Honda - Cr-v :: Rough Vibration / Shuddering / Chattering When RPMs Between 1000 - 2000
Mar 23, 2015
I leased a 2015 Honda CR-V AWD LX on March 11, 2015. The following day I noticed a rough vibration/shuddering/chattering that appeared to be coming from the transmission when the rpms ranged between 1,000 and 2,000. The roughness was evident at any speed (mpgs) when the tachometer reading was between the previously stated range. The service technician reported feeling the same roughness, but noted that the problem was characteristic of the CRV with a CVT transmission. On Tuesday March 17, I went back to the dealer and discussed the problem with the service manager. He also stated that he was aware of that particular problem and that it was peculiar to the 2015 CRV with the CVT transmission. He took my car for a test drive and admitted feeling the chattering. It was also evident to me as I sat in the passenger’s seat. He then took out another new CRV and it too exhibited the same characteristics.
View 18 Replies
Advertisement
Reconditioned engine 5,000 miles ago. Last maintenance check at dealer found nothing wrong. 2000 Honda CRV.
View 4 Replies
I have a 2000 b5 wagon with a 2.8 5spd with 200k on it .... Its slammed on coils and i get this squealing in reverse i dont know what it is i just rebuilt the front end ie control arms... also have a nasty vibration from 1000rpms to 3000 rpms could that be engine mounts/snub mount?
View 7 Replies
I drive a 2008 Elantra automatic,and have a constant engine shudder/vibration whenever the rpms are between 1000 and1500. The engine shudder stops as soon as I accelerate above 1500 rpms,or take my foot off the gas completely.
The dealer recommended cleaning of the fuel injector system,not sure if thats the course to take.I do know my model has had fuel pump issues,but the dealer has told me all recalls on the car have been processed.
View 3 Replies
2007 Camry LE. This morning while driving, she noticed a shuddering that scared her. She called me and parked the car as soon as she could. I went to drive it around and, as she had said, it was shuddering.
I drove it for a bit, neighborhood and highways, and took note of everything. The RPMs were low - About 500. I'm not sure where it usually idles, I rarely drive this car, but my Jetta idles around 900 so this seems strange to me. RPM gauge occasionally bounces around at idle. Once the car gets moving there are no issues. Only at complete stop. It feels like the car is about to stall.
I drive a manual and if I keep it in gear while approaching a stop it makes the same shuddering because the RPMs are too low for the selected gear. This is what it reminds me of.
Here is a video of what's going on under the hood. As you can see, the airbox is vibrating heavily. That's the most obvious place. The engine and intake manifold are also bouncing around, but it's hard to see in the iPhone video.
Video ... ... ...
View 10 Replies
I have a 2008 Ford Focus - 4 Door Sedan SE 60300 miles.
I've gone to 3 mechanics now and no one can seem to figure out whats wrong with my car. Here's whats happening:
About 1 1/2 years ago I took my car to get an oil change at Jiffy Lube (Yeah never again). When I left, my car was idling funny... Silly me didn't take it right back and have them tell me what was wrong.. so I let it go, well about a month later it started idling even weirder. Basically it feels like my car is shaking when it gets under 1000 RPM and I notice my RPM dial start falling and bouncing back, acting like its going to stall, but never does. I notice a loss of power when this is happening (on speed up and just accelerating in general). All of this is random, I can't seem to put a pattern to it as to when it happens. One day I'll start it up and everything is perfect... Then I'll shut it off and restart it later, and it starts vibrating and puttering again... No signals as to if its hot/cold or wet/dry, no environmental variables seem to cause it to happen anymore than others. And there is no check engine light on, everything "looks" normal.
What I've had done to it so far is:
Air filter changed / reseated
3 oil changes (keep getting told it will work)
Throttle cleaned
Computer reset for idle sensor data rebuilding
Now I'm told that I need new engine mounts, and that could be the reason for the vibration. I'm thinking that the vibration caused the mounts to wear out, more so than the mounts being the cause. Mainly because I don't see how bad mounts could cause loss in power/bad idling.
What could be wrong?!? Really bugging me and don't want to keep throwing money at it for phantom solutions. Seems like mechanics I go to can't figure it out unless there is a check engine light on with some diagnosis code to tell them exactly whats wrong.
View 8 Replies
My car is a 2001 honda accord v6. It sat for 3 winter months. When I go to turn it on in the morning, the car will rev while idling. Jumping between 1000 and 3000 rpms. Why this might be happening?
View 3 Replies
I have a 2005 Chrysler 300C ( original owner )Mileage 172,000 and I take care of my car. I use full synthetic oil and change it every 5000 miles. I noticed a hesitation between 1000 and 2000 RPM's. It disappears after 2000 RPM's. The Chrysler dealer kept doing repairs and claimed the problem was gone and it is still there. The dealer did a full tune up, induction service and also replaced the EGR valve, gasket and seal. The problem gets worse in higher mountain altitudes.
View 3 Replies
So lately my 2000 Jetta GLS hasn't been running that smooth I can tell when I'm changing gearing and when I start the car and the car idles around 1000 RPMs. I think it may be the engine miss firing because some times I can feel the car shaking but I have no check engine light. Lucky... Also the coolant is leaking idk what the exact problem is but everywhere I go there is a puddle of coolant under my car.
View 2 Replies
My V8 is "sputtering" between 1000 - 2000 RPMs. Not only can you feel it, but you can see the tachometer bounce up and down as well. No problems accelerating or putting the engine under load - it's only between that RPM range where there seems to be hesitation. The car is not giving any fault codes, and I just recently had all plugs and coils changed. (The car ran great for 2000 miles following the plug and coil change.) It started on a road trip, and I took it to the local dealer. They thought it was bad gas. (I've since run several tank fulls through it...)
My suspicion is a mass air flow meter beginning to go, but until it triggers a fault, I can't say for sure. The dealer wants to check the MAFs values and to do a fuel tank pressure test to see if it's the fuel pump. I do have the Real Driver warranty, but they will not cover investigative costs. I'm not too excited about throwing money to test a bunch of different things.
View 12 Replies
2010 F150 ... So I have the tick noise at rpm's 800-1000 at drive through, stops, etc. So I did research on it a few months ago and saw that it might be VCT's but should be able to drive. so I drove it waiting to save money and have it go to a shop. well this past weekend while coming home from work my oil light came on the pressure dropped to zero, I was on the highway so I drove about another mile to get off highway and once I got off my truck died. I had it towed to my house and I thought I blew my motor. So I started doing research here and found that the VCT's AND cam Phaser could be bad. so I replaced my VCT on driver side put it all back together it started and loud knock was gone. then after 5 mins it was back very loud knock!
So I shut it down and took apart the passenger side once I got the valve cover off I found the problem.... The bolt that holds the cam phaser in place snapped off and was riding along the camshaft. So I took that out and extracted remaining part of bolt. inspected my camshaft and it was really messed up. so I bought new Phaser and Camshaft. the camshaft just came in today and I am trying to put it back in. but the hole for the pin in the phaser doesn't line up and I cant spin the shaft to make it line up. should I spin the cam phaser? I marked the chain and the phaser is where it should be on chain, but with that bolt snapping off could that have thrown the timing off so my mark is no good? when I lay the camshaft in place it sits perfect and if I just move the phase over 2-3 links it will all fit together. Should I do that?
View 5 Replies
I recently got the EGR system in my 1998 Rav4 working (replaced VSV) after driving with it non-functioning for several years. Without the system functioning, the engine ran great, but fuel efficiency suffered. Now, when the engine is warm only, the engine knocks and lugs between 1000 and 2000RPMs. This usually occurs right when I shift into 2nd gear. There are no engine trouble codes.
View 8 Replies
W12 2004 light vibration/struggling during light.
View 3 Replies
But I have noticed over the past week of driving, whenever the RPMs are around 1000-2000, it is very hard for me to pick up speed, and I can feel a little bit of a rumble/vibration through the steering wheel. So...
If I feather the gas, the RPM increases slightly and you can hear/feel the engine rumble/vibrate. The speed doesn't really increase...
If I hit the gas more than 1/2 way down, turbo kicks in and the car shoots forward.
Is this normal? I find it very hard to add a little bit of acceleration if I feather it, the engine seems to be resisting it, if I hit it any harder, the turbo kicks in around 2500 RPMs. It almost feels as if it is in too high of a gear and the engine has a hard time accelerating a little bit...This is around ~40-60KM/hr
View 4 Replies
I have a recently purchased 2000 ford ranger 4X4 with approx. 130,000 miles on a 3.0L. When I bought the truck, it was running rough while in gear at idle, after first putting it in gear, and when coming to stops, then it quit running all together. I started by replacing plugs, wires, and ignition module. I finally got it to fire up after that, but instantly noticed the tell tale white smoke from the exhaust. Needless to say, my oil looked like chocolate milk. Rather than having the heads machined and checked, I opted to purchase a new set of cylinder heads from Dover cylinder head.
I got those on this week and she fired right up. After a few oil changes to eliminate the residual coolant from the oil passages, she still starts and runs fine, although the idle is a bit rough while in park. When I place it in gear the idle gets a little rougher. After a quick trip down the road, I'm noticing a pretty solid shudder when coming to a stop, almost like it's stuck in 2nd gear, but I can't really tell for sure. Seems to shift fine going up through the gears, but coming down is when the issue is.
I believe I'm dealing with two separate issues, one being the rough idle upon startup that doesn't seem to go away, and two being the rougher idle upon stopping. I've read everything from EGR valve, idle air control valve, low fuel pressure, and a laundry list of other things, and I just don't want to start throwing money away chasing my tail.
View 4 Replies
I've made posts about a rough idle before now I noticed something new about it. I noticed when I approach a red light the vibrations don't start immediately. They start as soon as the RPMS would drop a little. They stay above 500 but it seems like it's below 750. As if the engine is slightly starved from power? Now i'm wondering if it could be related to another problem I have.
Whenever I start the car, the battery light flickers until the car is started all the way. This is on a 2007 Camry 4 cylinder. So far everything iv'e done is: New NGK Spark Plugs, NEW OEM mounts (all 4) Seafoamed the engine, Seafoamed the throttle body, cleaned the MAF sensor, New air filter, and cleaned the air filter box, replaced the PCV Vlave, new belt, new alternator (duralast), and a new battery (from autozone).
View 2 Replies
I have a 2003 Toyota Camry XLE that has had the following issues.
1) When going over speed bumps you can hear a very loud creaking in the front and rear and occasionally a clunk in the rear.
2) When driving on rough or bumpy roads you can hear a metallic chattering coming from the driver's side.
3) There is a vibration in the car that I can't pinpoint but I was told the front rotors are slightly warped and that could be causing it, thoughts?
4) I put brand new tires on in January and it has less than 10,000 miles on them but they already look like they need to be replaced. They are Michelin Hydro-edge tires. I have had it balanced/rotated at 6,000 miles as well as an alignment. Nothing was said to me about any problems by the tire place when I had it done a few months back, which I find odd.
5) When turning into parking spots or turning at low-speed in general, especially when turning right, I sometimes hear the tires squealing.
I was going to go ahead and replace all 4 struts, strut mounts, strut boots, rear sway bars, all 4 rotors and brake pads. But I wanted to make sure that this would fix the problem.
Do I need to get the front Driver/Passenger CV Half Shaft Drive Axle assemblies? Are there any other parts that need to be replaced that could fix the issue? (Tie Rods? Ball Joints? etc?) Are there any other parts you'd recommend replacing while working on the car? I tried searching but could not find anything that specifically matched the problems.
View 6 Replies
1995 Honda EX with 150,000 miles. Its been running rough ie rough idle, stalling at low rpms etc Additionally for awhile now when humidy reached north of 85% the car wont start. It cranks but rarely runs.
Took it to a mechanic last week for a tuneup. They replaced the Distributor cap, spark plug and wires and fuel filter. Car ran great for a day. Then progressively got worse. Was undriveable the other day stalling misfiring while at speed. Took it back today. They determined that it was still not getting spark and replaced the distributor. They did so, test drove it, declared it good and I came to pick it up. Paid the bill, walked out to the car and the damn thing would not start. Humidity was high.
Mechanic pulled a spark plug and put a tester in and didn't get a spark when cranking. He is assuming the distributor he just put in is bad. So they are keeping the car overnight to be fixed in the morning with a new distributor.
However I'm not convinced the dizzy is bad, I believe, as I've read that the Honda's ECU is probably bad and shorting out in the high humidity. Can a bad ECU would prevent spark?
View 2 Replies
RPM's will not get above 2000, in 1st and 2nd gear. No power....
View 16 Replies
I have a 2006 Honda Odyssey with 40K miles. The valves have been making a chattering noise for awhile now. I have tried different brands of gas (highest grade) - no luck. I took the car in to the dealer while it was still under warranty they could not find anything wrong. I took it again lately and they said not to worry. It seems like some sensor is not functioning properly but I could be wrong.
View 18 Replies
I have a 2000 Celica GTS that idles a little rough it has 118000 miles on it.. Fluctuates between 500 rpm and about 1100 rpm. Doesnt always do this, usually after ive been driving for a while. I also may have a rod knock, what parts would i need to fix both of these issues? Me and some friends can do the work ourselves, i just need the parts.
View 1 Replies
