My 2005 Hyundai Elantra has 85,000 miles and we are having trouble with the gear shift. It will not shift into 1st from neutral but will shift into 1st from 2nd. We recently replaced the clutch (about 3 months ago). We are about to go on a road trip and are wondering whether we should get it checked out before hand.
View 9 RepliesI have a 2005 Hyundai Elantra with approx 155,000 miles on it(I don't know if that matters). The car started ok at first. When I put it into reverse, I noticed that it was really hard to move the gear shift(which it's normally really easy). I put it back in park and let it sit for a minute thinking it just had to warm up a bit more.
When I tried it again, it was still hard to shift, but this time when it got into gear I heard a loud clunk. This scared me, so I put it back in park and turned off the car. Now it won't start. All of my lights(headlights, dashboard lights, radio) come on, but the engine won't turn over.
I don't know if any of the following is relevant but I'm putting it out here anyway just in case it is: The battery is only a year old(and since all my lights came on, I don't think it's dead)I had an oil change on Saturday. The belts were replaced a few months ago. My check engine light is on because of an O2 sensor.
I have a 2004 Hyundai Accent, has 167k miles on it. Transmission has 80k, put in at about 155k. Came home from Tahoe, and the next day, I tried to go to work, and the gear shift was stuck in first. Hadn't had the money to get anything fixed, but when I finally got it looked at, was told I needed a new clutch and possibly a new flywheel. Been cleaning it out to sell, and today I started it up and realized that the stick is in neutral and moves back and forth freely, but the transmission is in gear. I know that, because I had to keep my foot on the clutch to keep it running. What would cause that? I'm hoping it's something easy and cheaper to fix, because I love this car and am not ready to part with it just yet. The clutch doesn't have that many miles on it either, maybe 10-15k, if that. I've had the car for almost ten years, so it's not poor driving, on my part.
View 6 RepliesThe strangest thing happened to me on the way home yesterday from work. I was driving about 110 all the way home on a highway and took an exit to my local area when i noticed as i approached the ramp i wasn't able to shift into any gears. It just felt like there was something blocking me, like a wall of rubber or something. I stopped the car on the side of the road, unsure what was going on. While the car was on and my foot on the clutch, i am able to move into all gears perfectly fine but its when i start moving i cannot go into the others. Strange. I was able to force it into second gear from first but it sounded like two plates or discs sort of sliding around on each other..maybe that was my imagination but i stopped and didn't proceed further.
While i was sitting waiting for the tow truck, i remember that the last few months it has been getting harder and harder to get into gears while driving. I would be driving and would have some resistance to get into the pocket. This progressively got worse and i guess lead to this point where i am unable to get anywhere.
First thing i thought was the transmission, but i am able to go forward in first and reverse okay and the clutch pedal was not to the floor. The clutch was recently changed, approx 20k ago.
Could it be something easy to fix? Perhaps the clutch cable has stretched out and it is not pulling me far enough into the gears making it impossible to shift. Maybe the master or slave clutch cylinder have failed? I am not sure at all!
Everything was working perfectly. I stopped at McDonalds to get a bite to eat. When I left McDonalds, the car would not shift out of first gear. I have checked the transmission fluid and it appears to be good. I shifted from Park to low, and low back to park several times making sure there was no problem there. I noticed it also kicks hard when going into reverse, and it kicks hard when going into drive. When it is driven it will not shift out of first gear.
View 8 RepliesMy daughters 2005 Hyundai Elantra has 77,000 miles om it. Just changed the wires and plugs, new brakes. Now, it runs very rough when stopped at a light and it is in gear. Now, when she has the AC running, and she stops at a stoplight, she has to put it in neutral or the engine will almost but not quite kill.
View 2 RepliesJust had all the engine mounts replaced in our 2004 Hyundai Elantra with 115,000 miles. Something new has emerged: When stopped with the engine running, there is a loud vibration in Drive, Reverse and Park, but not in Neutral. What do you think is up with this?
View 2 RepliesI'm wondering if it is OK to shift into neutral while coasting (engine on). I've read varying arguments back and forth on whether or not it hurts it. I've done for a while in my 99 suburban and the transmission still shifts just fine. I've tried it once in the elantra just to see how it affects my fuel economy, and it boosts it about 100mpg (coming off a freeway ramp). Braking and steering controls don't seem to be affected by the lower vacuum.
I can see why its not advised while the engine is off (i.e., towing), but if the engine is on, torque converter turning, transmission fluid pumping, I can't see where it would hurt.
1993 Geo Prizm with some odd 275,000 miles on it. Was at a stop sign, in first gear, and gave the car some gas. Very quickly it jumped out of first gear and stopped moving abruptly. Tried to get it back in first gear and it just stayed in neutral. Had to push it to the side of the road. Tried putting it in any gear and it wouldn't go. Then tried to have the car running in neutral and let up on the clutch and as soon as I started letting up on the clutch, something (like metal) started grinding. Pushing the clutch it (in neutral) stops the grinding. So, do I need a new clutch? New transmission?
View 11 RepliesI read a couple posts on Gear Shift switching back to neutral. Here is my situation. Got in the car to return some movies and realized I left them on the table. Went back to the house, and right before I turned into the driveway, noticed a metal coffee cup had come out of the holder and the edge was up under the accelerator. I had been applying my brakes to slow for the turn into the driveway, then when I went to accelerate, nothing, then noticed the cup.
Removed the cup and stepped on the gas to go into the driveway. Nothing. Turned the car off, then back on and tried to put into drive, goes a tiny bit then slips back into neutral. Tried it in reverse, same thing, pops back into neutral.
I can hold the shift lever in position and the car moves. It's in the driveway now and will get towed to the Toyota dealer tomorrow. Obviously a problem with the shifter as a result of the "coffee cup" under the edge of the accelerator. And yes, I know it's dangerous, hubby used the car last on his visit home this weekend and apparently the coffee cup either got put down on the floorboard or was knocked out. I bring it in the home when I'm done.....anyway.
So, the most likely cause was the spring talked about in other posts breaking, or a switch sticking or what. Seems like something got knocked or shifted out of adjustment. Does the accelerator have some type of cut off switch if something gets lodged under it?
The car is an '05 elantra, 97,000 miles, auto., car is new to me. First time on the freeway today, 30 miles @75-85 mph, at the end of the off ramp I could feel it surging, shift to neutral rpm's went to 1500, hoss the gas and back to normal. On the return trip off ramp, went to neutral, jab the gas, everything OK. I'm going to clean the throttle blade, check things, etc.
View 3 RepliesWhen temperature surpasses 90 degrees inside car (especially while sitting parked while I'm at work) I have problems getting shifter to stay in gear. When I shift in D or R the shifter immediately shifts back to neutral. I found I can hold the shifter in the desired direction and the car goes like normal.
I tried a test of leaving windows slightly open and found the car cooler inside and the gear shift problems did not occur.
The dealership says the gear shift is electronic, no gears. Is there a switch for this under the panel by the gear shift? I have a 2008 Prius, that I recently purchased used. My wife has a 2005 Prius that we purchased new and have never had an issue like this.
My 93 Honda Civic (manual T) is starting to be difficult to shift into gear. I mainly notice it when the car is idle and in neutral. I go to put into 1st or reverse and it won't go. I try all gears at that point, and it's the same. When it finally does go, it's a loud thud-like noise. People around look over at me! It doesn't happen every time, but I am noticing it more and more. And it's a bit scary when I have been at an intersection or something and I can't get moving. It has 189k. I have also noticed that the car is loud, too, when I am in reverse up our driveway and the clutch is slightly depressed.
View 7 RepliesThis morning my 2011 Camry LE won't start. Based on looking at car manual I think the 'Engine Immobilizer System' is still engaged and perhaps not recognizing my key, neither of them since I tried the spare as well. The instrument panel stays black and I can not turn the key or even move the gear shift into Neutral.
Any way to fix this without calling for a tow? So.... found out the problem! The steering wheel was angled slightly. With key in the ignition we jerked the steering wheel slightly and it released the ignition and was able to start.
4R70W. This one is in my 99 F-150 with the 4.6. From what the previous owner told me this trans only has 13k miles on the rebuild and I believe him because the converter is bright blue and when it does shift right, the shifts are solid and fluid is very clean. Truck only has 98k miles on the body as well, so it's possible the truck did sit a while because my tires have a ton of tread on them, but they are dry rotted a bit (dated 2006 IIRC).
Issue: When the trans is cold (sat overnight) it will shift to neutral between the 2-3 shift for 1-3 seconds depending on outside temperature and then drop into gear. But it only does this for the first 30 seconds or so of driving, after that it shifts normal (although it does seem to hold gears a little longer than I would think it should on occasion and not upshift). I have only gotten it to do it once per cold start so it seems like once the trans gets any heat it's fine.
I was also thinking I was getting drain back and maybe it wasn't heat related so I dropped the pan, replaced the filter, fluid and pan seal (it had a small leak) and torqued the valve body. Two of the bolts were a little loose, but the rest were fine. Tightened them to spec and put it back together with no dice. Truck also gets pretty bad fuel mileage so I'm starting to think maybe there is some temp sensor screwing everything up?
I own an automatic transmission 2004 Hyundai Accent with about 180,000 miles. I bought it brand new, but it seems to be having trouble shifting into the right gear. Many transmission "specialists" keep telling me they can't figure out what is wrong, aside from offering to completely rebuild my transmission. The car has the following symptoms:
1. At a stop sign or red light, my car doesn't always begin idling properly. Sometimes it just won't go anywhere at all, even with the motor running.
2. As I drive down the highway, it acts like it jumps into a higher gear for no reason. It sometimes resets itself with no action on my part.
3. The car jerks back and forth, not seemingly due to shifting into gear, but randomly.
4. The check engine light does not come on often, but by the time I can use a DTC reader, the light goes off.
Everything seems to be intermittent, so I can't replicate the problem on-demand for anyone who wants to inspect the problems. Is there anything I can do? Is there an easy way to figure out what's really going on? I'm assuming this is transmission-related...
My check engine light has recently turned on in my 2004 hyundai elantra, and since it has come on my car will kick and sound like its going to stall, works but the automatic transmission refuses to shift. This inconsistent because it sometimes works fine with the light on and sometimes the light won't even turn on and everything is ok. What's wrong?
View 3 RepliesVolvo Automatic 1992 240 - So, just started to back out of the garage and, all of a sudden, my gear shift got stuck in neutral and then started shifting without engaging the transmission at all. Pushed it back into the space and, taking a look underneath, I realize the control rod's completely detached from the lever in the transmission.
I can re-attach it, but it just comes loose again when I shift. It seems like something should be in there to hold the control rod in place with the transmission lever, but I don't know what because I can't seem to find any documentation on what everything should look like down there.
Attaching a couple shots, one with a circle around the area that's coming un-attached since the angle's a bit off.
Attached File(s)
IMG_8972.jpg ( 1.09MB )
IMG_8978.jpg ( 938.64K )
I have a 2006 hyundai sonata, which has possibly the worst designed cup holder of all time. Because of this awful design flaw, I stopped my car at a light yesterday and some of my coffee spilled into the gear shift box. Now when I am in regular D, it appears the car stays in 1st gear. This sonata also has the option of pushing the stick to the right so you can manually shift gears.. I think it's called sports mode or something. When I try that, I can shift it up to 2nd, but I drops right back down to 1. I left it overnight, hoping it was just some wet electronics and would dry, but this morning the problem persists. Not sure if there's a fix for this, if I should take it to a transmission place, or just my regular mechanic. Someone suggested contact cleaner, which I might have I just have to look.
View 10 RepliesI have an 07 Hyundai Accent. Occasionally when I start it, it will bang into gear and will not shift into high gear. It is an automatic transmission. If I turn it off and restart a couple of times the problem will disappear. I occasionally get the check engine light with this problem but it goes out the same day. It has also occasionally been going down the highway and will shift out of OD and increase rpms. I can pull over and restart and the problem goes away.
View 4 RepliesFor the past 3 months, upon shifting from 2nd to 3rd gear, the car lurches forward in a hard shift. Sometimes, it is nothing more than a benign "clunk", and other times it is violent, as if hitting a wall. This does not happen every time it shifts and even under identical acceleration, the results vary from none to violent. The number of violent shifts vs. small jolts has increased over time, and all other transmission functions and shifts are fine/normal. After much time researching the inter-blogs, I have come to no consensus on what is causing this or how to fix it.
Some say it is the adaptive shifting program and it just needs updating and others say it's the tranny and a rebuilt tranny replacement is the only thing that eventually fixed this problem (though one posting on the Hyundai forum is of the same exact problem, but the solution is worrisome -- contact negative battery terminal to positive, let sit for 10 min, reconnect, then drive at 1/3 throttle, shifting through all gears a dozen times. Poster says this resets adaptive shifting program and worked for him).
Finally, today, I took it in for a diagnostic with a local transmission specialist, and they could only replicate the hard shift once, but when that happened, he said the car went into limp mode and read two codes: P1193 and P2127. The car has never gone into limp mode (P1193) nor shown an signs of suppressed RPMs associated with this mode. Also, he seemed to focus his attention on the low voltage to the pedal position sensor (P2127) as being the major issue that is causing the hard shift. I also called a past dealer that worked on a similar issue with the car when I bought it used 4 years ago and they recommended updating the adaptive shifting program as they did last time; though I don't recall if the shifting issue was the exact same problem I am having now. So, a few things:
Does this sound like a computer issue or a tranny issue? Could the pedal position sensor having low voltage cause a shifting problem like this? Any merit to the connecting the battery terminals idea? Should I be wary of the mechanic that did the diagnostic today?