Ignition :: Quits Firing - Plugs Are Not Receiving Any Spark
Sep 25, 2011
I was driving along, and my loyal Loyale quit firing. I can crank the ignition, but the plugs are not receiving any spark. There is fuel hitting the chambers. . . Since there wasn't any spark at the plugs, I tried the distributor and rotor area. The D&R are both very new, and looking good. There isn't any power reaching the distributor cap/rotor. . . So I turned to the coil. I had a friend test with a multimeter, and we determined that the coil was receiving electricity, but was not sending any. So at this point, I'm under the impression that the coil is bad. I ordered a new coil from the local parts store, and dropped it in. No change in the above scenarios. The new coil has "USE WITH ELECTRONIC IGNITION" printed on it. I don't know a lot about vehicles, but I thought that the Distributor/Rotor system was a Mechanical Ignition system. Was I given the incorrect part? Is the new one defective? Is there somewhere else that I need to be focusing attention? Oh, we also checked the fuses. They're good as well. Also, the Timing belt is not broken.
View 3 Replies
Advertisement
I was having some problems and one of my friends told me to post up here before I went and saw my mechanic. So my car isn't starting (its a 06 r32). Now I've gone through a whole list of things and what I have worked out is that it is the spark plugs not firing (none of them are) although they are all brand new and were working not too long ago.
Battery is fine and fuses look good no warning symbols on the dash so I'm at a bit of a loss as to what it could be. Relays? Coils?
View 5 Replies
Today I ran into a problem while i was changing my spark plugs ...two of the plugs were completely covered in oil. I mean oil was literally dripping off those plugs. I have a Passat 1999 2.8L V6. What could be wrong.
View 3 Replies
I am changing my own spark plugs for the first time. I have a spark plug wrench, dielectric grease, anti-seize compound etc.
I have a Haynes manual for my 2002 Toyota Corolla. The book was written before Irridium plugs were used. Should I tighten the spark plugs to the same torque specifications as regular plugs? The book says 158 inch pounds. How do I know I have tightened them to the right amount?
How do I avoid cross threading the spark plugs? What happens if you cross thread the spark plugs (assuming the car seems to be running fine)? Would I need a new engine or expensive repair when it is time to replace the spark plugs again?
View 19 Replies
I have a '97 Hyundai Elantra (That has been turned in to a Dirt Race Car) anyway the car will idol for an hour fine. When we take it on the track it will run 4 or 5 laps fine then we take it in the pits shut it off for an hour and then go back on the track and on the 2nd lap it will quit and will not start it will crank but their in no spark also the dash lights no longer work. After the cars sits for a couple hours it will start back up and idol fine. We have replaced the ECU/ECM relay as we thought that was the problem but the symptoms remain the same. We have checked fuses and don't seem to find a problem our next step is to replace the ECM....
View 8 Replies
Ford Explorer Sport 2000, Number 1 spark plug has miss firing already replaced spark plugs wires and coil pack what more can i do to get spark from number 1 to spark and took garden hose to listen to injectors clicking when running. any other part for spark.
View 1 Replies
Al right i have a 94 ranger 4.0 4x4 auto 186k ... The truck has new bosch double plat plugs gaped .054, new wires, MAF, TPS, FPR, O2 sensors, ECTS and I checked the intake air charge sensor and is fine ....
My issue is cylinders 4,5 and 6 dont fire... the coil is sending a spark, i can pull the plugs one at a time and watch them fire (strong blue spark)... All fuel injectors do not leak and spray a perfect cone out of all 4 holes and noid light test is good ...
The truck runs like crap back firing and no power under 4k and i can pull off all 3 wires for bank one and it make no difference and when i unplug the injectors no more back fire....
View 14 Replies
I am having a problem where my spark plugs keep going out. I changed all the plugs, wires and coil pack on my 2001 Windstar and within a few months my van was running on 4 or 5 cylinders instead of 6 and this isn't the first time it has happened.
View 14 Replies
I have a 2001 saturn sl 2 and I noticed some oil around all the spark plugs. The engine seems to be loosing oil a little bit as well, about a quart a week. Its not buring it or leaking that I noticed.
View 2 Replies
'03 Solara 4 cyl, 135K repl. Fuel pump, 45# press ok, NO scan tool code(s), turns over fine, no spark 2 plug. Started/ran fine before fuel pump change.
View 10 Replies
I was thinking about change my spark plugs on friday so today I went to check the ones the car have open the hood took the engine cover out and the ones on the sides, I see 6 wires 4 going to the left side(air intake side) and 2 going to the right side (where the oil fil cap is) so I say think this should be the spark plugs wires. I take one of the left side wires out and is cover in oil so I keep taking the other out one by one and all of them have a lot of oil I can't even see the sparks plugs. All the wires have numbers on top 1 to 6. I say this have to be the wires cause I don't see any other place where the plugs can be located at. The car is a 99 v6 fwd...
View 7 Replies
I would like to have a look at the condition of the ignition plugs in my V8 Phaeton.
According to the service plan, it's already time to change them and it also seems that the car has lost some power when accelerating.
Is it even possible to change them with the 'usual' knowledge (knows how to change a tire and so on) or should I better go to a professional.
View 24 Replies
Had issues with TBI, rebuilt. Had some starting problems after truck sat for 1 day or more, but would start after a few tries. At one point when it was particularly stubborn, starter lead vibrated off. Once reconnected, truck started, ran fine, but had some electrical humming & radio interference. The starting issue continued with some low rpm stumbling, when driving check engine light would come on at cruising speeds and go off 7-8 seconds after letting off gas.
Had 1 day lest week when I drove a bit more then normal (150+) but ran fine other then engine light. Next day started, but ran horribly rough with violent back fires. At one point stalled and would not restart. It looked and acted like it was flooding itself out and poor spark. Less then a year I replaced cap, rotor and coil. Now I have done all new plugs and wires. Now it appears I have no spark. I had been in the dash messing with the blower motor relay 2 days prior to the stalling and not starting.
Does the ECM control spark? Cant it go bad slowly? And if I had to do alot of cranking of the engine to get it to start, would that have any thing to do with it going bad?
View 14 Replies
I don't have a torque wrench. I just have a spark plug wrench. I changed my own spark plugs. I don't like taking them out and putting them back in. I'm not sure if I got the torque right. What should I do?
View 1 Replies
Bought my car three weeks ago. I was looking around under the hood and noticed that the color of the connector on the spark plugs is different. Two are grey and two are black, in alternating order. What's up with that?
View 5 Replies
I have a 2000 Jetta 2.8 VR6 (the 6-cyl) with 128k miles and I have oil on my spark plugs, only on one bank of the motor (the bank closest to the bumper, if that makes any difference). I am aware that it is most likely a leaking or worn out valve cover gasket, and I have a replacement and am prepared to replace it. What I need to know, and I can't find this exact part anywhere, is do I also need to replace the spark plug tube seals??? The gasket I ordered did not come with any tube seals, I can't find this part on any auto parts website at all, nor have I been able to locate anything useful on this, or any other, website. I know the 1.8 has plug tube seals, and they come with the gasket, but does the 2.8 also require tube seals? I imagine it would, but I just don't know.
View 2 Replies
I have a '63 Buick Wildcat that has been sitting for 17 years. It has 2 spark plugs stuck in the motor. I got the other 6 out with liquid wrench. The other 2 have been soaking in liquid wrench for 2 weeks and I have been using a 3/8 drive spark plug socket, but still unable to get them out. How to get them out?
View 9 Replies
I need to change spark plugs in my daughter's 2010 Tiguan but I have never worked on a VW before. How do I get to the spark plugs and what brand is recommended?
View 6 Replies
I can't get a single spark plug to come out of my 2009 Corolla S. I'm using a 3/8 ratchet with a 3 inch extension and a GearWrench 9/16" x 6" Magnetic Swivel Spark Plug Socket (3938D). Which is exactly what others have suggested. It feels like the socket is just spinning around on top of the spark plug. I'm kind of at a loss for what to do now?
View 10 Replies
I have a 2008 Camry, 2.4L, and used the spark plugs change DIY sticky and it seemed to go painlessly. However, after the new spark plugs, the car seems to idle rough. It has 95k miles, and I did the following in the same tune-up:
1. Changed Oil
2. Replaced Air Filter
3. Changed Spark Plugs
4. Cleaned Battery Terminals
5. Cleaned MAF Sensor
6. Cleaned plugs connecting to ignition coils
I used OEM Toyota plugs, and even called the dealer to see if the gap needed to be set. And they affirmed me that the gap is preset on these plugs.
View 2 Replies
All the oil leak out of engine after a oil change? and i have oil in the spark plug tubes
View 6 Replies