Gmc - Jimmy :: After Brake Caliper Replacement - Fluid / Air Not Coming From Bleeder Valve?
Jul 26, 2016
I replaced both rear pads calipers on my jimmy. Its 4 wheel drive. Now after installing them, I tried to them, and i nothing from the bleeder valve s. Someone said I could have the wrong caliper on the wrong side? Is that even possible? Also, the manual food this truck says it may be necessary to use a scan tool cycle/bleed these brakes. Ive changed calipers etc before, never had this issue on other vehicles.
View 19 Replies
Advertisement
I replaced a brake cylinder on my 2006 Focus rear drum brake. Now, I need to bleed the brake fluid, but I can't find a wrench to fit the nut.10mm is too small and 11mm is too big. What's going on? Could it be the rusted nut has grown in size enough to make the 10mm wrench too small? Or, is the nut standard?I know the drum bleeder nut I know the front disc brake bleeder brake is 10mm. So, I am thinking the rear should be metric, but since it's drum, I am not so sure. What the size is?
View 13 Replies
I have a leak from the rear driver caliper, it seems to come from behind the bolts that hold the emergency brake to the caliper (I had my wife push the pedal repeatedly so I could find the issue). I haven't been able to remove the retaining bolts (the allen head bolt doesn't want to play) to see what the issue might be.
View 18 Replies
Is it what it looks like? Why is it there, to pressure bleed the system through it rather than using a modified MC cap?
View 5 Replies
My left brake caliper locks up on me. I have replace it, the brakes , and the wheel bearings. when im driving down the highway and go between 45 -55 my front end shakes really bad and i start to lose power.
View 8 Replies
I have a '79 F150 4wd and was wondering what would indicate a caliper needing replacement. I'm already going to replace everything on my rear brakes, they are completely trashed. However, the fronts seem OK, NO indications of leaks or seizing both sides of the rotors appear to be evenly "used" I guess. The inner pads do seem to be thicker than the outer pads is this normal? Anything I should be specifically looking for before I have the rotors turned and put a new set of pads on?
View 5 Replies
2003 F-250 SD 7.3L Supercab
Problem 1: Right rear
Occasional smell of heavy grease, white smoke billowing out from under wheel well (once), black fluid leaking from lower area of caliper. Told it could be axle seal or caliper. I'm leaning toward axle since the caliper is only 1 yr old (NAPA OEM).
Oddly, I also notice a loud, piercing screech when going around traffic circles or exit ramp clovers to the right. I thought this was my trailer until it did the same thing without it.
Axle or Caliper?
Problem 2: Left front
Local mech advised the bleeder valve is broken off in to the unit and cannot be simply replaced. Insists it needs whole caliper. If pedal is all the way up there is a temporary breaking capability then it slowly creeps to the floorboard, hits a brick, and keeps rolling. Replaced master cylinder a few months ago when it same. Drove it for the last 2 weeks and problem is back.
Removing broke-off bleeder valve instead of replacing cals?
View 3 Replies
Every time I am pressing the brake pedal, I hear a distinct clicking sound coming from passenger front Brake Caliper Area.
I have applied brake grease (green) to the pad shim.
I have replaced the spring sets on each front caliper.
Passenger Brake Clicking Lexus LS460L - YouTube
View 8 Replies
I was getting a check engine light with a P1112 code, so I had a mechanic replace the coolant flow control valve. There's a TSB on that and it seems to be the thing to do. But after the replacement, I'm getting overheat warning light whenever the engine needs to work hard. Also, the cabin heater only works when the gasoline engine is not running... when the engine is off, I get heat (though it's not as hot as I'd think when I have it on max heat), but when the gas engine kicks in, the cabin heat disappears.
View 8 Replies
2010 F250, what size tube do I need to fit on the brake bleeder screw? The tubes I have are all too big and the size marks are no longer legible.
View 4 Replies
I was advised to replace my brake and power steering fluild at 40,000 by the Chrysler Dealer. Ever heard of this?
View 8 Replies
On my 2011 Prius maintenance schedule, there is plenty of direction about inspecting brakes; however, there is no indication of when to flush and replace the brake fluid. My wife travels 60 miles/workday, but hits her brakes about 6 times/day. I would expect that normal braking would result in pad replacements more regularly than we are going to have. I did most of the 60K inspection, but took the car to a trusted, local mechanic for undercarriage inspection and a professional look-see. They indicated that the brake fluid should be replaced every 3 years, and I OK'd a flush and refill. Is there any professional guidance on the replacement interval? I know there are a lot of opinions, but I wonder if there is any published authority.
View 15 Replies
2006 GS430 110K miles. Did Front brake pad change by myself. Now ABS , brake warning lamps come on.
Bring it to Lexus dealer. They found 3 code on it. C1203, C1336, C1345
After performed the Zero Point Calibration, the DTC C1345 remains.
I felt so bad. They want to charged me another $185 in order to find out the problem after I have paid $130. But i am out of pocket. So drive car back to home. I don't think i did anything wrong while changing brake pad. Just remove the caliper and push the piston back.
Detail of the Code:
C1203 engine control system communication fault
C1336 zero point calibration Yaw rate sensor undone
C1345 Linear valve offset not learned.
View 14 Replies
My 2007 Prius (151,000 miles) just started making what sounds like a scraping sound when in motion. This does not happen every time I drive it. The dealership said I need to replace the brake fluid actuator pump.
He couldn't really tell me what would happen if I don't have it fixed. He said perhaps the power brakes would go out, or maybe the anti-lock brake system. Either way, I don't want to mess with possible brake failure. But the cost of this repair is so high, and my car already has 151,000 miles. I'd love to drive it to 300,000 miles if I can, but am I being realistic? I'm wondering if it's worth investing this much money in a car with so many miles.
View 5 Replies
So I had a stuck caliper on the driver rear side. I pushed the piston back and checked everything to make sure all was in working order. After some though and reading about the calipers getting stuck which old brake lines, I decided to upgrade the line with the Russell stainless steal lines.
I got all the lines put in but I seem to have fluid leaking on the passenger side fitting which I can't seem to get to stop. I put the old line back in but it is still leaking. I am not sure what I need to do or check to get it to stop. It seems to be leaking from the thread area. I checked the fittings and they don't look cross threaded so I don't understand why it may be happening.
View 3 Replies
So my 2007 Accent/Hatchback started having this weird issue the other day.
My Parking Brake/Low Brake fluid Level Warning Light will coming on while driving and then all the gauges drop down. The light goes off and the gauges come right back up. All this happens within 2-4 seconds maybe. And usual happens maybe once every 6-7 times I drive it so not all the time.
I am driving, not braking so even more confused.
View 3 Replies
I recently noticed that my brake fluid was leaking in my 2003 Hyundai Elantra and upon further inspection I found the leak was coming from a part near the master cylinder. I looked online and couldn't figure out if this part was part of the master cylinder or brake line or a part all on its own. I tried tightening it but It still leaks some. I read a similar post online and that it could just be that the washer needs replaced but I just wanted to check on here to see what the part is called and if I should just replace the whole thing. I included photos as well.
View 7 Replies
My driver side caliper will not bleed fluid, is it safe to say that the caliper needs replacing.
2000 f 150 4.2 v6 232,000 miles
View 13 Replies
the brake warning light ( on the dash ) is randomly going on and off, even at driving speeds. have had it looked at but no problems could be found. the brakes are fine ,couldn't find any wiring problems. some days it won't even come on at all ,and some days it does with no particular pattern.
View 1 Replies
I have an 02 f150 5.4 and since I got it it hasn't had cruse control. I went to a local ford dealership and they ran the vin and didn't find any recall on it. Under the hood on the master cylinder there is brake fluid coming out of the brake control switch. Would I have to do something with the harness too?
View 9 Replies
My wife was complaining about a metallic scraping noise that was coming from the driver side front wheel. I listened to it and couldn't determine what it was or see any evidence of something loose. I took off the wheel and had a look at the components and after 160K miles, it looked like the pads could use replacing. It didn't seem like that was the root of the sound, but it looked like they needed to be done.
I got the parts for both sides and replaced the left without issue, but when I got to the right side, I found the source of the noise: a pebble between the rotor and dust shield. I continued on with the brake replacement and the caliper piston was stuck. Tried a couple of things to free it and blew out the piston.
View 11 Replies
