. I'm going to take it to a body shop to get an estimate, but I know I am probably not going to like what I hear. No, my insurance does not cover this (I only have liability). So...Am I going to need a completely new paint job?
View 19 RepliesImpala - Chevrolet :: 2008 - Hard Shifting After Start Up
My '08 Chevy Impala (116,000 miles) has had a recurring issue over the past few months. After I have first started it, and for maybe the first 15 minutes it is running, it has been 'shifting hard' from 1st to 2nd gear. Basically, the engine revs much higher than it normally would and it 'thunks' into second gear. If I intentionally push the gas slower it does not happen. The guys who service my car (not Chevy) told me that my Transmission fluid level is fine.
View 2 RepliesImpala - Chevrolet :: 2000 Chevy Whistle When Accelerate / Shift Hard
Why does my 2000 chevy impala whistle when i accelerate? it also seems to shift hard.
View 10 RepliesImpala - Chevrolet :: 2000 3.8L V6 - Code P0300 Multiple Random Misfire
I have a 2000 Impala with a 3800 V6 series 2 with 165,000 miles. The only code I had was a P0300 Multiple random misfire that occured off and on at first, Worse in the city Better on Highway. It would start running on half the cylinders and bogged down, with the check engine light flashing, after getting onto the highway it would straighten itself out at first. I thought i had water in the gas so i ran some heat through it. straightened out for a day then happened again so I thought maybe a should run some premium gas in it, The car ran like total crap until the premium was gone, so i thought maybe it's running too rich, I put 87octane in it and it ran great for a day or two, then it gradually got worse to where it would not straighten up on the highway, tried to die at stoplights and i had to drive it with 2 feet to get it home and park it. I've replaced the battery, spark plugs, wires, ICM checked good, coil packs are good, replaced fuel Pressure regulator, looked for arcing on the spark plug heat shields and it will not start. It turns over but doesn't try to ignite and when I get the slightest rumble of ignition, it backfires up through the manifold and I see a puff of gas or light smoke by the exhaust manifold.
The car had a vacuum leak around the intake manifold cover gasket and a leak on the fuel rail. I pulled the fuel rail off my impala, snugged up the rest of the intake bolts then disassembled the fuel rail, flushed it out and cleaned the injectors the best i could, then reassembled it. before i re-installed the fuel rail I hooked it up to the fuel lines outside of the engine and tried to start the vehicle. all injectors had a nice spray pattern. So i installed the rail and it still didn't start but it had more combustion than before although it's still backfiring like before. Checked the fuel pressure by turning the key on and the fuel pressure went to zero very fast. I blew the rail out with air so to make sure i didn't damage the regulator I replaced it with the old one, ran the test again with same results, so i reinstalled the new regulator. I performed the fuel pressure test a few more times while moving the fuel hoses and when i moved the back supply line the vacuum loss stopped then dropped to zero when i let off of it. So I replaced the fuel line connector and O-rings on the injectors. It no longer has a vacuum leak.
I cleaned the EGR Valve out and had no luck there, then I removed the Idle Air Control Valve-pushed the pintle in, re-ionstalled it and WooHoo! it started! Although it still ran like crap with the same random misfire I was still happy to hear it start.I pulled the plugs on it to do a compression test and all 6 cylinders have between 180-190psi so the engine is in good condition mechanically. I installed new plugs before getting the car restarted and when i removed them for the test they were covered in thick black soot after running for roughly 15 minutes max.
I have (2) 2000 Chevy Impala's so I've swapped sensors from my wifes car to see if it would fix it. I've tested the following MAP, MAF, IAC, coil packs and ECM. None of these made the car change. I believe it is a timing chain because the car has never had a new timing chain and is way overdue, but I haven't had a code for a crankshaft position sensor. Can the timing chain be bad without throwing a code? It's not out of time enough to change the valve timing because I had a good compression test but its not firing right and still has the multiple random misfire. I have not checked or received a trouble code for o2 sensors, crankshaft position sensor or cam sensor. Something has the timing retarded and is dumping extra fuel into the engine because my new plugs looked like they were in the engine for a year.
Impala - Chevrolet :: 2000 - Code P1811 / Hard And Long Shifting
I have a 00 impala w 4t65e tranny I believe I have a p1811 code of hard and long shifting. I also need both cv axles replaced. If i replace the axles and have then dropped. Is it possible with the pcs going out, i would be able to drive 600 miles both way to a family thing without getting stranded.
View 3 RepliesImpala - Chevrolet :: 2008 - Vibrations And Squeaking Sound From Hood
I've owned a 2008 Chevy Impala for about 7 months. It's at about 115,000 miles. It runs great...haven't had any problems out of it. So far. But there are a few things that concern me.
When I start the car, I hear this squeaking noise under the hood. I do not always hear this---it seems as if it may be tied with cold weather, like it's something that only occurs in the morning. But regardless, it seems abnormal. It subsides after a few minutes. The other thing I am noticing is that normally within the first 10 or 15 minutes of operation, if the car is at a stop light I'll hear some strange humming accompanied by vibrations. Sometimes the lights will flash faintly when this happens.
When I first purchased the car, I had a mechanic check it out. The engine, transmission, radiator, etc. were in excellent condition. I'm hoping that this is not anything serious, but I figure these are still sounds that I should not be hearing with a car in good condition.
Impala - Chevrolet :: 2008 - Interlock Shift Button Would Not Depress
I have a 2008 Impala that has been having interlock shift issues for about a week. The interlock shift button would not depress. I was able to remove the center console and take a look at some of the wiring. It there's a bundle of wires and there is a black wire that appears to be severed. From what I've read, this is a common problem with the Impala models from 2006 through 2008...it should have been a recall, but for some reason was not. How can I do a low-cost DIY repair on this that's going to be solid and prevent recurring problems?
View 3 RepliesImpala - Chevrolet :: 2008 - Parking Lights On The Entire Day / Car Just Would Not Start
I drove to work this morning and parked my car (around 10:30AM). I return to my car at about 9:00PM. I approach it trying to unlock it using my remote. I keep hitting the button as I approach...it does not work. I unlock it manually and get inside and put the key in ignition...absolutely nothing happens. No lights, no dashboard, no...nothing.
Then I remember...I left my parking lights on the entire day! That must be what's wrong...
I go and grab some portable jumper cables and...boy did I kill some time trying to elicit a reaction. When I hooked it up, the car came alive completely...it just wouldn't start no matter how long I let it sit. I would simply hear a single click. So, I went a grabbed another set of portable jumpers and....same exact thing. By the time the tow guy came around, he tried it with his portable cables as well and...same exact thing.
I am trying to figure out what in the world is wrong. I replaced the battery one year ago, when I had trouble starting it. So...the battery is new and, by all appearances, in good condition. Outside of that, no history of starting problems whatsoever...which is what makes all of this so incredibly confusing.