Honda - Cr-v :: 2001 - Check Engine Came On / Cylinder Misfire Code


Jan 21, 2013

I have a 2001 Honda CRV with about 140,000 miles. It is an upstate NY car, so has seen its share of salt and rough winter driving, has a little bit of rust.

I recently brought it in for repairs because it was overheating. It was over the holiday weekend and I had a job interview to get to so I brought it a chain, which was the only open mechanic I could find. They told me there was a coolant leak and replaced the radiator.

The next day, the check engine came on. Cylinder misfire code. I took it back to them and they wouldn't give me a straight answer on what was going on but insist they told me that would happen and it needed more repairs which I had apparently refused. They told me it's probably the spark plugs/wires are old but maybe there's more damage, but basically that they didn't want to deal with it.

So I brought the car to my regular guy. He says, yeah it needs a tune-up. So he replaces the spark plugs and wires etc and gives it back. I drove it for a day and the light came back on. So I brought it back to him again and he refused to do anything. Wouldn't give me some possible causes or explanations, just says come pick it up. Didn't say stop driving it, take it to a dealer, he just reset the check engine light and said its probably fine.

The next time I drove the car, while it was warming up the check engine light was flashing. By the time the engine was warm the light had stopped flashing and was on.

View 4 Replies

Advertisement

Honda - Odyssey :: Cylinder 4 Misfire - Check Engine Light

Honda Odyssey 2005 – 176000 miles. Cylinder 4th Misfire – check engine lightHonda has about 176000 miles. When cold – before warming up – it acts like nothing is wrong – as it gets warmer – to the middle of the temperature gauge – it misfires.And runs rough. Evaluation: Honda Dealership thinks it is a cracked Valve or needs adjustment – they have replaced a spark plug and swapped coils. Not for sure.They think if that is not the case then there could be additional problems.Question: Why does it act normal when cold ? How can we confirm if it is the valve and not cracked head?

View 15 Replies

Toyota - Prius :: Check Engine Light Came On - Code PO301 / Misfire On Cylinder 1

I have a 2007 Toyota Prius with just under 30,000 miles. Yes, I don't drive all that much, which makes the Prius the perfect car. I get it serviced every 6 months by the dealer. So far, other than oil changes, the only actual maintenance has been tires, a 12 volt battery, and a $300 "inspection".

A few weeks ago the "Check Engine" light came on. I pulled the code P0301, which translated to "Misfire on cylinder 1". The car was running great at that time, and since clearing the code it has continued to run without the light coming on again. Given that my maintenance is more time-related than mileage-related, it's possible that the ignition system needs attention. However I'm reluctant to bring that up at my next maintenance appointment, because the guy writing up the service order will always answer "Yes" to every "Do I need ..." question.

View 2 Replies

Prius (2004-09) :: Check Engine Light With PO301 Cylinder Misfire Code

I bought my 2008 Prius 9-14 with 29,000 miles on it. (rebuilt title-big mistake I now know). I found out after I bought it that it had sat for 5 years before it was rebuilt) I figured it was a miracle the hybrid battery even worked.

I had no problems until 2-4-15 when check engine light was flashing and the car was shaking. The local mechanic said was the “clutch” (torque converter), took the engine and transmission out of the car to fix it ($2200). But he realized the mass air flow sensor (MAP) was not working even after he put a new one in so had me take the car to the Toyota dealer. The dealer found a cut in the engine harness and advised me to replace the harness which he said would cost $2800. The local mechanic saw the cut via my cell phone photo and offered to fix it for free which he did.

The next day check engine light comes on after driven 25 miles with code PO 301. (means misfires in cylinder one). The local mechanic switches cylinder 1 with 4, same code the next day, local mechanic switches the coils to the cylinders, still the next day the same code. He switched the fuel injectors. Same problem of cylinder 1 misfire. He cleaned the oil out of the intake manifold, did fuel injection cleaning, and cleaned gunk out of the fuel line. Car would drive good about 20 miles then same check engine light, same code, sometimes code PO300 (random multiple misfires).

View 19 Replies

Nissan - Sentra :: Check Engine Light Came On With P0304 Cylinder 4 Misfire Code

(This is a continuation of a previous thread: [URL] ..... )

I have a 2005 Nissan Sentra with 75,000 miles on it. Several months ago (see above link) the check engine light came on with a P0304 cylinder 4 misfire code. The only symptom appears to be a rough idle/shaking every 3rd or 4th start for the first 10-15 seconds, but runs smoothly afterwards. My mechanic replaced all my spark plugs (I had new plugs put it at 50,000 miles for the same issue) of which the one from cylinder 4 was worn down much more than the rest. The problem persisted so they replaced my fuel pump and fuel filter and switched the spark coils from cylinder 4 to a different cylinder, but the code still read cylinder 4 so it wasn't the coil. That was back in October.

I took my car back in last week for the same problem and without starting my car (because the problem is worst on the first start) they pushed my car into the bay and did a smoke test, no leaks in the fuel lines. Then they checked the cylinder and said that there was "excess" fuel in the cylinder and replaced the fuel injector. Then after ~3 days the check engine came back on with the same P0304 misfire code. Previous repairs/diagnostics rule out spark plugs, coils, fuel pressure, and injectors.

View 19 Replies

Santa Fe (DM - 2013+) :: Check Engine Light Code P0303 - Cylinder Misfire

I own the 2014 Santa fe turbo 2.0 litre limited which has 4000 km on it. Within 210 km the engine light came on 3 times. I took it into the shop and they ran a code of P0303 which is a misfire, they changed the coils #2 and #3 and cleared the code. The second time it showed the same code but the shop said it was in the history so that is why the same code came up again. They ran an update ECM? and all was good. Now the 3rd time they tell me no code has come up and can't do anything about the engine (they cleared it) but it was like chasing ghosts. My vehicle runs great so not sure why I am constantly having this issue.

View 68 Replies

Elantra XD (2001-06) :: Check Engine Light (cylinder 3 Misfire)

As the title says I have plugged a code reader in and it says "cyclinder three misfire". So I pulled the plugs and good god they were nasty. Some having a gap of 80-90 thousandths of an inch. So I figured the plugs were the source of the problem, thus I replaced them but to my dimise the check engine light is still on, and still reading the same ol' "cyclinder three misfire". I have put 350 miles on it in 24 hours of changing it to allow for proper time of the circuit cycling for the light to change but not sure if it takes longer...?

I also went ahead and checked the plug wires resistance when I had the plugs pulled and they ranged from 1.5-2.5k ohms shortest to longest (cylinder 4-1). And if your curious the magic cylinder three was around 2k ohms for however long that wire is, my guess would be 18 inches. Would this be out of tolerance, I know the norm is 10k ohm for every 12 inches or so...?

My next guess would be replacing the power pack or I guess you car guys call it the "ignition coil"...? I will say that the car does run much smoother after replacing the plugs.

View 5 Replies

Tacoma :: 2000 V6 Check Engine Light Code P300 / P306 - Cylinder 3 And 6 Misfire

2000 Tacoma v6 has has always ran good, but has check engine light code P300 & P306. cly 3 & cly 6 missfire, lean bank 1. Vacuum test showed no problems.

I've changed plugs & wires, switched coils around cleaned mass air flow sensor, checked timing. Ran Seafoam through intake, and gas tank. Check engine light went out for about three miles, then came back on. What else can I do to keep that blinking check engine light off?

View 1 Replies

Ford - F150 :: Check Engine Light Started Flashing / Cylinder 4 Misfire Code

1997 Ford F150 - 133K Miles - 6cyl - 4.2L. This is a truck that gets less than 2K/year put on it. Has had "issues" with worn bearings and holding oil pressure for a few years now. Yesterday, the check engine light started flashing (as opposed to solidly lit) and the code came back as a cylinder #4 misfire (only the one code). The truck was clearly not firing on all cylinders and at idle, ran terribly (couldn't be driven). I just did a compression test on all the cylinders and all measured around 140-145psi except the #4 which read almost 170psi. I rechecked this a few times as well as a couple of the others and am now sure of the results. What could cause this one cylinder to have a higher compression ? Is whatever is causing this increase in the compression, also be the cause of them misfire ?? I'm stumped here and quite frankly, expected the compression on the #4 cylinder to be really low as opposed to the others.

View 13 Replies

Ford Ranger / B-Series :: 1996 4.0L - Misfire On Cylinder 3 / Check Engine Code P0303

Got a 1996 Ford Ranger with the 4.0L in it that has a misfire on the #3 cylinder and giving check engine code: P303. Have tried new plugs, wires, distributor, switching out the coil pack with a known good, checked injectors for pulse, checked injectors, moved injectors and still the misfire remains on #3. Removed the valve covers and all appears to be well.

View 14 Replies

Mercury - Grandmarquis :: 2001 - Check Engine Light Came On / Misfire On Cylinder 4

I have a 2001 Mercury Grand Marquis. The check engine light came on and AutoZone diagnosed it as a misfire on Cyl. #4. I changed all the plugs but I do not know how to turn off the light to see if I fixed the problem. How to turn the light off.

View 3 Replies

Ford - Ranger :: 1997 - Check Engine Light On With P302 Computer Code / Misfire On Cylinder 2

1997 Ford Ranger with 190K miles has check engine light on with P302 computer code, meaning misfire on cylinder 2. Engine runs rough at idle only once it warms up, which only takes a minute. It is usually fine while driving, but it's a lot easier to feel a misfire at lower RPMs than at higher ones. Added fuel injector cleaner to gas for a couple tanks, no change. My mechanic has checked spark plugs, fuel injector, o2 sensor, and everything is ok. Dry compression test shows good compression. He thinks it may be a valve sticking, which means a valve job: expensive. Is there anything else that can be done? Why is there no misfire when it is first started?

View 9 Replies

Santa FE SM (2001-06) :: Engine Light Come On With Code P0302 Cylinder 2 Misfire

I have a 2005 Santa Fe with the 3.5 with 112000 miles on it. I had the engine light come on with the code P0302 cyl #2 misfire, I got spark plugs, plug wires to do a tune up on it. I changed all of it and got it back together, started it up and it still had a miss to it. I then took the front spark plugs out and did a compression test on it. #2 was at 85, #4 was at 120, and #6 was at 160. I couldn't check the back cyls because I had already put the intake back on. I then did a wet test, and all the cyls came up to 160. So this tell me that the piston rings are bad in #2 and going bad in #4. I have kept all the oil changes up and up to this point I haven't had any trouble with it. Having this problem with there 3.5?

View 1 Replies

Santa FE SM (2001-06) :: Engine Having Hiccups When Accelerating - Code P0302 / Misfire On Cylinder 2

2005 3.5L FWD. 5 days ago I left the house, the engine was running smooth at idle but having hiccups when accelerating. Check engine light went on when accelerating but going off at idle. Turned around at the first stop light, parked the car home and pulled code P0302 misfire on #2 . Figured it's most likely the coil, was going to order one next day but to my surprise, no more check engine light next day and engine has been running smooth since then. Probably drove 100 miles since with no issues. I have 6 spark plugs waiting to be replaced but it's too cold to do it right now unless it's an emergency. Car has 105k miles now, spark plugs were changed at 63k. Was this just a fluke and P0302 will probably not come back or should I not risk it and just go ahead and replace the coil? If I end up replacing the coil, should I do one coil or all three?

View 22 Replies

Ignition - Civic - Honda - Misfire :: 1996 - Check Engine Light Is On / Code P1382

The check engine light is on in my 1996 Honda Civic. The code for it is P1382, which is supposed to be either a misfire or the ignition control system. It runs fine most of the time, but intermittently cuts out while I am driving sometimes. I have replaced the spark plugs and fuel filter and the check engine light actually went off after replacing the fuel filter, but came back on the second time I drove the car. The distributer was replaced not quite a year ago with a reman distributor.

View 2 Replies

Elantra XD (2001-06) :: Check Engine Light Will Pop On Occasionally And Code Reads Random Misfire

2004 Elantra AT ... 6 months ago top of the radiator cracked caused it to overheat and blow the head gasket and warp the head. Repaired that and compression is fine now. It ran great for 4 months but now it randomly stalls. at or near idle. Seems to do it more at operating temp rather then cold. Occasionally the check engine light will pop on and the code reads (random misfire). It acts just like it has been shut off. But immediately restarts.

View 3 Replies

Civic - Honda :: Cylinder 2 Misfire Code As Well As Random Power Loss

I had plugs and wires changed to try clear code. Car seemed to do some better but while trying to go up a steep hill car started stuttering and jerking. Power went out of car and check engine light started blinking fast. After let the car sit for bout 45mins car started running fine again and light stopped flashing but remained on. Code read cylinder2 misfire again.

View 1 Replies

Honda - Grandcherokee :: Check Engine Gas Cap Code On 2001 Jeep

My daughter's Jeep check engine light is on. Trying to get the car inspected so cannot be ignored. I think the code wasP0422, indicating it needed a new gas cap. We bought a new gas cap, cleared the code and it went away for a few days but before she could get it inspected, the light came on again. I saw similar problems suggestions were to get a better gas cap (we got one at autozone), or it could be something like a pump problem. We haven't taken to a dealer - it's a 2001

View 17 Replies

Honda - Odyssey :: 2001 - Recurring Check Engine Code Cat Converter P0420

I have a 2001 Honda Odyssey with 90000 miles. Lat last year around Oct/Nov time frame, check engine light came on. I took my vehicle to a local Auto Zone store and they scanned the code and told me it was P0420 - bad catalytic converter.

I replaced the cat converter with an after market model, however after 3/4 months (after driving 2000 to 3000 miles), check engine light came on with the same code. The mechanic changed the cat converter and put a new (after market model). Again after 3/4 months (2000 to 3000 miles) check engine light came on again. And this time the mechanic replaced the cat converter and also oxygen sensor. Now after 4 months or so the check engine light is on the vehicle again.

The mechanic is now saying that the problem is not with the cat converter and he is saying there is a lot of abnormal deposit on the vehicle. When he scanned again he found another issue that read something like "high voltage" and this time the guy thought may be due to short circuit (per code) the fuel injector is sending high volume of fuel and this is causing excessive fuel to go into the cylinder and hence high volume of emission. I replaced the fuse box again and after another 100 miles or, the problem is reappearing.

View 11 Replies

Intrepid :: 2001 SE - Misfire In Cylinder 4 (Code P0304)

Have '01 SE. yesterday I got a misfire in cylinder 4 (code P0304) the service light blinked on and off 3 to 4 times than stayed solid. changed plugs and boots about 1 to 2 months ago, didn't change coils and they r not in the best shape but didn't have money to replace at time. So I replaced the coil for #4 and it still runs rough with code, plug has some ware but looks fine.

View 1 Replies

Golf IV / Jetta IV :: 2001 1.8T - Cylinder Misfire Code

I recently changed my spark plugs + coil packs in my 01 1.8T because it read a couple cylinder misfire codes. Drove it for a few days out of curiosity plugged the code reader in again and it's still reading misfire codes. What could the issue be still?

View 6 Replies





Copyrights 2005-15 www.bigresource.org, All rights reserved