I have changed the clutch master cylinder on my '03 Honda Accord (6 cyl.) six times in the past 12 months. Either the o ring seal blows out or the bolts holding the plate down breaks off. I bleed the clutch of bubbles until the oil runs through also. What am I doing wrong?, I'm about to send this car packing.
View 9 RepliesI just rolled over to 90,000 miles on my 2002 Accord. Its running beautifully, however every so often the car "rumbles" or "shudders" when I'm releasing the clutch after I shift into second gear, or sometimes it'll do it when I'm facing up a hill pulling into first gear letting out the clutch. Its almost as if the clutch rapidly grabs then slips a bunch of times, similar to if it was warped. It doesn't completely slip at all to my knowledge. The car was bought new by my family and has been driven pretty carefully since (although 2 people have learned to drive stick on it, and my dad isn't the most "gentle" driver in the universe). I know that Clutch rebuilding and replacing is a big expensive job and its something I wouldn't even consider doing myself. So, when is it time to really seriously consider dropping down the serious cash to get the clutch rebuilt? To be honest, the shuddering is really annoying (it doesn't happen all the time though) but its something I could live with for a bit.
View 8 RepliesI have a 2002 Accord with about 130k miles on it and the brakes don't have nearly the power that they used to. The pads and rotors are due for replacement but even then, the system is pretty weak. Would replacing the master cylinder? What about simply replacing the brake fluid (I doubt it has ever been changed)? And/or the calipers? The car is in great condition and I really like it so I don't mind investing some time and money to get more years out of it.
View 10 RepliesReplaced clutch master cylinder last week. Now when I accelerate it revs the RPM's and finally catches after about 5-10 seconds. Is this related to the previous repair? They are saying needing new clutch. What to do?
View 3 RepliesI am looking for a how to vid or resource on doing the job right. I purchased the complete replacement master cylinder from Napa. 2002 7.3 Powerstroke
View 3 RepliesI have a 79 f150. I changed two brake lines and master cylinder and bleed,and more bleed,but still very soft all most to floor? wheel cylinders look good.
View 2 RepliesCar ran great prior to sitting for 4 months. Tried to jump it and it wouldn't turn over, so i figure the battery was dead. I replaced the batter with a new one, had fresh fuel added.
I then thought perhaps it might be the started, so I removed it and had it tested and it passed (it's working). Car still wont crank. I turn the key and there is nothing not a sound, except the fuel pump. No crank nor click? Not sure where to go from here?
I started having a strange clicking sound when pushing down the clutch pedal. I have 43,000 miles on it and I have driven the clutch well(I really don't believe I already worn it up). It goes away and then it comes back. There is no problem on shifting from gear to gear, it works just fine. It is only when I push the pedal that it starts clicking like it pushing against something. The car dealership was so useless, they said I need a new clutch and that warranty does not cover it because I may have been using the clutch badly. Also do you think that they have the right to tell me it is my fault even though I have the extended warranty for 100, 000 miles.
View 6 RepliesVehicle is an '86 Comanche 2.5L. Tested the battery at standing and charging, came to 12.8 standing and 14.7 charging. The alternator relay clicks, though that doesn't necessarily mean it's in good working order.
Any electrical load applied; headlights, taillights, hazards, blinkers, etc. kill the engine.
The clutch master cylinder is leaking onto the fuse box, though I moved it as best I could as I don't have the funds for a new master cylinder right now and I'm not sure which fuses, capacitors, and relays do what on the fuse box as the writing is barely noticeable.
I bought a new clutch master cylinder for my 1960 Land Rover. I have swapped these in and out and rebuilt or replaced them many times over the years. This is the first time I've seen one fail this way, and it is brand new out of the box. In my opinion, the seal at the back of the cylinder that is supposed to close off the reservoir from the inside of the cylinder, well, isn't. So, it is pushing fluid up into the reservoir instead of down through the lines. Have a look at a this video...... [URL] ....
View 4 RepliesI'm having trouble bleeding the air out of my slave cylinder or master cylinder in my clutch system. I've been trying for a couple days now is there a trick to this?
View 7 RepliesA couple of years ago I went through the salt water with my 2003 Honda Accord which is a manual transmission. It only has 106,000 miles and expects it to go much further. The clutch works great but when engaged is really loud. I have had it checked by 2 different auto repair places. Nothing is wrong they say. It has been cleaned and greased.
View 19 RepliesI have a 88 ranger supercab 2.9l 4x4 with the fm146 trans and recently I have had a problem with my clutch master cylinder rod falling off my clutch pedal. I bought the new bushing and put it on and it was fine until yesterday. It wants to keep coming off. Is there a clip of some sort to hold it on or no. I looked at a few at the salvage yard and they did not have a clip just the bushing. So what do I do?
View 1 RepliesI spent the day with a buddy working on his 91 ranger 4 cylinder 2WD truck because the clutch master cylinder shaft that connects to the pedal bent. We took the old part out and replaced it, but now we are having problems with the little pin that holds the line from the slave cylinder to the master cylinder in place. For some reason, even though the line is securely in position and wont budge with the pin in, it still leaks so we are unable to bleed the clutch.
I have looked all around the internet, including this site and wasn't able to come up with any explanation as to why the line is leaking, perhaps it is because the line isn't pushed in far enough, but like I said, it is securely in place and I wasn't able to push it in farther before forcing the pin into place. My buddy and I spent about 9 hours working on his truck today, including probably 3 or 4 just on trying to stop the leak.
My Ranger had been shifting hard for quite awhile. I recently opted to go ahead and replace the clutch, throwout bearing, had the flywheel turned and replaced the pressure plate.
This just seemed to make the problem slightly worse. I thought it was possible that my master cylinder needed to be replaced (the slave was replaced two years ago and didn't appear to be leaking when I had the tranny off). I replaced the master cylinder and now the clutch won't disengage at all. I've spent several days trying different things to bleed the clutch, and I just can't get it to bleed. I took it back off and bench bled it, then put it back on and bled through the whole system. This isn't working. I've tried numerous suggestions-jacking up the back end of the truck, jacking up the drivers side of the truck, I even bought a vaccuum bleeder and used it for 2 hours just having an assistant fill up the reservoir while I sucked fluid out the bleeder valve. The best I could ever get was some resistance on the pedal, but not enough to push the disc away from the flywheel.
I took the pickup to Ford, they said they bled it and charged me 90 bucks and still couldn't get the clutch to release
I'm in the process of replacing the clutch master cylinder in my 99 F250 7.3L. I've got the kit that includes all the components already pressurized in a complete assy. Anyway, I know that in order to remove the clutch pedal component, (the part that stick's thru the firewall) your supposed to be able to rotate it about 45deg and it should pull free from the piston attached to the clutch pedal. But, what happens when it will not come free? I've already got a new replacement kit and I can see where that stainless rod inserts into the plastic component, but I can't seem to get the one on my truck to release?
View 1 RepliesI have a 2002 Honda Accord SE with 228K miles. Leaking oil (oil spots on garage floor). My mechanic, where I get my oil change, said it looks like it is leaking oil and transmission fluid- he referred me to a reputable auto repair shop. The auto repair shop put some kind of dye in my car and told be to bring it back after driving 50 miles. Two days later I took my car back. They said I was not leaking transmission fluid but oil. They said my valve gasket, and my cam, crank, and balance shaft seals are bad.
They replaced the gasket and seals. I also had them to replace my timing belt and water pump since it was last changed at 113K miles. I continued to find fresh oil spots on my garage floor. I returned to the auto repair shop. They inspected my car and said I need to replace the VTEC gasket. I had them to replace the VTEC gasket. A few days later, I noticed some more oil drops on my garage floor. I returned to the auto repair shop and told them to keep it until they discover where the leak is coming from. My car is currently at the auto repair shop two days later. Do you think this oil leak problem mean that the end of my car is near? Is it worth repairing?
It usually takes three times of trying to start before it actually completely starts,it starts then immediately stalls usually twice and on the third try it starts right up.
View 4 RepliesThe factory 'Security System' aka alarm, in my 2000 Honda Accord EX goes off randomly. When this happens the horn sounds and lights flash for several minutes at a time. This can happen several times in one day and then not happen again for days or weeks. The owner's manual says that the security system is activated when the doors are locked and will sound an alarm if a passenger door, trunk lid or hood are opened while the system is activated. The system is deactivated by using either a key or the remote transmitter to unlock the doors. My mechanic tried to disable the hood latch switch, but this caused the alarm to sound continuously. How to fix the problem or disable the security system?
View 4 RepliesMy car keeps on shaking at times, sometimes it is perfect all day. If it is shaking and I come to a light it stops. I have been to several mechanics and they all say something different.
View 1 RepliesOn my 95 Honda Accord 4-door (>400K miles), every time the doors are locked, the servos click 25 to 60 times about once a second. Like a loud ticking clock. The doors are locked OK, but the clicks sound like the mechanism is wearing itself out. Is there an easy fix? It may be related to installation a few weeks ago of a new alarm system that included a remote control lock. I haven't had time to have the alarm company look at it.
View 3 Replies