Honda - Cr-v :: 2005 - Fuel Air Sensor Replaced But Still Getting Codes P0133
Apr 18, 2011
I checked my engine codes after the engine light came on. They were P0133 and another indicating an A/F upstream sensor problem. I had it replaced by an independent mechanic. A few days after I had the same code. Mechanic went over it and thought it was loose wiring. A few days after codes P0133 and P0128 were generated. Now the light will come on every few days, will stay off for a few. Do I have to get my computer upgraded? Honda 05 CRV ...
View 2 Replies
Advertisement
Keep getting o2 fault codes. Replaced sensors came back. tried another set of sensors came back. Checked wiring for breaks no luck. Replaced ecu still no luck. So going through wiring again and checking for continuity. Looking for a list of what pins to check for voltages, and what each should be from ecu to sensor connectors. Looking for what wire is signal and how to and what voltages to check for...
View 5 Replies
I have a 01 elantra. Check engine light is on. Diags say p0133 o2 sensor slow bank 1 #1. Any way I have replaced the front sensor. Actually now I have 3 of them. The exhaust does not leak. New gaskets on the converter. New flex pipe and everything has been welded.
View 7 Replies
I have a 1999 explorer with a 4.0 ohv auto with about 174,000 miles on it. the PO changed the coil pack, wires, plugs, MAF and cat on it trying to get rid of codes. I know the from searching that they are both precat 02 codes. So I am planning on looking for vacuum leaks with propane around intake and egr and checking on the fuel pressure and wiring and connections. Is there any thing else I should check out? for both sensors to throw this code? The truck runs ok just has a shutter when going up hills and stuff.
View 4 Replies
I own a 1998 Mitsubishi Mirage with about 190,000 miles on it. The engine light has started coming on and I get three codes:
P0170 Fuel Trim Bank 1P0136 Oxygen Sensor Bank 1 Sensor 2P0301 Cylinder 1 misfire
Read more: [URL] ....
View 1 Replies
Truck Specs: 1997 F250 LD 184000 miles and a 5.4, automatic, shift on the fly 4x4 extended cab.
What I did: Changed the exhaust manifold gasket on the right side. There were some broken studs which came out with a stud remover.. No torch was used during this evolution.
What happened: After driving 10-15 miles it set the codes that I listed in the subject line. Reset the codes 20 or so miles later the P1131 code set again. (both times there was a noticeable loss of engine power) The upper O2 sensor checked out with a meter. When I checked the voltage on the truck's harness plug referenced to the NEG terminal on the battery, both the power and gnd had 12V- Key On Engine Not Running (KOENR).
What I did: Cleaned the connections put dielectric grease in the connections and reassembled. Reset codes; all was well ~ 100 Miles later the codes are back. I also ran a continuity check from the plug to the control module, they check out fine.
View 1 Replies
2004 Honda Civic with 166000 miles.
--Had Check Engine light on for a couple days and code reader said P0135. Parts guy said this means "Bank 1", my Haynes book calls this code for " Primary Sensor 1" Is this the same as "Upstream"?
--Replaced O2 sensor (Denso 192400-1160 05F12) myself with a new one (Bosch 15710). Fit perfectly, plugged right in.
--Check engine light goes off for about 5 minutes but comes back on with code P0134.
What should I do now? I replaced the sensor closer to the engine before the catalytic converter. Very easy to reach from the top. I rented the correct tools and did not damage or force anything. Is there a second O2 sensor after the cat that is not so easy to reach? Was that the one I needed to replace? Did I misunderstand the meaning of "upstream" or "Bank 1"?
View 12 Replies
I replaced the fuel pressure sensor in my freestar...I drove it around for a minute then noticed a strong smell of gas. I stopped and then put the old sensor back in and now it won't start.
View 6 Replies
Got a 1996 Volkswagen Cabrio with around 125k miles. Recently the check engine light came on. Had the code pulled (P0133 02 Sensor Circuit Slow Response) and reset but it came back on shortly thereafter. I've also noticed that the car idles strangely, generally after it has warmed up a little bit. Basically it will idle rough and sound as though it might choke out but if you give it a little gas it goes back to a normal, even idle.
Right now it's getting around 20+ MPG average which seems a little low but I only purchased it 3 months ago so I don't have much to compare it against. One other thing I've noticed is that the plastic molding around where the gas nozzle goes in is cracked which makes it difficult to fill it up since it doesn't make a good seal unless you position the gas nozzle just right.
Any thoughts on whether either of these problems might be related to the weird idle? How hard is it to change the front 02 sensor?
View 1 Replies
I just posted last week that my check engine light was on and the dealer wanted to replace fuel injectors. But after the fuel throttle was cleaned and oxygen sensor was replaced the check engine light went off. However, yesterday the check engine light came back on. I am talking it back to the dealer, in a couple of days. Where can I go to get to get the error codes read so I have them before I go back to the dealer? Around 128,000 runs fine, around 40 miles per gallon. Last time I had the oil change dealer nothing came up on the 30 point inspection.
View 7 Replies
1995 Ford Explorer, 4 ltr. engine, pushrod. Will not start. Replaced fuel pump, fuel filter, every relay, pressure regulator, and the crank position sensor. I realize there's a whole bunch more parts under the hood, but I am ready to give up. Before the fuel pump would not run. Reason for replacing the parts. Now it won't stop running and you can feel the fuel by-passing at the pressure regulator. When checking the pressure at the rail I get zero !! I used a tire pressure tester for this. And, like I said no pressure. This vehicle has around 170,000 miles on it.
View 8 Replies
I replaced the pads and rotors on my 05 Civic 3000 miles ago. Now it is pulsing badly again when stepping on the brakes. I can feel the pulse in the brake pedal and the steering wheel. What should I be looking for when I pull off the wheels again.
View 8 Replies
I have a 2005 honda civic. About a month ago it started overheating. Drives Ok on the highway but heats up to the H mark almost as soon as I get off the highway. Have replaced the water pump, thermostat, radiator, flushed the system, most hoses, fan, 2 sensors, timing belt, spark plugs and had the head gasket checked 3 times by 2 different shops. Both said it was fine. The mechanic that has done most of the work is baffled. Says he has never seen anything like this and is at a loss as to what to do next. I am supposed to drive this car halfway across the country in a week to meet my husband who is in the air force. Should I just sell this piece of junk!?
View 10 Replies
I have a very well maintained 2005 honda odyssey with 150,000 miles on it. It typically gets 22 m.p.g. It started using an unusual amount of gas - was getting 12 m.p.g. Took it to the mechanic and turned out the gas pump was cracked. We replaced the gas pump and the gas line, and it was getting 14 m.p.g. Took it to another mechanic, and he said that the spark plugs were the problem as they were not official Honda spark plugs (we replaced them at around 110,000 miles). So we installed the official Honda spark plugs, but still no good. I have visited several mechanics and no one seems to know.
View 7 Replies
You know the "mechanic's fiances truck" problem. I recently replaced the cam sensor in my 05' F250 Gas. The check engine light had been on for a while before that and my truck rode great, however I now want to sell it and I can't do that with a check engine light on. It's got about 85k miles on it.
After replacing the sensor, the light went off for about 20 miles, but it is now back on and my truck seems to miss every once in a while on acceleration or cruising. Some days it's worse than others. The check engine light still says cam sensor, but the sensor is brand new.
My fiance is a mechanic, so I don't know all the details about code numbers and such. However, I want to sell this truck pretty soon, and I would like it to run correctly. His dad (another mechanic) seems to think it could be a coil and wants to wait for that light to come on, but I would rather fix the problem and sell the truck!
View 1 Replies
I have an 05 f350 6.0 that I recently bought. It was fine until a few weeks ago when it died while I was driving down the road. I pulled to the side and it started right back up like nothing happened and kept driving like normal. Skip to last weekend it did it to me twice but the second time it would not start so I plugged my programmer in and it showed p0336 crank position sensor and cam portion sensor codes (I can't remember the number of the second code) I have read a few posts that said maybe it's the icp sensor so I went ahead and replaced that with no luck. The batteries went dead from excessive cranking which I know isn't very good for my starter but I was getting a little upset.
View 11 Replies
I have a 2005 honda odyssey van and the oxygen sensor light keeps coming on.
View 5 Replies
I know the code is fuel level sensor, but i can't find the parts online. nothing comes up with the part name fuel level sensor. What is the part number for this or the number for kit because i believe there are 2 sensors?
View 1 Replies
Yesterday, I turned on my car and got a message on my dash telling me to check my fuel cap. I did, and it was fine. The message still didn't go away, so when I got to work, I actually unscrewed my cap to check and make sure everything looked normal. At this point, I noticed that the metal flap that usually covers the opening of the gas tank was gone. After showing this to my neighbor, he said that it looks like there's actually an entire component missing from the mouth of the tank, and not just the flap.
I'm guessing that, the last time I got gas, this part of my gas tank went with the nozzle when I took it out. How I didn't notice this is beyond me. Unfortunately, the last time I got gas, I was 100 miles away from home.
My question is, am I in for a nauseatingly expensive repair here? Is it possible to just replace that one part, or am I going to end up replacing a whole lot more? I haven't taken it to a mechanic yet because I'm trying to go in armed with some knowledge about what can be done here.
View 4 Replies
I have honda civic 2005 with 170,000 miles on. My car has been little shaky with cold start in the morning and Engine light finally on. I was told that I need new fuel injectors from local mechanics. I'm a poor student so I decided to fix it myself. I was able to reach down to fuel rail and It was very challenging to take the rail & injectors out. After I finally pop them out with long driver/hammer, It is even harder to put new ones inside, all the way in. I tried put some oil at the end but still did not completely go in. Is there any special tool I need to use to put them in? I tried oils...ect.
View 9 Replies
So i just finished putting in new high pressure oil rail cup seals in and a new #2 injector. Truck was running great for about 5 miles and then just shut off. When I had it towed home I plugged in the super chips tuner "no tunes installed" and I have a p0460, p0463, p2290, p2291. I also have a #7 glow plug circuit failure Ive been a little neglectful in getting done.
View 6 Replies
